1. INTRODUCTION AND SAFETY PRECAUTIONS

2 GENERAL

3.1 Front Overview

3.2 Rear Overview

3.3 Instrument Panel Overview

4 INSTRUMENT CLUSTER OVERVIEW

4.1 Instrument Cluster (K2/K2+/K4+)

4.2 Instrument Cluster (K6+/K8)

4.3 Warning Lamps Overview

	Airbag warning Lamp		EPS Malfunction Lamp		Low Oil pressure Lamp		Battery Charge Lamp		ABS warning Lamp		High Temperature Lamp
	Left indicator		Start Stop Lamp		Glow plug warning Lamp		Seat Belt warning Lamp		Front Fog Lamp		Security Lamp
	Right indicator		Check Engine Lamp		Low fuel warning Lamp		ECO Lamp		Park Lamp		Head Lamp High Beam
	Door Ajar Lamp		Park Brake/ Low Brake fluid / EBD malfunction Lamp		Water in fuel warning Lamp		Malfunction Lamp

5 SEATS AND SEAT BELTS

5.1 Driver seat

5.1.1 Sitting in the Correct Position

Follow the tips below for a comfortable and safe journey;

• Sit in an upright position with the base of your spine pressed against the seat back
• Adjust the head restraint (if applicable) as close as possible to the above specified position, with the top of the head restraint even with the top of your head
• Maintain sufficient distance between yourself and the steering wheel. Maintain at least a ten inch (10") distance from the centre of the steering wheel to your chest
• The top curve of the steering wheel should align with your chin for ideal road visibility
• Adjust your seat and seat back angle such that your wrists rest on top of the steering wheel freely
• Ensure your legs are in a bent position while fully depressing the clutch pedal

The seat should be adjusted while still maintaining control of the foot pedals, steering wheel and your view of the instrument panel controls.

5.1.2 Front Seat Slide

Move the seat forward or backward by lifting the adjustment lever located under the seat front and release once the desired position is reached.

5.1.3 Front Seat Recline

To adjust the seat back, lift the recline lever located on the outboard side of the seat, lean back and release the lever at the desired position. To return the seat back, lift the lever, lean forward, and release the lever.

5.1.4 Driver Seat Height Adjust (if equipped)

Lift/Push the seat height adjustment lever located on the outboard side of the driver seat to raise/lower the seat. Adjust the seat height such that you are able to depress the clutch pedal completely.

5.2 Head Restraint

5.2.1 Fixed Head Restraint (If applicable)

Your vehicle front seats are equipped with fixed head restraints. The head restraint help to avoid the whiplash injury on the neck in the event of rear collision.

The Fixed head restraint comprises of the padded portion which contacts your head and the seat back.

5.2.2 Adjustable Head Restraint(If applicable)

The head restraint comprises of the padded portion which contacts your head . It is inserted/locked in receptacles on the top of the seat back.

Your vehicle front & rear seats are equipped with head restraints which are vertically adjustable. The head restraint help to avoid the whiplash injury on the neck in the event of rear collision.

Always align top of the head restraint with the top of your head or as close to it as possible. To raise the head restraint, press the lock knob and pull the restraint up. To lower the head restraint, press the lock knob and push the head restraint down.

5.2.3 Removing Seat Head Restraint

The head restraint can be pulled out completely by depressing the locking button while pulling the restraint out.

5.2.4 Installing Seat Head Restraint

Align the head restraint shafts over the holes on the seat top and push the restraint straight down till you hear the lock click.

Keep the seat back as upright as possible so the headrest is behind, not beneath, and almost touching your head.

Never drive with the head restraints not properly adjusted, head restraints removed or inserted in a flipped condition. With no support behind your head, your neck could be seriously injured in a collision.

5.3 Front Foldable Armrests (if equipped)

Front middle seat backrest can be folded and utilized as arm rest for both front occupants.

Pull the lock upwards and fold the middle seat backrest to the required position

To straighten the middle seat backrest, pull the lock upwards and lift the backrest to the vertical position

5.4 Second Row Bench Seat

Seat Fold

The second row seat back can folded forward for maximum cargo space.

To fold the second row seat back down, pull the knobs at the top both sides of the seat firmly and push seat back forward. Ensure the head restraints on the second row seat are lowered all the way down before attempting to fold.

Optionally cushion can also be flipped forward before folding the backrest to achieve a flatter luggage floor

5.5 Rear Foldable Arm-Rests

Second row middle seat backrest can be folded and utilized as arm rest for rear seats.

Pull the strap and fold the middle seat backrest to the required position

5.6 General Warnings and Instructions- Seat Belts

At least once each month, inspect the seat belt webbing for any cuts, tears, or other signs of wear (such as fraying along the edges). Also inspect the anchors, retractors, and buckles to be sure they are tight and operational.

• All occupants, including the driver, should always wear their seat belt no matter how short the trip in order to minimize the risk of severe injury in the event of a crash. In an accident, an un-belted passenger becomes a projectile, and can cause serious injury to himself or another passenger.
• In a rollover crash, an un-belted person is significantly more likely prone to Injury than a person wearing a seat belt
• In order to be properly buckled, you must always sit up straight and keep your feet on the floor in front of you. The lap part must be worn low and tight across your hips, just touching the top of your thighs. While fastening the seat belt, the shoulder strap of the seat belt must pass over your chest and top of your shoulder. It must never touch your neck, face, the side of your shoulder, arm, or pass under your arm. The belt must always be flat against your body and not twisted in any way. Nothing, such as an arm rest, a pocketbook, or any external objects should be between you and the seat belt. Improper wearing of a seat belt will reduce the protection in an accident.
• Seat belts should be adjusted as tightly as possible, consistent with comfort to properly secure the wearer in the seat.
• The seat belts provided for your vehicle are designed for people of adult size, must be properly used and maintained.
• For usage of adult seat belt to secure children refer to section on manual for child seat positions and use of child restraint systems
• Passengers should not move out of or change seats while the vehicle is moving. A passenger who is not wearing a seat belt can be thrown against the inside of the vehicle, against other occupants, or out of the vehicle during a crash or emergency stop
• Do not use any accessories on seat belts or modify in any way the seat belt system. Devices claiming to improve occupant comfort or reposition the seat belt can reduce the protection provided by the seat belt and increase the chance of serious injury in a crash
• An accident or emergency stop, can damage your seat belt system, even if the accident is “minor”. Please have your Authorized Mahindra Dealer inspect the seat belt system after an accident
• Please be aware that any unsecured item in your vehicle, such as your pet, unsecured child restraint system, or a laptop, can become a projectile in the event of an accident or sudden stop, causing injuries to occupants in the vehicle

• Seat belt systems can be prone to abuse. They are not indestructible. They must be handled with care to avoid damage
• Keep the belts clean and dry. Belt retraction may become difficult if the belts and webbing are soiled. If they need cleaning, use a mild soap solution or lukewarm water. Never use bleach, dye, or abrasive cleaners. These chemicals will severely weaken the belts
• Retractors in a 3 point type seat belts retract the seat belts when not in use. The inertia lock and coil spring allow the belts to remain comfortable on users during normal driving. During accidents or abrupt stops, inertia locks restrict the forward movement of the wearer

Persons with serious medical conditions should also wear a seat belt. Consult your doctor for specific recommendations before travel.

Pregnant women must also wear seat belts. Consult your doctor for specific recommendations.

The lap belt should be worn snugly and as low as possible over the hips. The shoulder belt should be worn across your shoulder, but never across the stomach area. When worn properly, the seat belt will protect both the mother and the foetus in an accident or emergency stop.

• Reduce the possibility of being thrown from your vehicle
• Reduce the possibility of injuries to lower body and legs during an accident
• Hold the driver in a position which allows better control of the vehicle

Children who are too large for child restraint systems should always occupy the rear seat and use the vehicle seat belts. The lap portion should be fastened snug on the hips and as low as possible and the shoulder strap should be across the child's shoulder, not the neck or face. If you are unable to position the strap across the child's shoulder, the child should remain in a booster seat. Frequently check the seat belt to be sure it remains snug and in position. A squirming child could cause the seat belt to come out of position.

5.7 Fastening the Seat Belt

5.7.1 3-Point type (if equipped)

Adjust the seat as needed and sit up straight and well back in the seat. To fasten your seat belt, pull the webbing out of the retractor and insert the metal tab into the buckle. There will be an audible “click” when the tab locks into the buckle. Pull up on the shoulder strap to tighten the lap belt across your hips. The seat belt retractor will pull in any slack in the shoulder strap. A slow and easy motion will allow the belt to extend and let you move your body around freely.

Periodically check the seat belt as you ride to be sure it remains snug and in position. If there is a sudden stop or impact, the belt will lock into position. It will also lock (restrict) if you try to lean forward too quickly.

5.7.2 2-Point Lap type (if equipped)

This seat belt is applicable in some seating positions in some variants as applicable. Insert the metal tab into the buckle until it snaps. Position the lap belt on the hips as low as possible.

5.7.3 Unfastening the Seat Belt (both 3-Point & 2-Point)

To release the belt, press the buckle release button and allow the belt to retract. If the belt does not retract smoothly, pull it out and check for kinks or twists. Then make sure it remains untwisted as it retracts.

5.8 Child Restraint System (CRS) Using Seat Belts

Always secure a child in a proper Child Restraints System in accordance with age and size of the child as recommended by the child restraint system manufacturer. Be sure to follow the Child Restraint System (Child seat) manufacturer’s instructions for seat belt routing.

Driver + 5 Seater (If equipped)

Driver + 4 Seater (If equipped)

Legend:

U — Suitable position for using universal child restraint system using seat belt and buckles marked with ‘ C R S ’.

Ø — Not Suitable position for using child restraint system using seat belt.

5.9 Child Restraint System (CRS) Using ISOFIX (If equipped)

Driver + 5 Seater

Driver + 4 Seater

Legend:

IU — Suitable position for using universal rearward facing child restraint system using “ISOFIX and Top tether”.

IUF— Suitable position for using universal forward facing child restraint system using “ISOFIX and Top tether”

Ø — Not Suitable position for using child restraint system using “ISOFIX and Top tether”

Location of ISOFIX & Top tether

6 SUPPLEMENTAL RESTRAINT SYSTEM (SRS) (if equipped)

6.1 Airbags

• A Frontal airbag for driver – located in steering wheel hub
• A Frontal airbag for front outboard passenger – located in instrument panel on passenger side

They are indicated by “SRS AIRBAG” embossed on steering wheel / Instrument panel respectively

To minimize the risk of severe injury in the event of a crash, every passenger must always wear their seat belt (see the chapter on Seat Belts in this manual). The airbags inflate very quickly with great force. Do not position any part of your body too close to a airbag, you or especially children could be seriously injured/killed by a deploying airbag.

6.2 Introduction

The Supplemental Restraint System (SRS) includes airbags, and ECU. The airbags are designed to provide additonal protection to the vehicle occupants over and above the primary protection provided by the seat belts.

The primary components of the SRS are the sensors which measure the deaccelration intensity. In the event of a frontal impact,intensity being above the threshold the SRS airbags inflate to work in conjunction with the seat belts and help reduce injuries mainly to the driver's or front passenger's head/chest.

6.2.1 Driver and Front Passenger Airbag

Your vehicle is equipped with a Supplemental Restraint System (Airbag) and lap/shoulder belts at both the driver and front passenger seating positions. The indications of the system's presence are the letters “SRS AIRBAG” embossed on the airbag pad cover in the steering wheel and the passenger's side front panel pad above the glove box.

The SRS is designed to deploy the front airbags only when an impact is sufficiently severe and when the impact angle is less than ± 30° from the forward longitudinal axis of the vehicle.

Front airbags are not intended to deploy in side-impact, rear impact or rollover crashes. In addition, front airbags will not deploy in frontal crashes which are below the prescribed deployment threshold where risk of serious injuries is low.

6.2.2 Airbag System Malfunction Lamp

Airbags do not require any regular maintenance of service. The airbag system malfunction lamp illuminates when the ignition is ON, and it turns OFF after about 3 seconds as self check confirming normal operations of airbag system and malfunction lamp.

This lamp monitors airbag sensor assembly, airbag sensors, indicator lamp, inflators, interconnecting wiring and power sources.

• The lamp does not glow when the ignition is switched ON or glows beyond six (6) seconds after switching the ignition ON
• The lamp comes ON at any other time, even briefly
• The lamp comes ON intermittently

Even if the airbags do not deploy during an accident, take your vehicle to an authorized Mahindra Dealer for a thorough inspection of the airbag and seat belt systems, no matter how minor the accident. The airbag system could have been damaged, and may not work as intended in the future, resulting in serious injury.

6.2.3 Airbag Inflation/Deployment

The airbag sensors constantly monitor the forward deceleration of the vehicle. If an impact results in a forward deceleration beyond the designed threshold level, the system triggers the airbag inflators. This initiates a chemical reaction which quickly fills the airbags with non-toxic gas.

Upon deployment, tear seams molded directly into the pad covers separate under pressure from the expansion of the airbags. Further opening of the covers allows full inflation of the airbags. A fully inflated airbag, in combination with a properly worn seat belt, slows the driver's or the passenger's forward motion, reducing the risk of head and chest injury.

After complete inflation, the airbag immediately starts deflating, enabling the driver to maintain forward visibility and the ability to maneuver or operate other controls.

Deployment of the airbags happen in a fraction of a second, producing a loud noise releasing a ‘white smoke’ and residue along with a non-toxic gas. This does not indicate a fire. This smoke may remain inside the vehicle for some time, and may cause some minor irritation to the eyes, skin or breathing. Be sure to wash off any residue with soap and water as soon as possible to prevent any potential skin irritation. If you can safely exit the vehicle, you should do so immediately.

• The driver must sit as far back as possible from the steering wheel while still maintaining control of the vehicle
• The front passenger must sit as far back as possible from the dashboard
• Sitting improperly or out of position can cause occupants to be shifted too close to a deploying airbag, strike the interior structure or be thrown from the vehicle resulting in serious injury

6.2.4 Child Restraint and Airbag (if equipped)

Never place a Child seat (Rear-facing or Front facing) restraint in front passengers seat, if passenger airbag is present. Because, If the airbag deploys could cause serious or Fatal injuries to the child.

6.2.5 Airbag Deployment

Front airbags are designed to inflate in a frontal collision depending on the intensity, speed or angles of impact of the front collision.

Impacts below a pre-determined threshold level may not cause the airbag’s to deploy in the following cases:

• Collision with Utility Poles or Trees

  Airbags may not inflate if the vehicle collides with objects such as utility poles or trees, where the point of impact is concentrated to one area and the full force of the impact is not delivered to the sensors.

• Under-ride Situations

  Running under a truck's tail gate may not provide the decelerations necessary for airbag deployment. Just before impact, drivers often brake heavily. Such heavy braking lowers the front portion of the vehicle causing it to “ride” under a vehicle with a higher ground clearance. Airbags may not inflate in this “under-ride” situation where deceleration forces that are detected by sensors may be significantly reduced by such “under-ride” collisions.

  
• Rear-end Collisions

  Frontal airbags are not designed to inflate in rear collisions, where occupants are moved backward away from the airbags by the force of the impact. In this case, inflated airbags would not be able to provide any additional benefit.

  
• Frontal Impact

  Frontal impact beyond 30º range from head-on to the vehicle.

  
• Potholes or Stepped Surfaces

  Driving into a big pot-hole, stepped surface or hitting the far side of a hole/incline will not inflate the airbag.

  
• Rollover

  Airbags may not inflate in rollover accidents where airbag deployment would not provide protection to the occupants.

• Frontal Side Swipe Impact

  Frontal offset impact to the vehicle may not provide the deceleration force necessary for airbag deployment. In an angled collision, the force of impact may direct the occupants in a direction where the airbags would not be able to provide any additional benefit, and thus the sensors may not deploy any airbags.

6.2.6 Airbag Replacement

Self-servicing or tampering with the airbag system is dangerous. An airbag could accidentally deploy causing serious injuries, or will not deploy when there is a need. Always take your vehicle to an Authorized Mahindra Dealer for inspection and repairs.

6.2.7 Self Removing SRS Related Parts

Self removing the instrument panel, steering wheel, seats or airbag related parts or sensors is not recommended. Airbags could accidentally activate and cause serious injuries, or they may not deploy when there is a need. Visit an Authorized Mahindra Dealer if these parts must be removed.

6.2.8 Airbag Disposal

Improper disposal of an airbag or a vehicle with live airbags can be extremely dangerous. Approach an authorized Mahindra dealer to do these jobs.

6.2.9 Airbag Repair

If the front airbag cover or passenger airbag cover shows signs of damage or having been removed, the vehicle should be towed to the nearest authorized Mahindra dealer for repair. Do not attempt to self repair or reinstall the cover.

6.2.10 Airbag Maintenance

For cleaning the airbag covers/areas, use only a soft dry cloth or one which has been moistened with plain water. Solvents or cleaners could adversely affect the airbag covers and proper deployment of the system.

7 LOCKS AND KEYS

7.1 Locks and Keys

Your vehicle comes with two types of keys based on the model/variant;

• Remote Keyless Entry with Tailgate opening(RKE)
• Remote Keyless Entry with search option(RKE)
• Conventional key

Your key number is shown on the plastic tag attached to the key. It is recommended that you record the key number and store in a safe place. The keys operate all locks in your vehicle including those of the doors and ignition with steering lock. We advise you to keep one of these keys in a safe place for emergency use, but not in the vehicle. Should you lose your keys or if you need replacement keys, they can be ordered through an Authorized Mahindra Dealer.

