1.1 Introduction

Dear Customer,
Congratulations on purchasing Mahindra XUV500. Your vehicle has been designed to provide years of safe and dependable service, as long as it is used and maintained in accordance with the instructions provided in this manual.

All persons who will use and/or maintain this vehicle must read, understand and follow all warnings and instructions provided in this manual. This Owner's Manual should be considered an integral part of the vehicle and should remain with the vehicle. However, nothing in this manual, and none of the safety devices installed in the vehicle, are a substitute for careful operation and common sense. Always make sure that your vehicle is in optimum working order, and take note of the road and weather conditions under which you are using your vehicle.

If you have any questions concerning the proper use or maintenance of your vehicle, please call your Authorized Mahindra Dealer. A list of dealers can be found in the Dealer Directory Supplement.

Alternatively you can contact Mahindra at,

• 1800-209-6006 (Toll free)
• customercare@mahindra.com

We extend our best wishes for safe and pleasurable motoring. Sincerely,
MAHINDRA & MAHINDRA LTD.

Servicing and Summary Data

• For all issues concerning the vehicle and for any need for spare parts, contact only the Authorized Mahindra network
• We recommend you always use genuine Mahindra spare parts when performing repairs on the vehicle
• We suggest that you record the vehicle data in the Service Coupon Booklet for future references

1.2 Safety Symbols

Carefully read, understand and follow the safety symbols/ instructions given in this manual.

To emphasize information and procedures regarding safety, use, maintenance, etc., the following symbols are used throughout the manual.

1.3 General Safety Information and Instructions

Failure to follow the warnings and instructions provided in this manual could result in failure of the vehicle, an accident and/or serious personal injury.

1. Carefully read, understand and follow the warnings and instructions given in this manual. This manual is an essential part of the product. Keep it in the vehicle glove box for future reference
2. Spare bulb and first aid kit are placed in the glove box of the vehicle. Ensure they are not taken out of the vehicle at any point of time.
3. Please note that throughout this manual, reference is made that “an accident” could occur. An accident could cause you or a bystander to sustain severe personal injury, or result in property damage
4. Never use a mobile phone or personal music device while driving. This may take your focus off the road and lead to accidents
5. Please be advised that many service and repair tasks require specialized knowledge, tools and experience. General mechanical aptitude may not be sufficient to properly service or repair your vehicle. If you have any doubt whatsoever regarding your ability to properly service or repair your vehicle, please contact your Authorized Mahindra Dealer or a qualified technician
6. Inspect the seat belt system periodically, checking for cuts, frays or wear in the seat belt webbing, or loose buckles, retractors, anchors or other loose parts. Damaged parts must be replaced immediately
7. Always start and operate the engine in a well-ventilated area. If in an enclosed area, vent the exhaust to the outside. Do not modify or tamper with the exhaust system
8. Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread and check sidewalls for any cuts, cracks, or other signs of wear. Replace as necessary
9. Always maintain the safety labels affixed to your vehicle in a good legible condition
10. All signal lamps, buzzers, shields, guards and other protective safety devices must always remain in place and in good