7.1.1 Doors Opening

7.1.2 Locking/Unlocking the Tail Door

To open the tailgate press and hold the middle button in key for 2 seconds.

Push the tailgate gently to lock.

The Tail door can be opened by the lever located at the foot of the driver seat. Lift the lever up firmly to open.

Also Tail door can be opened with key. Turn the key anti-clock wise to unlock.

Push the tail door gently to lock.

Your vehicle is equipped with child safety locks on the rear door. When the child safety lock mechanism is enabled ON , the rear door(s) cannot be opened from the inside. The door(s) can only be opened from the outside.

Move the tab up/down in the slot provided in the side face of rear door to disable/enable the child safety rear door lock.

7.2 Central Locking System

All doors of the vehicle can be simultaneously locked or unlocked from the driver door.

7.3 Remote Keyless Entry (RKE) System

7.3.1 To Lock and Arm the Vehicle with RKE

• Press the LOCK button on the RKE for locking and arming the vehicle.
• Hazard lamps will flash once - if all the doors in the vehicle are locked and armed successfully using RKE.
• Hazard lamps will flash five times along with an alarm - if any of the doors (including bonnet) in the vehicle are open.

7.3.2 Unlock and Disarm the Vehicle with RKE

• Press the UNLOCK button on the RKE to unlock and disarm the vehicle.
• Magic lamps are activated (select variants) / Hazard lamps flash twice - if there was no theft attempt during the lock (armed) period.
• Hazard lamps flash four times along with an alarm - if there was a theft attempt during the lock (armed) period.

7.3.3 Auto Locking

All doors will get locked automatically when;

• All doors are closed properly, and
• Vehicle speed is greater than 20 kmph

Auto Locking ON DOOR OPEN — Once the auto lock has been activated, if any door is opened at any vehicle speed, then the auto lock will reactivate only if all doors are closed, the vehicle speed goes below 5 kmph & further crosses 20 kmph.

Auto Locking ON MASTER ACTUATOR UNLOCK — Once the auto lock has been activated, if the master actuator was unlocked at any vehicle speed, then the auto lock will reactivate only when the vehicle speed goes below 5 kmph and further crosses 20 kmph.

7.3.4 Auto Unlocking

Auto Unlock of all doors will happen when;

• From IGN ON to OFF, OR
• In the event of a crash (only on Airbag Variants)

7.3.5 Auto Re-locking

Auto Re-lock of all doors will happen when;

• No door status change for 45 sec after unlocking the vehicle using RKE

7.3.6 Search (Panic) Function

Press the SEARCH/PANIC button on the RKE to locate the vehicle in a parking lot. Panic alarm can also bring attention to the vehicle and surrounding area, warning about an intruder or seek for help.

When the SEARCH/PANIC function is ON, the hazard lamps flash along with an alarm for 30 sec. In this mode;

• Pressing the SEARCH button again switches OFF the alarm
• Pressing the UNLOCK button switches OFF the alarm and disarms/unlocks all doors

7.3.7 Mute/Un-mute Function

The chirps can be muted / un-muted. Press the LOCK & SEARCH buttons together for 3 sec. to toggle between MUTE/UN-MUTE mode. Hazard lamps will flash once to indicate the change in status.

7.3.8 Theft Alarm

Vehicle enters into alarm mode when there is a change in door status/ignition status provided the vehicle was locked through RKE.

• Alarm time - Pre-alarm (alarm with less intensity) for 5 sec. and continuous alarm for 25 sec. for the first time
• If there is any change in door/ignition status for the second time, the system enters the alarm state for 30 sec. without any pre alarm

After the alarm period, there will not be any alarm again till any further change in the door/ignition status.

7.3.9 RKE Operating Range

Using RKE, you can lock/arm or unlock/disarm the vehicle from distances approximately. 30 ft.(9 m).

• Check the distance: The RKE may be too far from the vehicle. Stand closer to the vehicle during rain or bad weather
• Check the location: Other vehicles or objects may be blocking the signals. Take a few steps to the left or right, hold the RKE higher, and try again. Moreover, closeness to a radio transmitter such as radio station tower, airport transmitter, mobile or CB radios may lead to reduction in range of RKE
• Check the RKE battery: See battery replacement procedure, given later in this section
• If the RKE is still not working correctly, contact an Authorized Mahindra Dealer

7.3.10 RKE Battery Replacement

If the RKE operation is inconsistent when any of the buttons are pressed it indicates that the RKE battery is weak.

The rear side of the RKE is screw fitted. Using a small screw driver, unscrew and separate the two halves of the casing. The battery type is button type “CR2032 3V cell”.

7.3.11 If RKE is Lost

If you have lost the programmed RKE, contact an Authorized Mahindra Dealer for procuring a new RKE.

While programming a new key set, you will have to submit all the keys available with you to an Authorized Mahindra Dealer.

7.3.12 Precautions while Handling RKE:

• Do not cover the key grip with any material that cuts off RF waves
• Do not leave the key exposed to high temperatures for a long period, such as on the dashboard or hood under direct sunlight
• Do not put the key in any liquid or wash it in an ultrasonic washer

7.4 Engine Immobilizer System

The Engine Immobilizer System is a security system that prevents the vehicle being operated by an unauthorized person. The Engine immobilizer prevents the engine from being started unless it recognizes signals from the correct coded key.

The system is automatically activated when the key is removed from the ignition.

7.4.1 Features of the Immobilizer System

• Prevents the vehicle being started by anyone not in possession of the correct vehicle key
• The vehicle is automatically protected after the key is removed from the ignition. At every ignition ON, if the vehicle does not recognize the correct key code, the engine check lamp will illuminate/blink and the engine cannot be started
• The vehicle will not be protected until the key has been taken out of the ignition

Inserting the correct coded key in the ignition and switching the ignition ON, automatically deactivates the system. This enables the engine to start.

8 FEATURES AND CONTROL

8.1 Power Windows

The quadruple switch controls the window winding functions of all the doors of the vehicle and is located on the driver door trim pad. It also houses a rear power windows lock switch for child safety that enables/disables the power window operation of both the rear doors when operated independently from the respective door.

To lower/raise the window glass push/pull the respective power window switch.

Rear passengers can also raise or lower their respective window glasses individually by the separate switches provided on both the door trim pads.

8.1.1 Power Window Lock Switch

A power window lock switch is provided in the quadruple switch bank which toggles the operation of the rear passenger power window switches.

8.2 Outside Rear View Mirror (ORVM)

Integrated exterior rear view mirrors on both the sides facilitate maximum rear view information to the driver.

Both the ORVMs are hinged and can be manually folded or unfolded. This avoids hindrances in narrow areas and parking slots. Make sure that you fully engage the mirror in its support, while folding or unfolding.

8.2.1 Tip-Tap ORVM Adjustment (if equipped)

Tip Tap ORVM’s can be adjusted by hand in the direction as indicated by the arrows. Adjust the mirror as required to bring the rear traffic vision as desired.

8.2.2 Manual (Joystick) ORVM Adjustment (if equipped)

Manual ORVM’s can be adjusted by the joystick provided on the ORVM trim. Adjust the joy stick as required to bring the rear traffic vision as desired.

8.2.3 Electric ORVM Adjustment (if equipped)

The electric exterior mirror adjustment switch is located on the RHS of instrument panel adjacent to the head lamp levelling switch. The joystick on the switch can be used to select the left/right mirror and also to adjust the respective mirror.

8.2.4 Electric Foldable ORVM (if equipped)

To open/fold the ORVM assembly rotate the Joystick anti-clockwise and hold for 2 sec.

8.3 Interior Mirror (IRVM)

The interior mirror has day and night (anti-glare) positions (if applicable). The night position reduces glare from head lamps of vehicles behind you. Flip the tab on the bottom edge of the mirror to select the day or night position.

8.4 Exterior Lamps

The lighting control stalk is located on the right hand side of the steering wheel. It controls operations of parking lamps, head lamps, head lamp beam selection, high beam flashing, fog lamps (if equipped) and turn signals when the ignition switch is ON.

8.4.1 Turn Signals

You can signal a lane change by moving the lighting control stalk clockwise or anti-clockwise to the limit point of free movement of the lever and releasing it once you change the lane.

8.4.2 Lamps OFF

Rotate the outer rotary switch on the lighting control stalk aligning the ‘dot’ on the switch to ‘OFF’ on the stalk to switch OFF all lamps.

8.4.3 Parking Lamps ON

Rotate the outer rotary switch on the lighting control stalk aligning the ‘dot’ on the switch to the ‘1st détente’ position on the stalk to switch ON the parking lamps.

8.4.4 Head Lamp ON

Rotate the outer rotary switch on the lighting control stalk aligning the ‘dot’ on the switch to the ‘2nd détente’ position on the stalk to switch ON the head lamps.

8.4.5 Head Lamp High Beam/Low Beam

With the head lamp low beam ON, push the lighting control stalk down (away) from steering wheel to switch ON the head lamp high beam. The head lamp high beam telltale lamp in the instrument cluster illuminates indicating high beam option selected. For low beam, pull the stalk back up.

8.4.6 Head Lamp Flash

Pull the lighting control stalk (from the head lamp low beam position) towards the steering wheel to instantaneously flash the head lamp high beam. The head lamp flash works even when the head lamp is OFF.

8.4.7 Head Lamp Leveling System

When the vehicle is either fully or partially loaded, it will have an upward inclination disturbing the head lamp aiming. A correct head lamp setting provides good visibility to the driver with minimum inconvenience to other road users.

To properly aim the head lamp beam as per the loading on the vehicle, use the head lamp leveling switch. This switch is located on the right side of the steering column shroud in the instrument panel. This switch has four positions marked as 0, 1, 2, & 3.

Select the suitable switch position depending on the pay load as advised in the table.

8.4.8 Power ECO Switch ( If Equipped)

Power ECO Mode helps you to improve the fuel efficiency of the vehicle. The switch is located on the driver panel switch bank, below the Head lamp levelling switch

Press the switch gently once to switch between modes. The ECO mode and Power mode is indicated by LED illumination separately in the switch.

Whenever vehicle is running in ECO mode, ECO lamp illumination in cluster will turn ON

8.4.9 Daytime Running Lamp (DRL)

• In day time whenever the engine is in running condition, DRL is enabled

• In day time whenever the engine is in running condition and park lamp is ON, DRL will get disabled

8.4.10 Magic Lamps (If applicable)

Magic lamps are greeting lamps which blinks to acknowledge to customer whenever he unlocks the vehicle using remote key.

Only Front Park LED will blink in the Specific Pattern (Ramp up, blink twice and ramp down) as feedback to RKE UNLOCK.

8.4.11 Hazard on Panic Braking

Hazard Lamps are turned ON during panic braking for 5 sec when the following conditions are met;

• Ignition is ON
• Vehicle speed is greater than 100 kmph
• Brake is applied
• Sudden High deceleration Rate

8.4.12 Fog Lamps (if equipped)

Fog lamps are to be used along with the head lamp low beam, to improve the vision during foggy and misty conditions.

Align the inner rotary switch on the lighting control stalk to the fog lamp off ‘dot’ on the inner fixed stalk as shown to switch OFF the fog lamps.

To switch ON the front fog lamps, switch ON the ignition and the parking lamps. Turn the inner rotary switch on the lighting control stalk to align to the fog lamp symbol on the inner fixed stalk as shown.

The front fog lamp indicator in the instrument cluster indicates the operation status.

8.4.13 Hazard Warning Lamp

The hazard warning lamp switch is located in between the AC center grills on the instrument panel. Use the hazard warning lamp when your vehicle is stationary or to warn other road users to be cautious while passing your vehicle.

To turn the hazard warning lamp ON, press the switch in. All the turn signal lamps flash. To turn OFF, press the switch again.

• Crash — Hazard would be turned on for 30 mins ( for vehicles equipped with airbags)
• Panic Braking — When the vehicle is running above 100 kmph and panic/sudden brakes are applied, hazard will turn on for 5 sec
• Vehicle break down warning bonnet open — The vehicle break down warning will be enabled only when bonnet switch changes from close to open condition at vehicle unlocked condition
  Pressing the hazard switch twice deactivates this feature.

8.5 Follow-Me Home (FMH) (if equipped)

This feature helps the driver and passengers to easily get out of the vehicle during poor light conditions. The head lamp low beam is turned ON for about 20 seconds, assisting the passengers to find their way unless cancelled by the UNLOCK signal from the RKE.

• Ignition transition from ON to OFF
• Park lamp is OFF
• Ignition key is out
• Double press RKE LOCK
• Head lamp low beam will turn ON for 20 seconds unless cancelled by the UNLOCK signal

• The first RKE LOCK command will be used for locking all doors
• Successive RKE LOCK commands will be used for toggling the current status of the head lamp low beam
• Each time FMH is extended, the head lamp low beam will be kept/turned on for the next 20 seconds
• If no extension is provided for 3 mins, FMH will get expired

• Ignition OFF to any other states
• Park lamp transition from OFF to ON
• RKE Unlock button is pressed
• RKE LOCK button pressed when Headlamp ON due to FMH
• FMH ON 20 seconds expires
• Max time of 3 mins has elapsed and no extension of FMH

With FMH mode ON, if the UNLOCK signal is received twice from RKE; the feature gets deactivated and cannot be extended further. Also, the doors are unlocked and vehicle disarmed.

8.6 Lead Me to Vehicle (LMV) (if equipped)

LMV is the feature that switches the head lamp ON in low beam for 20 sec helping the passengers to reach the parked vehicle safely and comfortably at night.

• Ignition key is out
• Park lamps OFF
• Press UNLOCK button twice on the RKE within 10 secs
• System will unlock all doors and disarm the vehicle followed by head lamp turning ON for 20 sec

• Successive UNLOCK commands received from RKE is used for toggling the current status of the head lamp low beam
• Each time LMV is extended the low beam will be kept/turned on for next 20 seconds

• LMV ON 20 seconds expires
• Ignition off to any other states
• Park lamp is switched ON
• LOCK command is received from RKE
• Max time of 3 mins has elapsed and no extension of LMV

8.7 Interior Lamps

Interior lamps comprise of Roof lamp and Theme lamp.

8.7.1 Roof Lamp

The Roof lamp is located in the roof above the front seats. The lamp can be switched on using the switch on the lamp.

Roof lamp — Auto Mode Operation

The Roof lamp switch has three operation modes to choose from;

A. The Roof lamp remains permanently ON in this position irrespective of the door open status

B. The Roof lamp remains in AUTO mode in this position.

C. The Roof lamp remains permanently OFF in this position

The operation of the Roof lamp in Auto mode is as follows;

• Roof lamp switches ON, If door OPEN status of any door when IGN is ON and Vehicle Speed is < 20 kmph
• Roof lamp switches ON when any of the doors is/are open
• Roof lamp switches ON, when Ignition is ON to OFF
• Roof lamp switches ON, when Battery Saver Time has not elapsed
• Roof lamp switches ON, when Crash status is Active from Airbag ECU
• Roof lamps dim and go OFF after a preset delay upon closing of all doors during IGN OFF condition
• Roof lamps dim and go OFF immediately on RKE lock or manual key lock after all doors are closed
• If any of the doors are not closed properly, then the Roof lamps switch OFF automatically after a preset duration (during IGN off) or once the vehicle speed > 20 kmph
• Roof lamps go OFF immediately with ignition ON and all doors closed properly

8.7.2 Mood Lamp (If equipped)

The Mood lamp give a Icy blue light ambience in the doors. They can be switched ON/OFF by the Mood switch on the roof bezel switch bank.

The Theme lamps are located at all door inner handles.

8.7.3 Boot Lamp (If equipped)

The Boot lamp is located in the rear luggage space area. This lamp will get switched ON when Boot or any doors are opened and switch OFF when it is closed.

8.7.4 Puddle Lamp (If equipped)

The Puddle lamp is located at the bottom of all doors. This lamp will get switched ON when door is opened and switch OFF when it is closed.

8.8 Power Outlet

There are two (on select variants) 12V power supply sockets provided for power take OFF depending on the vehicle variant. Electrical equipment/appliances like mobile phone charger, cigarette lighter, etc. can be used in the outlets. The power outlet is rated 12V/10A when the engine is ON.

The power outlets are located in the following places in the vehicle;

• Front - Below the HVAC control Panel

• Second Row (if equipped) - Rear right side of the second row seat back rest, on the RHS quarter trim

• Distract the driver while driving, or hamper safe driving
• Result in a fire or burn injuries due to the appliance rolling, falling or overheating
• Emit steam, while the windows of the passenger compartment are closed
• Never use the power outlet for electric heaters while sleeping
• Never insert foreign objects into the power outlet
• Never use malfunctioning electrical appliances
• Never insert inappropriate or badly fitting plugs into the power outlet

• Use the power outlets only when the engine is running. Remove the plug from the power outlet after using the electric device. Using the power outlets when the engine is OFF or leaving the electric device plugged in for many hours may cause the battery to drain
• Do not use the power outlet to connect electric accessories or equipment that are not designed to operate on 12V
• Some electronic devices can cause electronic interference when plugged into the power outlet. These devices may cause excessive audio noise and may interfere with other electronic systems or devices in your vehicle

8.9 Windshield Wipers

8.9.1 Wiper Control Stalk

The wipe/wash function can be activated only when the ignition is in “IGN” position.

8.9.2 Wiper Off

The wipe function is OFF when the wipe control stalk is in neutral position (B).

8.9.3 Flick-Wipe (Mist)

Push the wipe control stalk to position A for a flick-wipe, hold to operate the wipe continuously (simultaneously lift the wiper stalk towards the steering wheel to operate the wash). The stalk automatically comes back to position B when released.

8.9.4 Intermittent (INT) Mode

Intermittent (INT) wiping is selected when the wipe control stalk is pushed down to position C. In the INT mode, the wiper operates on preset intervals.

The delay between each wipe can be programmed from 1 to 60 sec according to the rain by the user.

Programming of the INT delay time is as follows;

• Turn the wiper stalk to position C, wiper will start wiping
• Turn the wiper stalk to OFF position, before wiper starts second wipe
• Turn the wiper stalk to position C again after the required delay and the same delay will be programmed
• On keeping wiper ON position C, the wiper will wipe again with the programmed delay

8.9.5 Low Speed Wiping

Push the wipe control stalk up to the position D to operate the wiper at a fixed low speed.

8.9.6 High Speed Wiping

Push the wiper control stalk up to position E to operate the wiper at a fixed high speed.

8.9.7 Rear Wiper (if equipped)

Rotate the outer rotary switch on the wiper control stalk to align the ‘dot’ on the switch to ‘ON’ symbol on the wiper stalk to operate the rear wiper.

8.9.8 Wipe/Wash

Pull/Lift the wiper control stalk towards the steering wheel from any position to activate the front wipe/wash function. Washer fluid is sprayed on the front windshield and the wipers wipe the windshield 3 times after the washer spray is stopped and wipe once after 4sec. Hold the stalk in position for continuous spray of washer fluid.

The rear windshield wash & wipe operates 3 to 4 times or as long as the stalk end is turned/rotated to wash détente. Wiping will continue for few seconds after releasing the stalk end switch.

Washer fluid is taken from the windshield fluid reservoir in the engine compartment.

In the front, a single nozzle with twin adjustable washer jets is provided on the bonnet. Using a pin, the eye ball jets can be adjusted precisely for direction. Always direct the washer jet to hit the middle of the windshield. This will enable the wiper blade to wipe the complete width of the windshield.

In the rear, a single nozzle with twin adjustable washer jets is provided on the top of the rear windshield. Adjust to direct the washer jet to hit the middle of rear windshield using a pin.

8.10 Utility Holders

8.10.1 Center Console (if equipped)

Center console is available in 5 seater variants between the front row seats. It has cup holders, and storage space for miscellaneous items like keys, pen, wallets etc.

8.10.2 Can/Cup/Bottle Holders (if equipped)

There are cup/can/bottle holders in the front middle seat & rear middle seat backrest(when using as armrest)and in the front/rear door trims.

The cup-holders on seat armrests are equipped with a flexible liner to better grip the cup/can being placed in it. This part can be removed for ease of cleaning in case of accidental spillage.

8.10.3 Storage Bin (If equipped)

Storage bin is located below the co-driver seat. This bin can also be removed and taken out while going for shopping/super markets.

To open, pull the strap provided on the co-driver seat bottom.

Lift the seat to access the storage bin

Storage bin can be taken out with the two handles provided.

8.10.4 Footwell Utility

The Footwell utility space is provided at the second row floor area.

To open, pull the strap provided on the lid of the utility.

8.10.5 Glove Box

The instrument panel houses a glove box on the passenger side.

The owner's manual can be found inside the glove box. It is advisable to always keep it in the glove box for ease of reach. It is also recommended to keep copies of all vehicle documents in the glove box for reference when needed. There is also a pen holder and card holder inside the glove box for convenience.

The Glove box houses a Chiller vent at the back side of the box.

By adjusting the knob up and down the vent can be opened or closed as required.

8.10.6 Sunglass Holder (If equipped)

Sunglass holder is located at the roof console. Press the lid to release the latch and lower the holder. It is strategically positioned to be accessed easily by both the driver and front passenger.

8.10.7 Sun Visor

The sun visors can be used for either frontal or sideward shade, to reduce glare or to shut out direct rays of the sun. The sun visor can be swivelled to the side, as shown, to provide shade from the glare of the sun.

A vanity mirror is provided on the back of the sun visor.

8.11 Horn

Press the pad on the steering wheel to sound the horn. The horn functions even when the ignition has been switched OFF.

8.12 Infotainment System

8.13 Radio Frequency ID (RFID) Tag

Your vehicle is fitted with a RFID tag as per CMVR regulations on front windshield.

RFID tag may be used for Electronic Toll Collection (ETC).

8.14 Instrument Cluster

8.15 Instrument Cluster Gauges

The instrument cluster comprises of the tachometer, speedometer, trip meter (A & B), SET button, MODE button, odometer, fuel gauge, coolant temperature gauge, warning lamps and telltale indicators.

8.15.1 Tachometer

The tachometer indicates the real time engine speed in thousands of RPM (revolutions per minute). Running the engine in very high RPM leads to excessive engine wear and poor fuel economy. Maintain steady engine speed below 2500 RPM and do not accelerate or decelerate abruptly.

8.15.2 Speedometer

The speedometer indicates the real time road surface speed of the vehicle in kilometers per hour.

8.15.3 Odometer/ Tripmeter

The bottom row of the LCD display gives the odometer reading. It records and displays the total distance traveled in kms.

The same display also gives the trip meter A & B details. It displays the distance travelled since the last trip reset. The two trip meters (A/B) can be reset by SET button.

8.15.4 Set and Mode Button

8.15.5 Engine Coolant Temperature Gauge

The engine coolant temperature bar graph functions only when the ignition is switched ON. It indicates the instantaneous engine coolant temperature. The coolant temperature varies with changes in weather, load on engine and driving pattern. LCD bar rises from Cold (C) towards Hot (H).

At normal operating temperature, 4 bars are displayed in the LCD bar graph. The high engine coolant temperature lamp along with 7 bars blink when the temperature reaches 110 o C with buzzer alert for 4 seconds, and when the temperature is 114 o C, the temperature warning lamp and all 8 bars are permanently ON. In such situations switch OFF the AC and observe any improvements in the temperature gauge. If not, stop the vehicle and allow the engine to cool down. Check the coolant level in the coolant reservoir and top-up if required. If the engine is still overheating, contact your nearest Authorized Mahindra Dealer.

8.15.6 Fuel Level Gauge

The fuel level bar graph functions only when the ignition is switched ON. It gives the status of the fuel level in the fuel tank. F indicates the tank is full (35 liters), E indicates the tank in empty. The amount of fuel required to fill the tank up may be less than the specified tank capacity, as a small amount of reserve fuel always remains in the tank.

When the tank is nearly full, 8 bars illuminate on the LCD bar graph display. When the tank is near empty i.e. RESERVE, the bottom bar alone is illuminated and the low fuel warning lamp in the cluster is ON.

On inclines or curves, due to the movement of fuel in the tank, the fuel level may fluctuate or the low fuel level warning lamp may illuminate earlier than usual. Always check the fuel level when the vehicle is on level road.

If the Low Fuel warning is continuous ON and If all 8 bars of Fuel indication are blinking than contact Mahindra Dealer.

8.15.7 Gear Position Display

Gear Indicator displays N,1,2,3,4,5,R, according to gear position during vehicle running and idling position. It will be displayed only when clutch is fully released. In case of reverse the gear indicator displays R until the vehicle is in reverse gear.

Indications will be displayed as:

8.15.8 Gearshift Indication

Gearshift Indication is a function which indicates to the driver the suggested optimal gear depending on the drive condition. The shift point is the maximum, after this there will be a penalty. Depending on the condition the shift points can be earlier than indicated. This information is visible on the LCD display integrated in the cluster

The gearshift indicator is indicated on the information display when the ignition switch is in the ON position.

• When the gearshift lever is in a position other than “N” (Neutral)

Lower gear position is selected for the vehicle speed or the engine revolution. Changing to a higher gear position is recommended.

Higher gear position is selected for the vehicle speed or engine revolution. Changing to a lower gear position is recommended.

The control system monitors driving condition and it shows which gear position is optimal for driving with the indication on the display.

If Up/Down arrow and the gear position other than currently selected are indicated on the display while driving, shift up or down the gear to the indicated position. It is the optimal gear position for driving condition.

8.16 Warning Lamps Overview

	Airbag warning lamp		EPS Malfunction Lamp		Low Oil pressure Lamp		Battery Charge Lamp		ABS warning Lamp		High Temperature Lamp
	Left indicator		Start Stop Lamp		Glow plug warning Lamp		Seat Belt warning lamp		Front Fog Lamp		Security lamp
	Right indicator		Check Engine Lamp		Low fuel warning lamp		ECO Lamp		Rear Fog Lamp		Park lamp
	Head Lamp High Beam		Door Ajar lamp		Park Brake/ Low Brake fluid / EBD malfunction Lamp		Water in fuel warning lamp		Malfunction Lamp

8.17 Warning Lamps in the Instrument Cluster

8.17.1 Malfunction (OBD) Lamp

The Malfunction (OBD) Lamp illuminates when the ignition is switched ON and remains ON till the engine has started indicating normal status. If the lamp remains ON, even after the engine is running then it indicates a potential engine malfunction.

• The fuel management system
• The emission control system
• Systems which affect emissions

Such malfunctions may result in excessive emissions. Contact an Authorized Mahindra Dealer immediately.

8.17.2 Check Engine Lamp

The check engine lamp illuminates when the ignition is switched ON and goes out in 3 seconds indicating normal status .If the lamp blinks or illuminates continuously then it indicates that there is a fault in the engine management system. Contact the nearest Mahindra Dealer for the necessary repairs.

8.17.3 Glow Plug Indicator

After Pre-check Glow plug indicator illuminates if required, It automatically goes OFF when the glow plug reaches the required temperature. Contact an Authorized Mahindra Dealer if the glow plug lamp does not illuminate with ignition ON or illuminates while driving.

8.17.4 Security Lamp

Once the ignition is turned OFF, the security lamp will blink at a fast rate frequency indicating the vehicle is secured against unauthorized start of engine. When the vehicle is locked using RKE, security lamp will blink at a slow rate frequency which will indicate that antitheft system is armed and unauthorized door entry to the vehicle will trigger alarm.

At ignition ON, the security lamp blinking continuously indicates a malfunction in the engine immobilizer system. Contact an Authorized Mahindra Dealer immediately.

8.17.5 Parking Brake/Low Brake Fluid /EBD Warning Lamp (if equipped)

The lamp illuminates when the parking brake is engaged or when the brake fluid level in the reservoir is low or when EBD (if equipped) failure is detected. If the lamp illuminates while driving, do the following:

• Check if the parking brake is engaged. If yes, disengage it
• Check if the brake fluid level is low. If yes, top-up brake fluid (DOT 4) to the required level

If the brake lamp still continues to illuminate, immediately get the vehicle checked at an Authorized Mahindra Dealer.

8.17.6 Turn Lamps

The turn lamp arrows in the instrument cluster flash showing the direction indicated by the turn signals. A sudden increase in the rate of flashing indicates failure of one or more of the lamp bulbs. Have them replaced as soon as possible.

8.17.7 Park Lamp

The Park lamp indicator illuminates whenever park lamp is switched ON through Combination switch. During ignition OFF if park lamp is ON with driver door open buzzer alert will be audible for 6 seconds.

8.17.8 Head Lamp High Beam Lamp

The head lamp high beam lamp illuminates whenever the head lamps are switched ON to high beam or when the head lamp flash is used.

8.17.9 Battery Charging System Warning Lamp

The battery charging system warning lamp illuminates when the battery is not being charged or when there is a malfunction in the alternator.

This lamp illuminates when the ignition is switched ON and goes out as soon as the engine is started. If the lamp continues to remain ON even after starting the engine, it is an indication that the battery is not being charged or there is a malfunction in the alternator. Check the alternator drive belt for looseness/breakage. If the drive belt is okay, switch OFF all unnecessary electrical equipment and recheck. Contact an Authorized Mahindra Dealer for further assistance.

8.17.10 Low Engine Oil Pressure Warning Lamp

The low engine oil pressure warning lamp illuminates when the ignition switch is turned ON and goes out as soon as the engine is started. If the lamp remains ON even after starting the engine, or illuminates while driving with buzzer alert, stop immediately and check the oil level after 2-3 minutes. If low, add engine oil to the ‘MAX’ level and check status. If problem persists, contact an Authorized Mahindra Dealer immediately.

8.17.11 High Engine Coolant Temperature Warning Lamp

The high engine coolant temperature warning lamp and 7 bars in the temp gauge blink when the coolant temperature reaches 110° C with buzzer alert for 4 seconds, and they remain permanently ON when the temperature reaches 114° C. Contact an Authorised Mahindra Dealer immediately.

8.17.12 Water-in-Fuel Warning Lamp

The water-in-fuel warning lamp illuminates when the accumulation of water in the fuel filter reaches the maximum permissible limit. The fuel filter needs to be drained. Contact an Authorised Mahindra Dealer.

8.17.13 Low Fuel Warning Lamp

Continuously ON-When the fuel level in the fuel tank falls to the reserve limit, the low fuel warning lamp is ON

Blinking- If the fuel level goes to empty state the lamp starts blinking. Refuel sufficiently and the lamp goes out. If the Low Fuel warning is continuous ON and If all 8 bars of Fuel indication are blinking than contact Mahindra Dealer.

8.17.14 Seat Belt Warning Lamp

The seat belt warning lamp blinking reminds the driver to fasten seat belt when the ignition is ON. After starting the engine, if driver seat belt is not fastened the seat belt buzzer alert will come for 6 seconds with seat belt lamp blinking. The lamp will continue to blink till the driver fastens the seat belt properly.

8.17.15 Airbag Warning Lamp

The airbag warning lamp in the instrument cluster illuminates when the ignition is switched ON and goes OFF in about 3 seconds. If the lamp remains ON continuously or flashes intermittently, contact an Authorized Mahindra Dealer immediately.

• Lamp fails to go OFF
• Lamp does not illuminate at all
• Illuminates while driving

Contact an Authorized Mahindra Dealer immediately when the airbag warning lamp indicates a system malfunction. The airbag may not deploy when needed, which could result in serious or fatal injury, or it might deploy unexpectedly and unnecessarily, which may result in personal injury.

8.17.16 Anti-lock Brake System (ABS) Malfunction Lamp

The ABS malfunction lamp illuminates when the ignition is switched ON and goes OFF after about 3 seconds. If the ABS malfunction lamp continues to remain ON or illuminates while driving, the ABS will not operate. But the brake system will still operate conventionally. In this condition, the wheels can lock during severe braking. Have the vehicle checked by an Authorized Mahindra Dealer as soon as possible.

8.17.17 EPS Warning Lamp

EPS warning lamp Indicates malfunction on Electric Power steering system. Contact an Authorized Mahindra dealer immediately.

NOTICE

When EPS is failed. vehicle can still be driven with increase in steering effort.

8.17.18 Front Fog Lamp

The front fog lamp telltale indicates the status of the front fog lamp. The front fog lamp can be switched ON only when the parking lamp is ON.

8.17.19 Rear Fog Lamp

The rear fog lamp telltale indicates the status of the rear fog lamp. The rear fog lamp can be switched ON only when the parking lamp is ON.

8.17.20 Door Ajar Warning Lamp

The door ajar warning lamp illuminates with buzzer alert for 4 seconds, when any door is open during ignition ON. The lamp goes OFF when all the doors are closed properly.

8.17.21 Start/Stop Lamp

The Start/Stop lamp blinks when the engine is about to be stopped by Start/Stop System. And the lamp turns ON continuously when the engine has been switched OFF by the System. On restarting engine by pressing the clutch/key, the lamp turns off.

The Start/Stop lamp blinks at faster rate for a longer time than usual when the battery state does not allow the system to stop the engine automatically.

8.17.22 ECO Lamp ( if available)

Whenever ECO switch is pressed in vehicle the ECO lamp will turn ON in Cluster and it will indicate that the vehicle is running in economy mode. If ECO switch is pressed but still ECO lamp is not turning ON or without pressing ECO switch if ECO lamp is ON, contact an authorized Mahindra dealer immediately.

8.18 Reverse Parking Assist System (RPAS)

Reverse parking assistance system is provided to aid the driver while parking the vehicle in reverse at a speed of less than 5 kmph. While reversing, RPAS will detect the obstacles at the rear side of the vehicle within the sensing zone, which cannot be viewed through the internal rear view mirror and the outside rear view mirrors. The RPAS will then alert the driver by a beep sound about the location of the detected obstacle and the distance from the vehicle. The alert sound level will vary proportional to the distance. Smaller the distance shorter the interval between the beeps.

Three RPAS sensors are located at the rear bumper to provide complete rear view to the driver for hassle free parking.

8.18.1 Driving and Operation

• The Vehicle should be in IGN ON state to activate the reverse parking assistance system.
• RPAS will be activate automatically when reverse gear is engaged and deactivate when reverse gear is disengaged.
• When the obstacles comes in the sensing range, the systems starts giving the indication based on the distance and direction of the obstacles as defined in the detecting zones. The closer the obstacles, more display bars illuminated & beeps alerts.
• On engaging the gear in reverse, the RPAS system gets activated automatically and the vehicle image appears in the infotainment screen. Display bars below the car image indicate the obstacles behind the vehicle
• When the obstacle comes in the sensing zone, the system starts giving the indication based on the distance and direction of the obstacle as defined in the detecting zones. The closer the obstacle, more display bars are illuminated

RPAS display on the infotainment screen gives the following information:

• Left zone indicates obstacle on the left hand side
• Center zone indicates obstacle in the center
• Right zone indicates obstacle on the right hand side

Display bars 1, 2, 3 and 4 indicate how close the obstacle is from the vehicle rear bumper, with bar 1 being very close and bar 4 being distant. The infotainment screen display’s a STOP! symbol if the obstacle is less than 50 cm from the vehicle rear bumper.

1. Start the vehicle (IGN is turned ON)

2. Change the gear to reverse (engage the reverse gear). The RPAS will be displayed on the infotainment screen.

   
3. Start moving the vehicle in the reverse direction
4. Display bars in the respective direction will glow according to obstacles in its path
   • If the obstacle is between 100 to 120 cm, bar 4 will be turned ON
   • If the obstacle is between 75 to 100 cm, bar 3 & 4 will be turned ON
   • If the obstacle is between 50 to 75 cm, bar 2, 3 & 4 will be turned ON
   • If the obstacle is less than 50 cm, all bars in that direction will be turned ON and a STOP! symbol will be displayed
5. Distance indicator will display the distance of the closest object
   NOTICE

   Value shown are approximate

6. The beep sound can be heard from the driver side speaker. Frequency of the beep will increase if obstacles comes closer (crossing each display bar) and the sound will be continuous if any of the obstacle is less than 50 cm
7. The RPAS distance displayed will be the minimum of distances sensed by left, center and right sensors and 120 cm is the maximum detection range.
8. Assume 3 obstacles are placed as mentioned below;
   • Obstacle at left at 74 cm
   • Obstacle at center at 66 cm
   • Obstacle at right at 52 cm

   Since obstacle is at 52cm in right -minimum distance is shown in the distance indicator

   On engaging the gear in reverse, infotainment will display as below. Along with this, a beep sound can be heard from the driver speaker. Frequency of the beep will increase if the obstacle comes closer and the sound will be continuous if any of the obstacles is less than 50 cm.

   

1. If the display bars in any one of the sides are displayed with cross marks, contact the nearest Authorized Mahindra Dealer.
2. If all display bars are displayed with cross marks, contact an Authorized Mahindra Dealer.
3. Obstacle in the blind zone cannot be sensed by the system.
4. Please check the condition of the obstacle behind your vehicle before reversing. In some cases, the display may be not as same as reality due to the installed sensor level, obstacle shape and reflection condition.
5. Point B will be detected sooner or later, but A may not be detected at all.
6. Not all obstacles are detected from 120 cm. For instance, a person is detected from 75 cm because of the weak reflection or absorption of the waves of the clothes.
7. The distance indication may move up and down due to different sizes of the obstacle at different positions.
8. Though the obstacle is in the sensing zone, obstacle may not be detected since the ultrasonic waves are not reflected back to the sensor
9. The obstacle of a conical shape may not be detected, since the ultrasonic waves get reflected away Limitations of RPAS
   • System may not sense obstacles like wire mesh, handrail, small objects which are below the bumper level.
   • System may not sense obstacles with cotton or spongy surface, which will absorb ultrasonic waves emitted by RPAS.
   • System performance is dependent on the reflection angle of the obstacle
   • System may give false alert with-out obstacles while reversing the vehicle on grasslands, gravels and bumpy roads considering it to be an obstacle.
   • System may give false signal while the vehicle moves from plain ground to a slope terrain vice versa.
   • System may give false signal by sensing the ground when the bumper is tilted more from the normal position or when the vehicle is heavily overloaded.
   • System may give false signal an alarm during heavy rain, snow and heavy wind conditions
   • Because of other ultrasonic sources, sensor may give false alarm for e. g., sweeping machines, high pressure steam cleaners and neon lights
   • Due to vehicle horns, motorcycle engines, air brakes of large vehicles, or other loud noises producing ultrasonic waves, the vicinity of the vehicle is noisy. it may cause sensor to give false alarm
   • The shape of the obstacle may prevent a sensor from detecting it. Some obstacles for example as follows

     - Sharply-angled objects

     - Tall or curved curb

     - Low obstacles ( with height of 40 cm above ground level)

     - Tall obstacles with upper sections projecting outwards in the direction of the vehicle

   • Depending upon the shape of the obstacle and other environmental factors, the detection distance may shorten or detection may be impossible
   • Obstacles may not be detected if they are too close to the sensor
   • System will not sense pot holes, trenches or drainages which are below the ground level.
   • Thin posts or objects lower than the sensor may not be detected when approached, even if they have been detected once

8.19 Engine Stop/Start System (ESS)

8.19.1 Overview of the ESS System

8.19.2 How Does the ESS Work?

Let’s take a simple example of driving in traffic conditions within your city. Assume that your vehicle has stopped at a traffic junction due to a red signal. The following steps illustrate how the system functions.

• The vehicle has come to a halt at a traffic signal, is in the neutral gear and the clutch pedal is released
• The ‘ESS’ lamp in the cluster will blink indicating that the engine is going to stop shortly. The engine will shut down automatically after a specific time period

• The ‘ESS’ lamp will illuminate in the instrument cluster indicating the engine was stopped by the ESS system.
• Once the signal turns green, press the clutch pedal and the engine starts immediately
• The indicator in the cluster goes OFF indicating that the engine has started again and you are ready to drive on

• ESS system is activated using the selection switch
• Bonnet is fully closed
• Fuel and Engine coolant temperature should be within the limits
• In the current ignition cycle, the vehicle has crossed 2 kmph at least once
• Current status of the engine is idling
• Vehicle speed is zero
• Accelerator pedal and clutch pedal are fully released
• Vehicle battery should be in healthy condition
• Engine is warm. This is an extra precaution to ensure safe working of the engine
• Gear is in neutral

• Vehicle should have been stopped by the ESS system
• Gear lever is in the neutral position
• Vehicle speed is zero
• ESS switch is in active mode
• Bonnet should be closed
• Clutch pedal is fully pressed (to restart)

8.19.3 Frequently Asked Questions (FAQ)

1. What is the advantage of this system?

   The ESS system aids in attaining better fuel efficiency of your vehicle and thus reducing your running costs. However, the mileage improvement will depend upon various parameters such as prevailing traffic, driving patterns, etc.

2. What are the other advantages of this system?
   
   • Since the engine is switched off during traffic signals/ jams, considerable amount of carbon dioxide release to the atmosphere is avoided. This reduces global warming and thus provides us with a sustainable planet to live in.
   • Ability to restart the engine by pressing the clutch pedal
   • Reduces noise pollution at traffic signals
3. Is it possible to start the engine through the clutch pedal for the first time?

   No, the engine can be cranked only with the ignition key for the first time. If the engine is stopped automatically by the system, only then it is possible to start the engine through the clutch

4. Whether the system will get activated as soon as the engine is started the first time with the ignition key?

   The system will get activated only after the completion of engine temperature dependent warm up period which may extend up to 15 minutes. This is to ensure better performance of the engine in terms of fuel economy and durability.

5. Are there any safety precautions to be followed?

   Yes, when the engine is turned OFF at traffic signals/jams with heavy electrical loads like head lamp or AC switched ‘ON’. If the duration of such stops are long, it is recommended to keep the engine ‘ON’ and the ESS system in ‘OFF’ position.

6. What is to be done, if I don’t want the system to stop my engine at traffic signals/jams?

   The system can be turned OFF by switching OFF the Stop/ Start selection switch.

7. Whether the A/C will function, if the engine is switched off?

   No, the A/C will not work. However the blower will be in operation when the ignition is ON.

8. What will happen if I keep the clutch continuously pressed at traffic signals/jams?

   The system will not stop the engine if the clutch is continuously pressed since it indicates the driver’s intention of moving the vehicle immediately.

9. When the battery charge is low, whether the engine will be switched off?

   If the battery charge drops below a certain level, the system will not stop the engine so as to preserve the battery from further draining.

10. Whether I will be able to operate the engine with the normal ignition key?

    Yes, normal operation with the ignition key is always possible.

11. Whether the vehicle will start (or) stop in gear?

    The vehicle will not start or stop automatically in gear to ensure safety. It will do so only in the neutral position of the gear shift lever.

12. Whether the system will stop my engine in moving traffic?

    No, the engine will be stopped only when the vehicle speed is zero continuously for more than 2 sec.

13. Whether the audio system will be switched OFF, when the engine shuts down?

    No, the audio system will not be switched OFF and you can continue to enjoy the music.

14. Whether the engine will re-crank whenever the clutch pedal is pressed?

    No, when the engine is running, the starter motor will not attempt to re-crank.

15. If any component involved in the system fails, what will happen?

    The system has a built-in diagnostic module which understands the failure and immediately goes to bypass mode. In the bypass mode the engine can be turned ON and OFF with ignition key as usual.

16. Are there any indications to show that engine does not stop due to poor battery charge state?

    Yes, if all other conditions except battery charge are met, the ESS lamp blinks faster for 7.5 seconds and the engine does not switch OFF.

9 STEERING AND BRAKES

9.1 Steering

Your vehicle is equipped with an Electric power steering system(EPS). There is no fluid reservoir to check or fill. EPS uses energy from the battery to decrease the driver's effort in steering the vehicle. The EPS system will give you good vehicle response and increased ease of maneuverability in tight spaces. If for some reason the power assist is interrupted, it will provide mechanical steering capability to steer the vehicle. Under these conditions, you will observe a substantial increase in steering effort.

• Never hold the steering wheel to the extreme right or the extreme left for more than a few seconds when the engine is running.
• During parking manoeuvre or continuous steering when vehicle is not in motion, the steering may appear to feel slightly stiff. This is not a malfunction; it is caused by a control system designed to prevent the motor from overheating. However, after a few minutes the steering wheel will return to its normal condition.

• Underinflated tyre(s) on any wheel(s)
• Uneven vehicle loading
• High crown in the center of the road
• High crosswinds
• Wheels out of alignment
• Wheels out of balance
• Loose or worn suspension components

9.2 Tilt Steering

The steering wheel can be adjusted for rake as required using the lever in the steering shroud under the steering wheel.

To tilt/adjust the steering wheel;

1. Ensure the vehicle is stationary and parking brake engaged
2. Pull the steering tilt lever down to unlock
3. Raise or lower the steering wheel to the desired position
4. Push the lever back up to its original position to lock the steering
5. Adjust the seat according to the steering wheel position

9.3 Steering Controls - Audio Control System (if equipped)

Audio control through the steering wheel switches/buttons helps the driver to operate the audio system from the steering wheel without losing concentration. The system has four switches which are mounted on the steering wheel.

• Press to change the source like radio, USB/iPod, Aux, and BT Audio.

• Radio: In Radio Source, Short press to change next/previous preset channel & long press to execute a Forward/backward frequency auto seek
• USB/ iPod : In USB/ iPod source, short press to change next/ Prev songs and long press to fast forward/backward Songs.
• AUX: No Action in SWC
• Bluetooth® function: In BT source, short press to change next/ Prev songs

• Short Press to accept an incoming call
• Short press to reject an incoming call

• Press the Mute button to mute the audio. Press again to Un-mute.

• To increase the volume by one point press the (+) button once. To decrease the volume by one point press the (—) button once.

9.4 Brakes

Your vehicle is equipped with disc brakes in the front and drum brakes in the rear.

Disc brakes offer good braking capability and reduced stopping distance. Wet brake discs result in reduced braking efficiency. After a car wash or driving the vehicle through water, dab the brake pedal while driving to remove the film of water from the brake pads. Brake pads feature mechanical wear indicator. When the brake pad is worn, metallic squeal noise is heard indicating the pad wear. Have them replaced immediately.

9.5 Parking Brake

Pull the parking brake lever as far as possible towards you.

For better holding power, first depress the brake pedal and hold it while applying the parking brake.

To release, turn the Lever clockwise and push it all the way forward.

To remind you that the parking brake is applied, the parking brake reminder light in the instrument cluster remains ON, until you release the parking brake and push it to the home position.

CAUTION

Do not attempt to release the Parking brake lever from top side. This may result in fingers get jammed with center console.

• The parking brake should be adjusted as per recommended maintenance schedule
• Always apply the parking brake when leaving the vehicle, and be certain to leave the transmission in gear, with the engine switched OFF. Failure to do so may allow the vehicle to roll and cause damage, hit a bystander resulting in personal injury.
• Leaving unattended children in a vehicle is dangerous for a number of reasons. Children should be warned not to touch the parking brake or the gear shift lever. Do not leave the key in the ignition. A child could move the vehicle leading to accidents
• The parking brake should always be applied when the driver is not in the vehicle.

Engaging the parking brake while the vehicle is in motion can cause the rear wheels to lock up. You could lose control of the vehicle and cause an accident.

9.5.1 Parking on a Hill/Incline

If you have to park facing uphill, select first gear and turn the front wheels away from the kerb. If you have to park facing downhill, select reverse gear and turn the front wheels towards the kerb. Always ensure the parking brake is engaged before leaving the vehicle.

9.6 Anti-Lock Brake System (ABS) (if equipped)

The Anti-lock Brake System (also called as ABS) is designed to help prevent lock-up of the wheels and stable stopping of vehicle during a sudden, panic emergency braking or braking on slippery road surfaces. The ABS system takes input from wheel speed sensors and brake pedal switch to control the brake fluid pressures at the wheels to avoid wheel lock-up. It allows vehicle to be steered during braking.

The minimum speed for ABS to function is 12 kmph. ABS is activated only during wheel lock conditions where ABS takes over and prevents wheel lock. During the ABS operation, a slight pulsation may be felt in the brake pedal to indicate ABS is active. You may also hear motor noise from the engine compartment. It is recommended to hold the brake pedal firmly while the ABS is active rather than pumping the brake pedal.

Depressing the brake pedal on slippery road surfaces as on a manhole cover, a steel plate at a construction site, a joint in a bridge, etc. on a rainy day, tends to activate the anti-lock brake system. The ABS warning lamp lights up when you switch ON the ignition and should go out after a few seconds. If the ABS warning lamp does not go out or if it comes ON while driving, it indicates there is a fault in the ABS system. Even if the ABS lamp comes on the normal braking system remains efficient, exactly as on a vehicle without ABS. However since the ABS functionality may be reduced when ABS lamp is ON the wheel locking can happen under wheel locking conditions, drive cautiously

The vehicle should be examined as soon as possible by an authorized Mahindra dealer. The Anti-lock brake system is not designed to shorten the stopping distance: Always drive at a moderate speed and maintain a safe distance from the vehicle in front of you. The stopping distance may be longer in the following cases:

• Driving on rough, gravel or snow covered roads.
• Driving with snow chains installed.
• Driving over steps such as the joints on the road.
• Driving on roads where the road surface is pitted or differences in surface height.

The ABS warning lamp lights up when you switch ON the ignition and should go out after a few seconds. If the ABS warning lamp does not go out or if it comes ON while driving, it means there is a fault in the ABS system. In both cases, the normal braking system remains efficient, exactly as on a vehicle without ABS. The vehicle should be examined as soon as possible by an authorized Mahindra dealer.

WARNING

Do not overestimate the Anti-lock Brake System: Although the Anti-lock Brake System assists in providing vehicle control, it is still important to drive with all due care and maintain a moderate speed and safe distance from the vehicle in front of you. There are limits to the vehicle stability and effectiveness of steering wheel operation even with ABS active. If tyre grip performance exceeds its capability, or if hydroplaning occurs during high speed driving in the rain, the Anti-lock Brake System will not assist with vehicle control.

10 HEATING, VENTILATION AND AIR-CONDITIONING SYSTEM (HVAC)

The climate control system enables you to set the cabin at the desired comfortable condition by controlling airflow, air intake and temperature control. The HVAC system also helps in defrosting and defogging/demisting the windshield and windows.

Engine coolant is utilized to heat the cabin air. For cooling cabin air, an air conditioning circuit based on the vapor compression refrigeration cycle is used. The air conditioning system uses a refrigerant along with a suitable lubricating oil. Though the refrigerant is non-ozone depleting, the refrigerant is a greenhouse gas. Hence we do not suggest the gas to be released directly into the atmosphere; it adversely affects the environment by contributing to global warming/climate change.

Multiple vents are provided for distributing the air, being force circulated by the HVAC blower, throughout the passenger compartment. Various ducts supply air from the HVAC unit to these vents having adjustable louvers.

10.1 HVAC Overview

10.2 Center/Side Vents

Two center vents are located above the audio system on the instrument panel and two side vents located one each at the left and right extreme ends of the instrument panel. Both the center and side vents provide air flow to the front seat passengers. Rotate the thumb wheel (B) up to open or down to close the air vent. Direct air to the desired direction by the adjusting louvers (A).

10.3 HVAC Controls

10.4 Air Distribution Control

The air flowing out of various vents can be controlled by the air distribution control knob/button.

• Face Mode — air is discharged from the center vents and side vents. This mode is most suitable for directing air flow towards the face of the passengers
• Face-Foot Mode — air is discharged from the center vents, side vents and foot vents. This mode is most suitable for directing air flow towards both the face and feet of passengers at the same time
• Foot Mode — air is discharged from the two foot vents . This mode is most suitable for directing air flow towards the feet of passengers seated on front seats. When it is in this mode, automatically the air intake will be in fresh air. This is because normally the foot mode is used with heater. At the same time, if the customer desires he can override manually and bring it to recirculation
• Foot-Defrost Mode — air is discharged from the foot vents, side defrost vents and windshield defrost vents. This mode is most suitable for directing air flow towards the feet of passengers while defrosting or demisting/defogging. When it is in this mode, automatically the air intake will be in fresh air. This is because normally the foot mode is used with heater. At the same time, if the customer desires he can override manually and bring it to recirculation
• Defrost Mode — air is discharged from the side defrost vents and windshield defrost vents. This mode is most suitable for directing air flow towards the front windshield to ensure defrosting or demisting / defogging. When it is in this mode, automatically the air intake will be in fresh air. This is because normally the foot mode is used with heater. At the same time, if the customer desires he can override manually and bring it to recirculation

10.5 Blower Speed Control

The blower force-circulates air through the HVAC unit and distributes it throughout the passenger compartment.

Blower is OFF when the blower speed control knob is set to small “o” position (extreme left). To switch-ON the blower, rotate the control knob clockwise which progressively increases the blower speed.

10.6 Temperature Control

By operating the temperature control knob, temperature of air being discharged from various vents can be adjusted to the desired level. Engine coolant is utilized to heat, whereas the air conditioner is used to cool the air inside the AC unit. Based upon selected position of the temperature control dial, the desired discharged air temperature can be obtained.

By rotating the dial counter-clockwise and setting it to the extreme left position, maximum cooling is obtained. When the dial is rotated clockwise, the discharged air progressively starts getting warmer and at the extreme right position, hot air is discharged. When the temperature control is in approximately two O’ clock position the air intake is automatically shifted to fresh air mode. This facilitates better functioning. At the same time if the customer is not comfortable , he can manually override and switch to recirculation mode

10.7 Air Intake Mode Control

The air intake control button toggles between fresh air or recirculated air modes.

To set the HVAC system to fresh air mode, keep the air intake control switch in the OFF condition. The lamp on this switch is OFF, indicating that the fresh air mode is active. In this mode, fresh air from outside the vehicle is sucked by the blower and utilized further to ventilate/cool/ heat the cabin.

To set the HVAC system to re-circulation mode, press the air intake control switch once. The lamp on the switch is ON, indicating that re-circulation mode is active.

In this mode, the air from inside the passenger compartment will be sucked by the blower and utilized further to ventilate/cool/ heat the cabin.

For quick cabin cooling/heating or while driving through dusty/ polluted regions, the recirculation mode can be selected. Driving with this mode active may lead to better fuel economy and longer HVAC filter life.

However, running the air conditioner in the re-circulation mode for long will make the cabin air too dry and the oxygen level drops inside cabin turning the air stale. On the contrary, keeping air intake control in the recirculation mode for long, with the air conditioner switched OFF, will make the cabin air too humid and the windshield/windows are more likely to fog.

10.8 Air-Conditioner ON

The air conditioning system can be switched ON/OFF by the “AC button” in the climate control system. A LED is also incorporated on the button to indicates the status. The air conditioner is operational only when both the engine and blower are running.

When the air conditioner is ON, air gets cooled and de-humidified before being circulated inside the cabin. In hot weather conditions, it will take slightly longer to cool the interior as compared to cooler weather. Fuel consumption will be relatively higher if the vehicle is being driven with the air conditioner.

1. Adjust the blower speed as required.
2. Select the air distribution mode as desired.
3. Select the air re-circulation mode if required.
4. Press the AC button to turn on the AC.
5. Adjust the temperature control dial as per the temperature requirement.

10.9 HVAC Air Filter (Cabin Air Filter)

Your vehicle’s HVAC system is equipped with two air filters (Primary & Secondary) at the blower inlet just behind the glove box. Before getting sucked-in by the blower, air passes through this filter element. Dirt and other foreign particles get trapped inside the filter. Clean air is then circulated through the HVAC unit and into the cabin.

The HVAC filter gets clogged after long use. The clogged filter will reduce the air flow rate, thereby the air-conditioning and heating efficiencies will be drastically reduced. Even the windshield/ windows may begin to mist/fog-up easily.

To maintain optimum HVAC system performance, Clean/Replace the filter element as per recommended maintenance schedule. However while operating in highly dusty or polluting conditions, the filter may require early replacement. If the air flow seems to have considerably reduced, get the filter cleaned immediately.

To access the Primary filter, open the glove box, remove the rubber pins on both sides of the glove box lid. Un-clip the filter retaining clip and remove the filter straight out. Clean the air filter or replace (if damaged) and follow the reverse procedure for putting the filter back.

To access the Secondary filter, open the glove box, remove the eight screws around the glove box and remove it. Un-clip the filter retaining clip and remove the top filter straight out. Then lift the bottom filter up and remove it. Replace the air filter as per maintenance schedule and follow the reverse procedure for putting the filter back.

10.10 Rapid Cabin Cooling

1. Make sure that all the windows are fully closed
2. Set the blower to maximum speed
3. Fully open the vents and adjust louvers to direct air toward face
4. Set the air distribution control to face mode
5. Set air intake control to recirculation mode
6. Turn the air conditioner ON
7. Set the temperature control knob to the extreme left (coolest) position

Once the passenger compartment reaches a comfortable temperature, shift to fresh air mode. Also blower speed and temperature control knob can be re-adjusted as desired.

10.11 Rapid Cabin Heating

1. Make sure that all the windows are fully closed
2. Set the blower to maximum speed
3. Set the air distribution control to foot mode
4. Set air intake control to recirculation mode
5. Set the temperature control knob to extreme right (hot) position
6. For dehumidified heating, switch the air conditioner ON

Once the passenger compartment reaches a comfortable temperature, the blower speed and temperature control knob can be readjusted as desired.

10.12 Defogging/Demisting and Defrosting

For keeping the front windshield and side windows clear, proper control of the HVAC system is essential. Follow the instructions in the subsequent sections to clear the frosted/misted/ fogged up front windshield.

10.12.1 Front Windshield Defog

1. Set the blower to full speed
2. Switch the air conditioner ON
3. Set the air distribution control to defrost mode
4. Select the fresh (outside) air intake mode
5. Adjust the temperature control knob to maintain comfort

10.12.2 Rear Windshield Demist (if equipped)

The rear windshield glass de—mist button is located in the AC control panel; as shown in the sketch. Press the button once to activate the demister. The LED on the button illuminates upon activation and the demister heats the rear windshield clearing the fog. Switch OFF the demister by pressing the button again as soon as the fog is cleared.

10.12.3 HVAC Controls — Electric Temperature Control

10.12.4 Air Distribution Control

The air flowing out of various vents can be controlled by the air distribution control knob/button.

Following are the five different distribution modes to choose from:

• Face Mode — air is discharged from the center vents and side vents. This mode is most suitable for directing air flow towards the face of the passengers
• Face-Foot Mode — It is activated by pressing the face and foot switch. Air is discharged from the center vents, side vents and foot vents. This mode is most suitable for directing air flow towards both the face and feet of passengers at the same time
• Foot Mode — air is discharged from the two foot vents . This mode is most suitable for directing air flow towards the feet of passengers seated on front seats. When it is in this mode, automatically the air intake will be in fresh air. This is because normally the foot mode is used with heater. At the same time, if the customer desires he can override manually and bring it to recirculation
• Foot-Defrost Mode — It is activated by pressing foot and front defrost switch. Air is discharged from the foot vents, side defrost vents and windshield defrost vents. This mode is most suitable for directing air flow towards the feet of passengers while defrosting or demisting/defogging. When it is in this mode, automatically the air intake will be in fresh air. This is because normally the foot-defrost mode is used with heater. At the same time, if the customer desires he can override manually and bring it to recirculation
• Defrost Mode — air is discharged from the side defrost vents and windshield defrost vents. This mode is most suitable for directing air flow towards the front windshield to ensure defrosting or demisting / defogging. When it is in this mode, automatically the air intake will be in fresh air. This is because normally the defrost mode is used with heater. At the same time, if the customer desires he can override manually and bring it to recirculation

10.12.5 Blower Speed Control

The blower force-circulates air through the HVAC unit and distributes it throughout the passenger compartment.

Blower is OFF when the blower speed control knob is set to small “o” position (extreme left). To switch-ON the blower, rotate the control knob clockwise which progressively increases the blower speed.

10.12.6 Temperature Control

By operating the temperature control switch, temperature of air being discharged from various vents can be adjusted to the desired level. Engine coolant is utilized to heat, whereas the air conditioner is used to cool the air inside the AC unit. Based upon selected temperature switch- Up/Down, the desired discharged air temperature can be obtained.

By pressing the down switch and setting all 3 Blue temperature control Led’s glow, maximum cooling is obtained. When the up switch is pressed , the discharged air progressively starts getting warmer and when all 3 Red temperature control Led’s glows, hot air is discharged. When the Red temperature control Led’s is glowing the air intake is automatically shifted to fresh air mode. This facilitates better functioning. At the same time if the customer is not comfortable , he can manually override and switch to recirculation mode

10.12.7 Air Intake Mode Control

The air intake control button toggles between fresh air or recirculated air modes.

To set the HVAC system to fresh air mode, keep the air intake control switch in the OFF condition. The lamp on this switch is OFF, indicating that the fresh air mode is active. In this mode, fresh air from outside the vehicle is sucked by the blower and utilized further to ventilate/cool/ heat the cabin.

To set the HVAC system to re-circulation mode, press the air intake control switch once. The lamp on the switch is ON, indicating that re-circulation mode is active.

In this mode, the air from inside the passenger compartment will be sucked by the blower and utilized further to ventilate/cool/ heat the cabin.

For quick cabin cooling/heating or while driving through dusty/ polluted regions, the recirculation mode can be selected. Driving with this mode active may lead to better fuel economy and longer HVAC filter life

However, running the air conditioner in the re-circulation mode for long will make the cabin air too dry and the oxygen level drops inside cabin turning the air stale. On the contrary, keeping air intake control in the recirculation mode for long, with the air conditioner switched OFF, will make the cabin air too humid and the windshield/ windows are more likely to fog.

10.12.8 Air-Conditioner ON

The air conditioning system can be switched ON/OFF by the “AC button” in the climate control system. A LED is also incorporated on the button to indicates the status. The air conditioner is operational only when both the engine and blower are running.

When the air conditioner is ON, air gets cooled and de-humidified before being circulated inside the cabin. In hot weather conditions, it will take slightly longer to cool the interior as compared to cooler weather. Fuel consumption will be relatively higher if the vehicle is being driven with the air conditioner

The following steps outline the procedure to switch ON the AC;

1. Adjust the blower speed as required.
2. Select the air distribution mode as desired.
3. Select the air re-circulation mode if required.
4. Press the AC button to turn on the AC.
5. Adjust the temperature control switch as per the temperature requirement.

10.12.9 Front Windshield Defog

1. Set the blower to full speed
2. Switch the air conditioner ON
3. Set the air distribution control to defrost mode
4. Select the fresh (outside) air intake mode
5. Adjust the temperature control switch to maintain comfort

10.12.10 Rear Windshield Demist (if equipped)

The rear windshield glass de — mist button is located in the AC control panel; as shown in the sketch. Press the button once to activate the demister. The LED on the button illuminates upon activation and the demister heats the rear windshield clearing the fog. Switch OFF the demister by pressing the button again as soon as the fog is cleared.

10.12.11 HVAC Points to Remember

• For quickly clearing the misted/fogged/frosted-up windshield, set the blower speed to maximum. For quick defrosting, set the temperature to extreme hot
• Once the windshield is cleared, keeping the air conditioner ON helps in keeping windshields and windows clear. Keep the fresh air mode selected. If required, re-adjust the blower speed and temperature control knob to maintain comfort.
• Driving the vehicle for long with glasses rolled up the air conditioner switched OFF may lead to windshield or windows getting misted/fogged up
• Driving the vehicle for long continuously in the recirculation mode may lead to windshield or windows getting misted/fogged up
• It is advisable to intermittently switch to FRESH air mode during long drives. Do not drive only in RECIRULATION mode continuously on long drives
• Do not blow cold air on the windshield and windows during humid weather. It could make windshield/windows mist/fog-up
• For defogging/demisting/defrosting the side windows at the front, select either Face or Face-Foot mode while directing air flow towards windows by adjusting the louvers of side vents. All other settings should be kept same as advised for windshield defogging/demisting/defrosting
• For heating the vehicle interior while windshield defogging/demisting/defrosting, select the Foot-Defrost mode. All other settings should be kept same as advised for windshield defogging/demisting/defrosting
• For fast defogging/demisting/defrosting the outside of the windshield, it is advisable to operate the windshield wiper/washer for a few times intermittently
• If snow has deposited on the windshield, use an ice scraper to remove the ice deposited before using the wiper
• In freezing weather, warm the windshield with the defroster before using the windshield washer. Also use a washer fluid with anti-freezing properties. This will help prevent the washer fluid from freezing on your windshield
• A dirty/contaminated windshield would make misting/fogging worse. Always keep the inside and outside of the windshield clean
• Reduced air flow because of a clogged HVAC filter or any other obstructions in the air flow path may lead to inadequate defogging/demisting/defrosting performance. If the air flow seems to have considerably reduced, get the filter cleaned/replaced immediately. The air flow path should be kept free of obstructions
• Reduced cooling performance from the air conditioner may lead to inadequate defogging/demisting/defrosting. If the cooling effect seems to have dropped considerably, get the air conditioning system checked by an Authorized Mahindra Dealer

11 STARTING AND DRIVING THE VEHICLE

11.1 Safety Tips - Before Starting your Vehicle

11.1.1 General

• Before starting the vehicle, inspect the inside and outside of the vehicle ; look for any damages, leaks, loose parts, foreign objects/debris. Contact an Authorized Mahindra Dealer if required.
• Before starting your journey, check the working of all safety devices/components especially brakes, steering, lamps, signals and tires. In case you suspect any system/devices not working properly contact Authorized Mahindra Dealer.
• Adjust the seat headrest, steering wheel and fasten the seat belt as described in this manual. Never perform any seat/ steering adjustments when the vehicle is in motion.
• Start the vehicle only when seated and belted in the driver's seat.

11.1.2 Mirror Adjustment

Ensure that the rear view mirror and both the ORVM’s are adjusted for an unobstructed view of the road behind.

11.1.3 Exterior Lamps

Have someone observe and confirm normal operation of all exterior lamps while you work on the controls from the driver seat. Also, check functioning of all lamps in the instrument panel.

11.1.4 Door Latches

Check for positive closing, latching, and locking of all doors, both from inside and outside.

11.1.5 Fluid Leaks

Check the area under vehicle after an overnight parking for fuel, power steering fluid, brake fluid, engine coolant, oil, or other fluid leaks. If leaks are observed, contact an Authorized Mahindra Dealer.

11.2 Ignition Switch

An illuminator ring is provided on the face of the ignition switch to help in locating the ignition switch at night. The ring will illuminate the moment the driver door is opened and will remain glowing till the driver door is closed.

LOCK — This is the ignition and steering lock position. The vehicle circuits and engine are completely switched OFF. The steering wheel is also locked and the key can be removed from the ignition only in this position.

ACC — The steering is unlocked and can be rotated. In this position all electrical circuits are enabled. Use this mode when you want to listen to music, etc., with the engine temporarily switched OFF.

ON — All electrical circuits are enabled. Some of the warning or information lamps illuminate in this position. While some of the lamps will go out after a few seconds, some will continue to remain ON till the engine is started. When the vehicle is being driven, the ignition switch remains in the IGN position.

11.3 Pedals

11.4 Starting the Engine

Make sure all vehicle occupants are properly seated in their seats and have buckled their safety belts. For more information on seat, headrest positioning, safety belts and their proper usage, refer to the “Seat Belts” section in this manual.

1. Shift the gear shift lever to neutral position.
   CAUTION

   When the vehicle is on gear, 90% of the clutch to be pressed for starting the engine.

2. Apply parking brake.
3. Turn the ignition ON.
4. Do not press the accelerator.
5. Turn the key momentarily to the START position to crank the engine
6. Once the engine starts, release the key; it will return to the IGN position
   CAUTION

   Do not continue cranking after the engine has started. This will lead to damage of the starter and other engine components.

7. If the engine fails to start, attempt to restart after about 10 seconds
8. If the engine fails to start even after repeated attempts as per the procedure given above, contact the nearest Authorized Mahindra Dealer
CAUTION

To prevent damage to the starter, wait 10 seconds before attempting to restart the engine.

If the engine still fails to start, contact an Authorized Mahindra Dealer for assistance.

The idle speed is controlled automatically and it will decrease as the engine warms up.

• All warning lamps are OFF
• Low oil pressure lamp is OFF

After idling for a few seconds, release the parking brake, depress the clutch, shift the gear shift lever to 1st gear, release the service brake pedal, drive by releasing the clutch and depressing the accelerator pedal simultaneously.

11.4.1 Engine Idling - In Cold Weather

Avoid full throttle operation when the engine is cold and prolonged idling at low ambient temperatures. Long periods of idling may be harmful to your engine. Combustion chamber temperatures can drop so low that the fuel may not burn completely. Incomplete combustion allows carbon and varnish to form on piston rings and injector nozzles. Also, the unburned fuel can enter the crankcase, diluting the oil and causing rapid wear to the engine.

11.5 Stopping the Engine

Before turning the engine OFF, always allow the engine to return to normal idle speed and run for few seconds. This assures proper cooling and lubrication of the turbocharger. This is particularly necessary after any hard driving.

• Keep your right foot on the service brake pedal
• Turn front wheels towards the road curb
• Switch OFF the ignition, turn the key to the steering lock position and remove the key
• Firmly engage the parking brake
• Move the gear shift lever to 1st gear position (reverse gear if parking on an incline)
• Slowly release the service brake pedal
• Lock your vehicle when leaving

11.5.1 Over Speed Warning

When the vehicle crosses the preset speed value, buzzer alert will be audible for 4 seconds.

11.6 Manual Transmission

The first few shifts on a new vehicle may be somewhat notchy. This is a normal phenomenon, and smooth shifts will develop within the initial few hundred kilometers of running.

11.6.1 Gear Shift Lever

The gear shift lever shifts the transmission into various gears. The gearshift pattern is shown on the gear lever knob. The clutch pedal should be depressed fully while shifting, and then released slowly.

With the gear shift lever in neutral and brakes released, the vehicle can move freely by pushing or towing. The engine can be started in this mode. It is always recommended to keep the brake pedal depressed in this position. It is advisable to shift into neutral when the vehicle is at a standstill for longer durations with the engine idling.

Forward — Use the gears 1 to 5 as per vehicle load, road/traffic conditions or as per requirement.

Reverse — This gear is to enable the vehicle to move in the reverse direction. Move the gear shift lever into this position only after the vehicle has come to a complete stop.

To prevent the engine from laboring at a low RPM when driving uphill gradients or with your vehicle heavily loaded, downshift when necessary to maintain engine RPM within the best torque range. Similarly while driving downhill, downshift to utilize the engine braking in an optimum manner.

11.6.2 Recommended Gear Shifting Speeds

Always depress the clutch fully before moving the gear shift lever from the current position to any desired position. Perform up-shifts or down-shifts one gear at a time, do not jump gears.

11.7 Driving Your Vehicle

11.7.1 General Driving Precautions

• Before you drive your vehicle, please read this manual carefully.
• Before you start driving, check proper operation of the brakes and steering system.
• If, while driving, you hear any strange noise or feel unusual vibration, or if you have any concerns whatsoever, or if any warning lamps illuminate or buzzers sound, park/stop the vehicle in a safe location as soon as possible. Identify the cause and take any necessary remedial action. Contact your Authorized Mahindra Dealer if necessary.
• Never overload or improperly load your vehicle.
• Always be attentive while driving and follow safe driving practices.
• Always maintain the recommended inflation pressure in tires.
• Always drive at a safe speed appropriate for given driving conditions. You must follow the speed limits.
• While backing up, keep a constant lookout for people, particularly children, or other obstructions or hazardous material that might be present behind the vehicle.
• Avoid loading any items on the roof that will raise the vehicles center of gravity and make your vehicle more unstable.
• Loaded vehicles, with a higher center of gravity, may handle differently than unloaded vehicles. Extra precautions, such as slower speeds and increased stopping distance, should be taken when driving a heavily loaded vehicle.
• Always slow down in gusty crosswinds. Because of its profile and higher center of gravity, your vehicle is more sensitive to side winds than an ordinary passenger car. Slowing down will allow you to have much better control.
• When driving off-road or on rugged terrain, do not drive at excessive speeds, jump, make sharp turns, strike objects, etc. This may cause loss of control or vehicle rollover causing serious injury. You are also risking expensive damage to your vehicle's suspension and chassis.
• Maintain steering wheel control at all times, especially on rough terrains. Sudden changes in terrain can result in abrupt steering wheel motion. Make sure you grip the steering wheel from the outside. Do not grip the spokes.
• If the vehicle goes from one type of surface to another (e.g. from concrete to gravel/sand/mud/snow) there will be a change in the way the vehicle responds, especially the way it responds to steering, braking and accelerating inputs.
• Be extremely careful when driving on pavements made slippery by loose sand, water, gravel, snow or ice.
• If your vehicle goes off the edge of the pavement, slow down, but avoid severe brake or steering application. Ease the vehicle back onto the pavement only after reducing your speed. Do not turn the steering wheel too sharply while returning to the road surface.
• It may be safer to stay on the apron or shoulder of the road and slow down gradually before returning to the pavement. You may lose control if you do not slow down or if you turn the steering wheel too sharply or abruptly.
• In an unavoidable emergency situation where a sudden sharp turn must be made, turn the steering wheel only as rapidly and as far as required to avoid the emergency. Excessive steering will result in less vehicle control. Additionally, smooth variations of the accelerator and/or brake pedal pressure should be utilized if changes in vehicle speed are called for. Avoid abrupt steering, acceleration or braking which could result in an increased risk of loss of vehicle control, vehicle rollover and/or personal injury. Use all available road surfaces to return the vehicle to a safe direction of travel.

11.7.2 Off Road Driving Precautions

• When driving off-road or on rugged terrains, never overspeed or make sharp turns. This may cause loss of control or vehicle rollover causing serious injury.
• Maintain steering wheel control at all times. Sudden changes in terrain can result in abrupt steering wheel motion.
• Do not drive horizontally or diagonally across steep slopes, your vehicle can tip over sideways. Driving straight up or straight down is preferred.
• Drive cautiously to avoid vehicle damage from concealed objects such as rocks and stumps. You should either know the terrain or map-out your route before driving in the area.
• Always perform a maintenance inspection after each day of off-road driving that has taken you through rough terrain, sand, mud or water.

11.7.3 Driving Through Water

Although your vehicle is capable of driving through shallow water, there are a number of precautions that must be considered before entering the water.

• The ground under the water might not be firm which could result the water being deeper than expected when driving the vehicle through it.
• Do not stop or shut OFF the engine while immersed in water. It helps in preventing water getting inside the exhaust pipes.
• When backing down a ramp, do not allow the exhaust tail pipe to immerse in water.
• Water can wash the grease from wheel bearings, causing rusting and premature failure. It may also enter the differentials, transmission and transfer case, reducing the oil's lubricating qualities. If these are submerged in water, the lubricants should be replaced as required.
• Water entering the transmission will cause deterioration in shift quality, locking up of your transmission accompanied by vibration, and ultimately damaging the transmission.
• Sand, mud/sludge that has accumulated in brake drums and around brake discs may affect braking efficiency. This may also damage brake system components. Wet brakes cannot stop the vehicle as effectively as dry brakes. Drying can be improved by driving the vehicle slowly while applying light pressure on the brake pedal.
• When driving through water, traction or brake capability may be limited. Always perform a maintenance inspection after each day of off-road driving that has taken you through water.

11.7.4 Flowing Water

If the water is swift flowing and rising (as in storm run-off) avoid crossing until the water level recedes and/or the flow rate is reduced.

The flowing water can erode the streambed causing your vehicle to sink into deeper water.

Determine the exit point(s) that are downstream of your entry point to compensate for drifting.

11.7.5 After Driving Off-road or through Water

Off-road operation puts more stress on your vehicle than does most on-road driving. Always perform a maintenance inspection after each day of off-road driving that has taken you through rough terrain, sand, mud, or water.

• After going off-road, it is always a good idea to check for damage. Completely inspect the underbody of the vehicle for any damages.
• Check for accumulations of plants or bushes. These could be a fire hazard. They might also hide damage to fuel lines, brake tubes/hoses, etc.
• Inspect all the tubes/hoses and check for any fluid leakages.
• Get heat exchangers (radiator and condenser) cleaned.
• Check threaded fasteners for looseness, particularly on the chassis, drive train components, steering, suspension and brakes. Retighten them, if required, and torque to the values specified in the ‘Repair Manual’.
• We also recommend that the vehicle be checked at the Authorised Dealer for any water entry into the transmission/ axle or the engine

• If any unusual vibration is experienced, check the wheels for impacted material. Impacted material can cause a wheel imbalance. Get it inspected/corrected as soon as possible.
• After driving through deep water, inspect your vehicle fluids and lubricants (engine oil, transmission/transfer case/axle oils) to ensure the fluids have not been contaminated.

11.8 Fuel

For Diesel variant - Use commercially available vehicular Ultra-low Sulfur Highway Diesel that meets the Indian Standard (IS 1460; 2010 BS IV specification or equivalent). Information on diesel quality can normally be found in the fuel pump. Please contact any filling station personnel in case labels in the pump cannot be found.

For Petrol variant - Use commercially available Petrol fuel confirming to Indian Standard (IS 2798; 2010 BS IV / BSIII specification or equivalent). Information on Petrol quality can normally be found in the fuel pump. Please contact any filling station personnel in case labels in the pump cannot be found.

During freezing weather if the fuel is not winterized or is insufficiently winterized, waxing/gelling may take place in the fuel, leading to interruption in fuel supply to the engine. For smooth functioning and reliable operation of the engine during cold weather conditions, use winterized ULSD which is available at the filling stations during winter months. Check with your fuel retailer for further details.

Avoid inhaling fuel vapors and any skin or clothing contact. Direct skin contact with diesel/Petrol or the inhalation of fuel vapor may affect your health.

It is recommended maintaining a minimum of 10 liters of fuel in the fuel tank. Driving the vehicle till the fuel tank is empty is not recommended. Always have sufficient fuel in the tank. Check the fuel level prior to starting your journey.

11.8.1 Fuel-Lid Opening and Closing

The fuel-lid can be opened by the lever located at the foot of the driver seat. Lift the lever up firmly to open.

Turn the fuel cap counter-clockwise to open. Refuel and put the cap back in its place and tighten in the clockwise direction till three distinct clicks are heard. Close the fuel lid shut.

11.9 Tips for Better Fuel Economy

Give due consideration to the points listed below for better performance of vehicle and enhancement of fuel economy.

• Smooth, moderate operation will yield savings in fuel
• Steady speeds without stopping will usually give the best fuel economy
• Ensure that the parking brake is fully released
• Idling for long periods of time will waste fuel
• Anticipate stopping; slowing down may eliminate the need to stop
• Sudden or hard accelerations reduce fuel economy
• Slow down gradually
• Drive at moderate speeds
• Revving the engine before turning it off may reduce fuel economy
• The air conditioner may reduce fuel economy
• Warming up a vehicle in neutral on cold mornings is not required and may reduce fuel economy
• While idling put the gear shift lever in the neutral position
• Resting your foot on the clutch pedal while driving will reduce fuel economy
• Combine errands and minimize stop-and-go driving
• Keep tires properly inflated. It is recommended to check your tire pressure in the morning when the tyre is cold
• Use recommended engine oil. Refer to the Maintenance Section for specifications and capacities
• Replace the fuel filter and air filter at the recommended intervals
• Shift gears at the recommended speeds and rpm bands only. Refer to the gear shifting speed table for further details
• Control the maximum speed between 90 to 100 kmph in 5th gear to achieve the best fuel efficiency
• Follow the recommended maintenance schedule and perform the owner maintenance checks recommended
• Heavily loading a vehicle or towing a trailer will reduce fuel economy
• Carrying unnecessary weight may reduce fuel economy
• Adding certain accessories to your vehicle may reduce fuel economy
• Four-wheel-drive operation (if equipped) is less fuel efficient than two-wheel-drive operation
• Driving on flat terrains offer improved fuel economy as compared to driving on hilly terrains
• Close windows during high speed driving for better fuel economy
• It is recommended to refuel in the mornings (cold weather condition)

11.9.1 How to Calculate Fuel Efficiency (Mileage)

1. Ensure recommended tire pressure is maintained
2. Refuel your vehicle till the fuel gun at the fuel station is auto-cut-off
3. Reset trip meter to zero
4. Drive at a moderate speed for a minimum distance of 150 km
5. Refuel at the same fuel station till the auto-cut-off mode
6. Assuming ‘a’ liters of fuel was filled and ‘b’ was the trip meter reading. Fuel Efficiency = b/a kmpl
7. We recommend that point no.2 and point no.5 should be done in cold conditions (In mornings)

12 WHEELS AND TYRES

12.1 Tyre Information

12.2 Tyre Rating

Your vehicle is originally equipped with tyres supplied by a reputable manufacturer. If you ever have any questions regarding your tyres, please refer to literature supplied by the tyre manufacturer, or to the separate tyre warranty provided by the tyre manufacturer. You may also contact Mahindra directly, or the tyre manufacturer.

The tyre rating of your vehicle is;

• 185/65 R14 86 T

Tyre rating is explained as below;

(A):185 (Three-digit number):This number gives the width in millimeters of the tyre from sidewall edge to sidewall edge. This is called ‘Section Width’.

(B):65 (Two-digit number):This number, known as the aspect ratio, gives the tyres ratio of height to section width.

(C):R This is the tyre Construction Code. The ‘R’ stands for Radial.

(D):14 (Two-digit number):This number is the wheel or rim diameter in inches.

(E):86(Two or three digit number):This number is the tyres load index. It is a measurement of how much weight each tyre can support.

(F):T tyre speed rating or speed symbol. Never drive the vehicle faster than the tyre speed rating. The speed rating denotes the speed at which a tyre is designed to be driven for extended periods of time under a standard condition of load and inflation pressure. The ‘H’ stands for MRF. The ‘T’ stands for Bridgestone.

12.2.1 Speed Rating

12.3 Tyre Label (Vehicle Placard)

The tyre Label (Vehicle Placard) is located on the driver door B pillar inner edge/face. This placard gives you important information about the tyre size designed for your vehicle, and the tyre inflation pressures for the front and rear tyres.

12.4 Tyre Pressure

Proper Tyre inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tyre pressure;

• Safety
• Economy
• Ride Comfort and Vehicle Stability

Proper tyre inflation contributes to a comfortable and safe ride. Overinflating produces a jarring and uncomfortable ride. Both underinflation and over inflation affect the stability of the vehicle; induce the perception feeling of hard steering or over responsiveness in the steering. Unequal tyre pressures can cause erratic and unpredictable steering response or may cause the vehicle to drift left or right and uncomfortable ride.

Improper inflation pressures can cause uneven wear patterns to develop across the tyre tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tyre replacement. Underinflation also increases tyre rolling resistance and results in higher fuel consumption.

12.4.1 Inspection and Adjustment Procedure

The tyre pressure should be checked and adjusted, as well as inspected for signs of tyre wear or visible damage, at least once a month. Use a good quality pressure gauge to check tyre pressure. Do not make a visual judgement when determining proper inflation. Radial tyres may look properly inflated even when they are underinflated. At the same time, each tyre should be inspected for signs of tyre wear or visible damage.

Inflation pressures specified on the placard are always cold tyre inflation pressures.It is better to check the tyre pressure in morning when the vehicle is not driven for more than 1 to 2 Km. Cold tyre inflation pressure is defined as the tyre pressure after the vehicle has not been driven for at least three hours, or driven less than 1 km after a three-hour period. Check tyre pressures more often if subject to a wide range of outdoor temperatures, as tyre pressures vary with temperature changes. tyre pressures change by approximately 1 psi (7 kPa) per 7°C of air temperature change. Keep this in mind when checking tyre pressure inside a garage, especially in the winter.

When it was new, the spare tyre in your vehicle was fully inflated. However, a spare tyre can lose pressure over time. In order to avoid getting stranded, check the spare tyre air pressure frequently.

12.4.2 Inflating Your tyres

Safe operation of your vehicle requires that your tyres are properly inflated. Remember that a tyre can lose up to half of its air pressure without appearing flat.

At least once a month or before long trips, inspect each tyre and check the tyre pressure with a tyre gauge (including spare tyre). Inflate all tyres to the recommended inflation pressure.

Tyres with correct pressure help in improving the fuel efficiency. Besides improving the tyre life

Always inflate your tyres to the recommended pressure even if it is less than the maximum inflation pressure information found on the tyre. The recommended tyre inflation pressure is found on the tyre Label which is located on the front passenger side inner B-pillar. Failure to follow the tyre pressure recommendations can cause uneven tread wear patterns and adversely affect the way your vehicle handles.

12.4.3 Radial Ply tyres

12.4.4 Tread Wear Indicators (TWI)

Tread wear indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 inch (1.6 mm). When the indicators appear in two or more adjacent grooves, the tyre should be replaced.

12.4.5 Life of tyre

The service life of a tire is dependent upon various factors including but not limited to;

• Driving style
• tyre pressure
• Distance driven

12.4.6 Snow Chains

Snow chains cannot be used on these tyres.

12.5 Tyre Rotation Recommendations

Tyres on the front and rear axles of vehicles operate at different loads and perform different steering, handling, and braking functions. For these reasons, they wear at unequal rates and develop irregular wear patterns.

Rotation will increase tread life, help to maintain mud, snow, and wet traction levels, and contribute to a smooth, quiet ride. Follow the recommended tyre rotation frequency for your type of driving.

It is recommended rotating the tyres as per the “Maintenance Schedule”.

The suggested rotation method is the “forward-cross” shown in the diagram. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on On/Off-road type tyres.

Rotation will increase tread life, help to maintain mud, snow, and wet traction levels, and contribute to a smooth, quiet ride. Follow the recommended tyre rotation frequency for your type of driving. More frequent rotation is permissible if desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being performed.

12.5.1 Changing a Flat tyre

Refer to “If you have a Flat tyre” section in the general chapter for details.

12.5.2 Wheel Tightness

When you change a wheel, remove all rust and dirt at all locations where the wheel contacts the wheel hub. Use a scraper or wire brush to be sure that you remove all rust and dirt. A loose wheel could have damaged or elongated the holes in the rim, or damaged the rim/hub assembly. If any of the wheel studs or nuts are damaged, contact the nearest Authorized Mahindra Dealer.

13.1 Hazard Warning Lamp

The hazard warning lamp switch is located in between the two AC center vents on the instrument panel. Use the hazard warning lamp when your vehicle is stationary or to warn other road users to be cautious while passing your vehicle.

To turn the hazard warning lamp ON, press the switch in. All the turn signal lamps flash. To turn OFF, press the switch again.

• Crash — Hazard would be turned on for 30 mins
• Panic Braking — When the vehicle is running above 100 kmph and panic/sudden brakes are applied, hazard will turn on for 5 sec
• Vehicle break down warning bonnet open — The vehicle break down warning would be enabled only when bonnet switch changes from close to open condition at vehicle unlocked condition

Pressing the hazard switch twice deactivates this feature.

13.2 Vehicle Does Not Start - Checks

Before making these checks, make sure you have followed the correct starting procedure and that you have sufficient fuel.

1. Check that the battery terminals are tight and clean.
2. If the battery terminals are firmly fastened, switch ON the interior lamps.
3. If the lamps do not illuminate, glow dim or go OFF when the starter is cranked, then it indicates a weak or discharged battery. Try jump starting. Follow ‘Jump starting’ instructions given later in this chapter.
4. Check the fuses in the Engine Compartment Fuse Box and Central Fuse Box.

1. If the lamp illumination is normal, engine is cranking normally, but the engine does not start even after repeated cranking, it needs adjustment or repair. Contact an Authorized Mahindra Dealer.
2. During winter, use non-winter diesel or due to extreme cold conditions, the vehicle may not start. Contact an Authorized Mahindra Dealer for further assistance.
   CAUTION

   To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again.

Reduce your speed gradually, keeping a straight line. Move cautiously off the road to a safe place. Turn ON your hazard warning flashers and check for any malfunction lamps in the instrument cluster. Turn the ignition OFF, wait for approximately 90 seconds and try starting the engine again. If the vehicle still does not start contact an Authorized Mahindra Dealer.

If the engine speed does not increase when the accelerator pedal is depressed, there may be a problem in the Engine Management System, electrical or electronic controls. In case of certain faults, the engine may go to limp home mode, which is indicated by the check engine lamp. Have your vehicle checked by an Authorized Mahindra Dealer as soon as possible.

13.3 Vehicle Overheating

If the needle in the temperature gauge in the instrument cluster is all the way up to the H and/or the high engine coolant temperature warning lamp is ON, your engine has overheated.

If the engine is getting overheated, the Engine Management System reduces engine power substantially and may even shut the engine OFF; it is dangerous to continue driving when the engine has overheated. You need to first cool the engine down before starting to drive again.

Follow the below instructions to cool the engine down

• Progressively reduce the vehicle speed and bring the vehicle to a stop at the side of the road
• Turn ON the hazard warning flashers
• Keep the engine running at idle
• Engage the parking brake
• Switch off the air conditioner
• Wait till the engine coolant temperature drops sufficiently such that the needle in the temperature gauge is around halfway between C and H

Now switch the engine OFF and carefully open the bonnet/hood to visibly inspect the engine cooling system parts. Be cautious while doing an inspection as vehicle parts will still be too hot. Verify that the engine coolant level in the coolant recovery tank is maintained between the 'Min' and 'Max' mark. Check for possible fluid leakages. Check for damages to heat exchangers and connecting hoses. Also verify that the radiator shrouds, engine fan blades and the engine belt all are in good condition.

If any evidence of failure is observed, contact the nearest Authorized Mahindra Dealer for help. In case, no system leakage/ failure is suspected, driving can be continued.

Either due to severe operating conditions or due to any system leakages or failures, the engine can get overheated. However if the engine is getting overheated repeatedly, even in normal operating conditions, get the vehicle checked by an Authorized Mahindra Dealer as soon as possible.

13.4 Jump Starting

If your vehicle's battery has run down, you may be able to start the engine by using a standalone booster battery or a vehicle with a good condition battery.

But before going ahead with this procedure ensure that the battery is the cause of vehicle not starting. To confirm this, few simple tests can be conducted as follows;;

• Check the headlights - Are they dim or bright? If they are dim, it's likely your battery is dead. If your headlights are bright, you do not have a dead battery and a jump start may not help
• Try to start your vehicle -Does it turn over very slowly, or does it crank quickly? If it cranks quickly, you do not have a dead battery and a jump start may not help. If it cranks slowly, or not at all, you probably have a dead battery

Open the bonnet and locate the battery (near the left side fender). Identify the positive and negative terminals.

• The positive terminal will be marked with a plus sign (+) and will usually have a RED cable attached on it.
• The negative terminal will be marked with a minus sign (-) and will usually have a BLACK cable attached to it

Check the physical condition of the battery. Inspect batteries for cracks, leaks or any other damage. If you find any of these things, do not jump start the vehicle. Call Mahindra Road Side Assistance or replace the battery. If the weather is very cold, remove the refill caps and check the condition of the electrolyte. If it seems slushy or like ice, do not attempt jump-starting until it thaws.

1. Park the working vehicle near the disabled vehicle. Park the vehicle in such a way that the distance between both vehicle batteries is as small as practical. Turn off the engine, radio, lights, A/C, fans and all other electrical components. Make sure that all of these things are OFF in the disabled vehicle, too

   
   WARNING

   Don't let the vehicles touch each other.

2. Wear safety gear (goggles or face guard and gloves) if you have it.

   
   WARNING

   It may be necessary to remove the disabled vehicle’s battery cables from the battery terminals and clean both cables and terminals. Use a stiff wire brush to remove all corrosion. Reconnect the cables to the battery terminals and jump the vehicle.

3. Untangle and unwind your jumper cables. Like your batteries, your jumper cables will probably have red and black cables and will have heavy duty clamps to connect to the battery terminals. You must make sure that the red and black ends of your jumper cables never touch each other once they are connected to the batteries; permitting them to do so can result in serious arcing and/or damage to one or both vehicles

4. Connect the jumper cables in the order described below;

   • Connect one red clamp to the positive (+) terminal of the dead battery/disabled vehicle
   • Connect the other red clamp to the positive (+) terminal of the good battery
   • Connect one black clamp to the negative (-) terminal of the good battery
   • Connect the other black clamp to a piece of grounded metal on the dead vehicle, preferably shiny metal (not painted or oily) that is attached to the engine. Usually a nut, bolt or other protruding shiny metal will work. You may see a small spark when you connect to a good ground. As a last resort, you may connect to the negative (-) post of the dead battery, but this risks igniting hydrogen gas coming off the battery
   
   WARNING

   Make sure none of the cables are dangling into the engine compartment, where they could be exposed to moving parts.

5. Start the working vehicle. Let it idle for a few minutes. Rev the engine a little above idle for 30 to 60 seconds. You do this to charge the battery in the dead vehicle. A good clean connection between the battery cables and the battery terminals is essential
6. Try to start the disabled vehicle. If it does not start, shut the engine off and disconnect the last connection temporarily while you slightly twist or wiggle each of the four clamps to help ensure a good electrical connection. Restart the working vehicle again. Allow another 5 minutes for charging before attempting to start the disabled vehicle. If this does not work after a few tries, you may need to have the vehicle towed or the battery replaced
7. Remove the jumper cables once the vehicle starts. Do this in the reverse of the order in which they were attached, and don't let any of the cables or clamps touch each other (or dangle into the engine compartment)
   • Disconnect the black clamp from the grounded metal on the dead vehicle
   • Disconnect the black clamp from the negative (-) terminal of the good battery
   • Disconnect the red clamp from the positive (+) terminal of the good battery
   • Disconnect the red clamp from the positive (+) terminal of the dead battery

   Replace any positive (+) red post protective covers if applicable (You have had to remove or open these in the beginning) These covers help prevent accidental short circuiting of the battery

8. Keep the recently-disabled vehicle's engine running. Run the vehicle above idle (slightly revved up with your foot on the accelerator). This should give the battery enough charge to start the vehicle again. If it does not, you probably have a dead battery or a dying alternator
   WARNING

   Improper jump starting procedures can result in battery explosion and acid burn hazard. Loosely connected battery cables could damage the electronic control units. To disconnect battery terminals wait for at least 2 minutes to allow discharge of high voltage or it could lead to personal injury. While disconnecting, always disconnect the -VE terminal first and while connecting, always connect the -VE terminal last. Do not connect battery terminals with opposite polarity, it will lead to alternator failure

   WARNING

   Towing a vehicle to start could be dangerous. The vehicle being towed could surge forward when the engine starts, causing the tow vehicles to collide, injuring the occupants.

   Modern vehicles with electronic management systems should not be jump started without ‘protected’ jump starter leads. It is necessary to refer to the owner's handbook for jump starting procedures for such vehicles.

13.5 Towing

13.5.1 Towing Equipment

Towing equipment are of two types.

• Flat-bed equipment - Your vehicle is loaded on the back of a truck. This is the safest and best way of towing.
• Rear-lift equipment - The tow truck uses two pivoting arms that go under the tires (front or rear) and lift them off the ground. The other two tires remain on the ground.
• Sling-type equipment - The tow truck uses metal cables with hooks on both ends. These hooks go around parts of the frame or suspension and lift the end of the vehicle off the ground. This is not a good method of towing as it may damage the vehicle's suspension and body. Avoid a tow with sling type equipment

13.5.2 Towing your Vehicle During Emergency

If your vehicle needs to be towed, call a professional towing service. If a towing service is unavailable in an emergency, your vehicle may be temporarily towed by a cable or chain secured to the emergency towing hook screwed into the front towing eyelet. The tow eye is in the tool kit organiser above the spare wheel

For removal of the tow hook cap, press on the triangle mark over the cover using your thumb. Remove the cap, screw in the tow hook and tighten clockwise. Fasten a cable or chain specifically intended for use in towing vehicles to the towing hook.

13.6 Limp Home Mode

Limp home mode is an emergency situation declared by the EMS (Engine Management System) due to failure of one/more critical sensors/actuators. In this mode, the EMS (Engine Management System) will revert back to basic minimum requirement (fuel quantity / injection timings) to aid the driver to bring the vehicle back to the nearest workshop. Needless to say the drivability & fuel consumption will be greatly affected.

If vehicle acceleration worsens or if there is a drop in vehicle performance, there might be a malfunction in the engine management system which triggers/activates the Limp Home Mode. This condition is accompanied by the check engine lamp illuminating in the instrument cluster. In this mode, the vehicle speed is limited and the accelerator pedal may not function normally. It is recommended you contact an Authorized Mahindra Dealer immediately for assistance.

14.1 General Owners Information

Your vehicle has been designed for fewer maintenance requirements with longer service intervals to save both your time and money. However, each regular maintenance, as well as day-to-day care is more important to ensure a smooth, trouble free, safe and economical operation.

It is the owner's responsibility to make sure the specified maintenance, including general maintenance service is performed. Note that both the new vehicle limited warranty and emission control system limited warranties specify that proper maintenance and care must be performed. See Service Coupon Booklet for complete warranty information.

Mahindra technicians are well trained specialists and are kept up to date with the latest service information through technical bulletins, service tips and in dealership training programs. They learn to work on Mahindra vehicles before they work on your vehicle, rather than while they are working on it.

You can be confident that your Mahindra dealer's service department does the best job to meet the maintenance requirements on your vehicle reliably and economically.

Routine maintenance is the best way to help ensure you get the performance, dependability, long life and better resale value you expect from your vehicle. This is exactly why we've put together this Maintenance Section. It outlines the services required to properly maintain your vehicle and when they should be performed. The focus is on maintaining your vehicle while it's running great, which goes a long way toward preventing major repairs and expenses later.

Here are a few suggestions to help you get started on routine maintenance:

• Familiarize yourself with your vehicle by going through your Owner's Manual
• Take a few minutes to review this Maintenance Section
• Make it a habit to use this manual to record scheduled maintenance in the Service Coupon Booklet
• Consult with your Authorized Mahindra Dealer for all your vehicle's needs

14.1.1 Suggestions for Obtaining Service for your Vehicle

If you have warranty work to be done, be sure to have the right papers with you. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. Keep a maintenance log of your vehicle's service history.

Make a written list of your vehicle's problems or the specific work you want done. If you've had an accident or work done that is not on your maintenance log, let the service advisor know about it.

If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with the service advisor and list the items in order of priority.

14.1.2 Need Assistance?

It is recommended talking to an Authorized Mahindra Dealer service manager first. Most matters can be resolved with this process. If for some reason you are still not satisfied, talk to the general manager or owner of the dealership.

If an Authorized Mahindra Dealership is unable to resolve the concern, you may contact any Mahindra Customer Care executive. They would need the following information:

Owner's name and address, owner's telephone number (home and office), Authorized Dealership name, Vehicle Identification Number (VIN), vehicle delivery date and mileage.

14.1.3 Warranty Information

Read the Warranty Information given in the ‘Warranty Information & Maintenance Guide’ for the terms and provisions of Mahindra warranties applicable to this vehicle. Mahindra genuine parts, fluids, lubricants and accessories are available at any Authorized Mahindra Dealer. They will help keep the vehicle operating at its best.

14.1.4 Protect your Warranty

Routine maintenance is not only the best way to help keep your vehicle performing as intended, it's also the best way to protect your warranty. Failure to perform scheduled maintenance specified in the Service Coupon Booklet will invalidate warranty coverage on parts affected by the lack of maintenance. We can't stress enough how important it is to keep records of all maintenance. Damage or failures due to neglect or lack of proper maintenance are not covered under warranty.

Keeping maintenance records is easy with the service coupon booklet

It's important to document the maintenance of your vehicle. For your convenience to maintain records of service, the scheduled maintenance coupons are provided in the service coupon booklet. Every time you bring your vehicle in for scheduled maintenance, be sure to present this booklet and certify the work. Also record the date of service and mileage at the time of service. This will make record keeping easy and, should your vehicle ever require warranty coverage, you will have all the documentation to show you've properly maintained it.

14.1.5 Maintenance Interval

Mahindra establishes recommended maintenance intervals based upon engineering testing to determine the most appropriate mileage to perform the various maintenance services. This protects your vehicle at the lowest overall cost to you. Mahindra recommends that you do not deviate from the maintenance schedules presented in this Maintenance Schedule.

14.1.5.1 Oils, Fluids and Flushing

In many cases, fluid discoloration is a normal operating characteristic by itself, and does not necessarily indicate a concern or that the fluid needs to be changed. However, discolored fluids that also show signs of overheating and/or foreign material contamination should be inspected immediately by a qualified expert such as the factory trained technicians at your Authorized Mahindra Dealer. Your vehicle's oils and fluids should be changed at the specified intervals or in conjunction with a repair.

14.1.5.2 Chemicals and Additives

Non-Mahindra approved chemicals or additives are not required for factory recommended maintenance. In fact, Mahindra recommends against the use of such additive products unless specifically recommended by Mahindra for a particular application.

Your vehicle is very sophisticated and built with multiple complex performance systems. Every manufacturer develops these systems using different specifications and performance features. That's why it's important to rely on your Authorized Mahindra Dealer to properly diagnose and repair your vehicle.

When planning your maintenance services, consider your Authorized Mahindra Dealer for all your vehicle's needs.

14.1.5.3 Get the most from your service and maintenance visits

Getting your vehicle serviced at an Authorized Mahindra Dealer adds great value to your vehicle in number of ways. Hence, it is recommended to service your vehicle at an Authorized Mahindra Dealer only.

14.1.6 Vehicle Self Maintenance - General Precautions

• Refer to relevant sections of the manual before starting
• Set the parking brake
• Block the wheels to prevent the vehicle from moving unexpectedly
• Turn OFF the engine and remove the key
• Stay clear of hot vehicle parts
• Avoid repeated contact with fluids
• Do not let fuel, coolant and other fluids spill over electrical and hot vehicle parts
• Keep all open flames and other burning material like cigarettes away from the battery and all fuel related parts

14.2 Opening/Closing the Hood

The hood release lever is located in the driver side foot well area, below the instrument panel. To open the hood, follow the steps below;

1. Pull the lever to release the hood

   

2. Lift the hood a little to access the safety latch holding the hood striker. This safety latch is located below the hood at the center

   

3. Move the safety latch to the left and lift the hood up

4. Remove the stay rod from the hood lock

   

5. Support the hood by the stay rod in the slot provided

   

Follow the below steps to close the hood;

1. Pull the hood down to a few inches above its fully closed position
2. Now, release the hood and allow it to fall by its own weight. The secondary latch is engaged now.
3. Firmly press the hood down with both your hands to engage the primary latch. This ensures that safety latch firmly locks the hood in its fully closed position

14.3 Identifying Components in the Engine Compartment

Maintenance is classified as below;

• General Maintenance
• Scheduled Maintenance

14.4 General Maintenance

Listed below are the general maintenance items that should be performed frequently. In addition to checking the items listed below, if you notice any unusual noise, fluid leakages, smell or vibration, you should investigate the cause or take your vehicle to your Authorized Mahindra Dealer or a qualified service shop immediately.

• Front windshield washer fluid level
• Engine coolant level
• Battery condition
• Brake/Clutch fluid level
• Engine oil level
• Fluid leaks
• Hoses, joints and pipes for any abnormalities

• Lights
• Warning lamps
• Windshield wipe and wash
• Steering wheel
• Seats
• Seat belts
• Accelerator pedal
• Brake pedal
• Brakes
• Parking brake
• Gear lever shift mechanism

• Lamps
• Fluid leaks
• Doors and engine hood latches
• Tire inflation pressure
• Tire surface/thread and wheel bolts

14.5 In the Engine Compartment

14.5.1 Fluid Leaks

Check the engine compartment and the underbody of the vehicle for any leaks. If you smell fuel vapor or notice any leak, have the cause found and corrected immediately.

14.5.2 Engine Oil

Engine oil has the primary function of lubricating and cooling the inside of the engine. It plays a major role in maintaining the engine in proper working order. Therefore, it is essential to check the engine oil regularly.

14.5.3 Engine Oil Consumption

It is normal for engines to consume some engine oil during operation.

Causes of consumption in a normal engine are as follows;

• Oil is used to lubricate pistons, piston rings and cylinders. Thin films of oil, left over when pistons move in cylinders, are sucked into the combustion chamber due to high negative pressure generated when the vehicle is decelerating. This oil gets burnt in the combustion chamber
• Oil is also used to lubricate the stems of intake valves. Some of this oil is sucked into the combustion chamber together with the intake air and is burnt there
• Engine oil consumption depends upon the viscosity and quality of the oil, and upon the conditions in which the vehicle is driven. Oil consumption will be more due to high speed driving and frequent acceleration and deceleration. A new engine may consume more oil since its pistons, piston rings and cylinder walls are not conditioned

14.5.4 Checking/Topping the Engine Oil

• Make sure the vehicle is on level ground
• Turn the engine OFF and wait a few minutes for the oil to settle down into the oil sump
• Apply the parking brake
• Open the hood. Protect yourself from engine heat
• Locate and carefully remove the engine oil level dipstick
• Petrol
• Diesel
• Wipe the dipstick with a clean cloth. Insert the dipstick fully, then remove it again
• If the oil level is between “Two Dot marks”, the oil level is acceptable. DO NOT ADD OIL
• If the oil level is below the ‘Lower Dot mark’, add enough oil through the oil filler neck to raise the level within the Two Dot marks. Wait for a few minutes after every top up for the oil to settle down before checking the level.
• Petrol
• Diesel
• Oil levels above the ‘Upper Dot’ mark may cause engine damage/poor performance.
• Put the dipstick and the oil filler cap back and ensure it is fully/properly seated.

14.5.5 Checking/Topping Engine Coolant Level

• Park the vehicle on a flat-horizontal surface. Keep the parking brake fully engaged. Shut-off the engine
• Wait till the engine cools down and hence coolant temperature comes down to normal room temperature
• The coolant level should be between ‘MIN’ and ‘MAX’ marking provided on the coolant recovery tank
• In case the coolant level is below the ‘MIN’ marking, the coolant should be topped-up
• The coolant should be filled till the level rises above the ‘MIN’ but remain below the ‘MAX’ marking on the coolant recovery tank
• However if the Coolant Recovery Tank is found to be near empty, it is recommended that the system be checked at an Authorized Mahindra Dealer

14.5.6 Checking/Topping Brake/Clutch Fluid

The brake system is supplied with brake fluid from the brake fluid reservoir located adjacent to the air filter.

The brake fluid level will drop slowly as the brakes wear, and will rise when the brake components are replaced. Fluid levels between the ‘MIN’ and ‘MAX’ lines are within the normal operating range; there is no need to add fluid. If the fluid levels are below the ‘MIN’ mark, the performance of the systems could be compromised; the brake/clutch operation could be spongy and gear change harder.

Top-up the recommended brake/clutch fluid till the ‘MAX’ mark or contact an Authorized Mahindra Dealer immediately.

Carefully clean the cap on the reservoir before you remove it and be sure no debris fall in the reservoir. Do not keep the reservoir open for longer than necessary to add brake fluid.

Use only brake/clutch fluid that meets Mahindra specifications. Refer to the ‘Lubricant and Capacities’ section.

14.5.7 Windshield Washer Fluid Top-up

Top up the windshield washer reservoir as and when required. The fluid reservoir is located on the RHS of the engine bay behind the head lamp. The reservoir supplies washer fluid to both front and rear (if equipped).

In very cold weather conditions, fill the reservoir with washer fluid premixed with anti-freeze.

14.5.8 Checking the Wiper Blades

Lift the wiper arm from its position. Expose the blade lip for inspection. Clean the wiper blade lips with water applied with a soft sponge. If the wiper blade is not wiping the glass satisfactorily or is worn-out, cut, cracked or bulging get it replaced at an Authorized Mahindra Dealer.

14.5.9 Changing the Wiper Blade

1. Lift the arm and position the wiper blade at right angles to the wiper arm
2. Press the retaining clip in the opposite direction, disengage the wiper blade and pull it off the arm To prevent damage to the windshield, don’t let the wiper arm slap down on to it.
3. Hold the end of the rubber and pull until the tabs are free of the metal support
4. Carefully insert the new blade rubber. Then install the blade assembly in the reverse order of removal

14.6 Maintenance - Inside the Vehicle

14.6.1 Lights

Make sure the headlights, stop lights, tail lights, turn signal lights and other lights are all working. Check headlight aim.

14.6.2 Warning Messages and Lamps

Check all warning lamps appearing in the instrument cluster. Refer to the relevant sections in this manual for further details.

14.6.3 Seats

Check that all seat controls such as seat adjusters, seat back recliner, etc. operate smoothly and that all latches lock securely in any position. Check that the head restraints move up and down smoothly and that the locks hold securely in any latched position.

14.6.4 Seat Belts

Check that the seat belt system such as buckles, retractors and anchors operate properly and smoothly. Make sure the belt webbing is not cut, frayed, worn or damaged.

14.6.5 Accelerator Pedal

Check the pedal for smooth operation, uneven pedal effort or stickiness. Check the foot well and remove obstructions if any.

14.6.6 Brake Pedal

Check the pedal for smooth operation and proper clearance. Check the foot well and remove obstructions if any.

14.7 Maintenance - Outside the Vehicle

The following checks should be carried out from time to time, unless otherwise specified.

14.7.1 Lamps

Check and ensure proper functioning of all exterior lamps.

14.7.2 Fluid Leaks

Check the engine compartment and the underbody of the vehicle for any leaks. If you smell fuel vapor or notice any leak, have the cause found and corrected immediately.

14.7.3 Doors and Engine Hood

Check all doors and latches including the tailgate for proper functioning. Make sure the engine hood secondary latch secures the hood from opening when the primary latch is released.

14.7.4 Tyre Inflation Pressure

Check the tire pressure with a pressure gauge every week.

14.8 Battery

Your vehicle is equipped with a Mahindra genuine battery. For longer, trouble-free operation, keep the top of the battery clean and dry. Also, make certain the battery cables are always tightly fastened to the battery terminals.

If you see any corrosion on the battery or terminals, remove the cables from the terminals and clean with a wire brush. To prevent corrosion, apply petroleum jelly to the battery terminals. Tighten loose terminals and hold down clamp nuts only enough to keep the battery firmly in place. Tightening excessively may damage the battery terminals.

14.8.1 For Best Battery Service

• Keep the battery securely mounted
• Keep the battery top clean and dry
• Keep the terminals and connections clean, tight and coated with petroleum jelly or terminal grease
• Rinse any spilled electrolyte from the battery immediately with a solution of water and baking soda

It is recommended that the negative battery cable terminal be disconnected from the battery if you plan to store your vehicle for an extended period of time. This will minimize the discharge of your battery during storage.

14.8.2 Battery Charge Indicator - Amaron (if equipped)

A battery charge indicator is provided for Amaron batteries to view the charge status at a glance. Green indicates the battery is okay, and light blue indicates battery needs recharge or technical assistance from Amaron.

14.8.3 Battery Charge Indicator - Exide (if equipped)

A battery charge indicator is provided for Exide batteries to view the charge status at a glance.

Three charge indicators are provided which give the following information;

• GREEN — OK (Battery condition good)
• WHITE— Needs charging
• RED— Add distilled water

14.8.4 Checking the Electrolyte Level

Check the electrolyte level and specific gravity at intervals of three months. Check all the six cells for proper electrolyte levels. If the level is below the lower marker, add distilled water until the level reaches the upper marker.

Adding distilled water;

• Remove the vent plugs
• Add distilled water to all the cells that require the fluid and secure the plugs properly

14.9 Appearance Care and Protection

14.9.1 Washing the Exterior

• Wash your vehicle regularly with cool or lukewarm water and a neutral pH soap
• Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces
• Never wash a vehicle that is ‘hot to the touch’ or during exposure to strong, direct sunlight
• Always use a clean sponge or car wash mitt with plenty of water for best results
• Dry the vehicle with a chamois or soft terry cloth towel in order to eliminate water spotting
• It is especially important to wash the vehicle regularly during the winter months, as dirt and road salt are difficult to remove and cause damage to the vehicle
• Immediately remove items such as petrol, diesel fuel, bird droppings and insect deposits; they can cause damage to the vehicle's paint work and trim over time

14.9.2 Engine Compartment

14.9.3 Exterior Chrome

• Wash the vehicle first, using cool or lukewarm water and a neutral pH shampoo
• Use the custom bright metal cleaners, available at your Authorized Mahindra Dealer. Apply the product as you would wax to clean chrome parts; allow the cleaner to dry for a few minutes, and then wipe off the haze with a clean, dry rag
• Never use abrasive materials such as steel wool or plastic pads as they can leave scratches on the chrome surface
• After polishing the chrome parts, you can also apply a coating of Premium Liquid Wax, available at your Authorized Mahindra Dealer, or an equivalent quality product to help protect from environmental effects

14.9.4 Paint Chips

• Mahindra dealers have the exact touch-up paint to match your vehicle's color
• Take your vehicle to an Authorized Mahindra Dealer for paint touch-up or paint repairs
• Remove particles such as bird droppings, tree sap, insect deposits, tar spots, road salt and industrial fallout before repairing paint chips
• Always read the instructions before using the products

14.9.5 Aluminium Wheels And Wheel Covers (if equipped)

Aluminum wheels and wheel covers are coated with a clear coat of paint finish. In order to maintain their shine;

• Clean weekly with wheel and tire cleaner, which is available at your Authorized Mahindra Dealer. Heavy dirt and brake dust accumulation may require agitation with a sponge. Rinse thoroughly with a strong stream of water
• Never apply any cleaning chemicals to hot or warm wheel rims or covers
• Do not use hydrofluoric acid-based or high caustic-based wheel cleaners, steel wool, fuels or strong household detergents

14.9.6 Plastic (Non-painted) Exterior Parts

Use only approved products to clean plastic parts. These products are available with your authorized dealer. You can use these cleaners;

• For routine cleaning of plastic parts
• For tar or grease spots
• For plastic head lamp lenses

14.9.7 Windows and Wiper Blades

The front/rear windshield, side windows and the wiper blades should be cleaned regularly. If the wipers do not wipe properly, substances on the vehicle's glass or the wiper blades may be the cause. These may include hot wax treatments used by commercial car washes, water repellent coatings, tree sap, or other organic contamination; these contaminants may cause squeaking or chatter noise from the blades, and streaking and smearing of the windshield.

To clean these items follow these tips;

• The windshield, rear windows and side windows may be cleaned with a non-abrasive cleaner such as Clear Spray Glass Cleaner, available at your Authorized Mahindra Dealer.
• The wiper blades can be cleaned with alcohol or Premium Windshield Washer Concentrate, available at your Authorized Mahindra Dealer. This washer fluid contains a special solution in addition to alcohol which helps remove the hot wax deposited on the wiper blade and windshield. Be sure to replace wiper blades when they appear worn or do not function properly.
• Do not use abrasives, as they may cause scratches.
• Do not use fuel, kerosene, or paint thinner to clean any glass parts.

If you cannot remove those streaks after cleaning with the glass cleaner or if the wipers chatter and move in a jerky motion, clean the outer surface of the windshield and the wiper blades using a sponge or soft cloth with a neutral detergent or mild-abrasive cleaning solution. After cleaning, rinse the windshield and wiper blades with clean water. The windshield is clean if beads do not form when you rinse the windshield with water.

Do not use sharp objects, such as a razor blade, to remove decals, as it may cause damage to the glass or rear windshield heater grid lines (if equipped).

14.9.8 Instrument Panel/Interior Trim and Cluster Lens

Clean the instrument panel, interior trim areas and cluster lens with a clean and damp white cotton cloth, then with a clean and dry white cotton cloth; you may also use Dash and Vinyl Cleaner on the instrument panel and interior trim areas.

• Avoid cleaners or polishes that increase the gloss of the upper portion of the instrument panel. The dull finish in this area helps protect the driver from undesirable windshield reflection
• Do not use household or glass cleaners as these may damage the finish of the instrument panel, interior trim and cluster lens

If a staining liquid like coffee/juice has been spilled on the instrument panel or on the interior trim surfaces, clean as follows;

• Wipe up spilled liquid using a clean white cotton cloth
• Apply Vinyl Cleaner to the wiped area and spread around evenly
• Apply cleaner to a clean white cotton cloth and press the cloth onto the soiled area and allow this to set in at room temperature for 30 minutes
• Remove the soaked cloth, and if it is not soiled badly, use this cloth to clean the area with a rubbing motion for 60 seconds
• Following this, wipe area dry with a clean white cotton cloth

14.9.9 Interior Maintenance

For fabric, carpets, cloth seats, safety belts and seats:

• Remove dust and loose dirt with a vacuum cleaner
• Remove light stains and soil with carpet and upholstery cleaner
• If grease or tar is present on the material, spot-clean the area first with a stain remover
• Do not use household cleaning products or glass cleaners, which can stain and discolor the fabric and affect the flame retardant abilities of the seat materials
• Do not use cleaning solvents, bleach or dye on the vehicle's safety belts, as these actions may weaken the belt webbing.

14.9.10 Underbody

Flush the complete underside of your vehicle frequently. Keep body and door drain holes free from packed dirt. You can also use an anti-corrosion spray for the underbody to avoid rusting and corrosion especially for vehicles in coastal places.

14.10 Air Conditioning System Maintenance

Your vehicle's air-conditioning is a sealed system. Any major maintenance, such as recharging should be done by a qualified technician. However, you can do a few things by yourself to make sure the air conditioning works efficiently.

Run the air-conditioning system at least once a week, even during the cold weather months. Run it for at least ten minutes with the engine running at normal operating temperature. This circulates the lubricating oil contained in the refrigerant.

14.11 Vehicle Storage

If you are leaving your vehicle for more than 2 weeks you may want to take stopping to protect your battery. Disconnect the negative cable from the battery. Anytime you store your vehicle, or keep it out of service (i.e. vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air mode and high blower speed setting. This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again.

It is recommended storing the vehicle in a covered, clean, dry, well leveled, ventilated and closed place.

14.12 Winter Care

14.12.1 Dealing With Ice

Make sure you have window ice scrapers and de-icers for the locks. When you're stuck, having a small shovel is useful to dig out of the snow. The weight of a bag of sand in the trunk will give added traction in rear-wheel drive vehicles and can be used to sprinkle on the snow and ice to gain better traction. And don't forget personal protection such as a warm coat, hat, gloves and a blanket, in case you get stuck in a storm.

14.12.2 Keep Enough Fuel in the Tank

Never let the fuel level in the tank drop below the half-full mark. A sudden storm with unexpected heavy rains could leave you stranded for hours. Having adequate fuel supply will allow you to idle the engine from time to time to keep warm.

Do not:

• Tap the ice on the window to crack it or chip it for a good place to start scraping. You could end up cracking more than the ice and end up with a cracked or shattered windshield/ window
• Pour warm or hot water on the windshield to melt ice. This will crack your windshield

14.12.3 During Winter Storage

Start the engine occasionally, here are a few pointers to keep in mind;

• Run it in a well ventilated area. Carbon monoxide can build up quickly
• Run for a minimum of 20 minutes to allow the engine to come up to the normal operating temperature. This will allow the oil to circulate and will also open up the thermostat so that your radiator anti-freeze circulates as well
• Start up the air conditioner and/or heater and run both for 10 minutes or so. Again, circulating fluids is essential for good life of the system
• If your vehicle has power steering, you may want to turn the wheels a few times to keep the fluids flowing

14.12.4 Exterior

Wash and wax your car to provide an extra layer of protection to your paint.

14.12.5 Vinyl and Rubber

Use a good conditioner on all vinyl and rubber parts to prevent from drying out.

14.12.6 Interior

Clean the glass, shampoo the carpets, dig in between the seats to see what's there, clean the upholstery in all nooks and corners.

14.12.7 Engine

Check all hoses and wires to make sure everything is in good condition and replace any that need to be. The last thing to do is to make sure the internal components of the engine remain lubricated and don't corrode.

14.13 Bulb Replacement

14.13.1 Head Lamp Bulb Replacement

To replace the head lamp bulb;

• Ensure ignition is switched OFF
• Disconnect the head lamp connector from bulb
• Remove rear dust cover from the head lamp
• Detach the bulb assembly from the head lamp by unlocking the wire clamp
• Insert the new bulb (of the same wattage), and follow the reverse procedure to assemble the bulb assembly in the headlight assembly
• Clamp the bulb assembly by wire clamp properly

14.14 Scheduled Maintenance

The scheduled maintenance jobs listed in the ‘Scheduled Maintenance Chart’ are those required to be carried out at regular predetermined intervals.

To make sure that your vehicle runs efficiently all the time, follow the maintenance schedule. The service interval for the scheduled maintenance is determined by the odometer reading. Take your vehicle to an Authorized Mahindra Service Station only. Trained technicians and genuine Mahindra parts at Mahindra Authorized service stations are best for your vehicle. They will perform all the scheduled maintenance jobs reliably and economically. Inadequate, incomplete and insufficient servicing may result in problems.

The owner should retain records/documents that proper maintenance has been performed as prescribed.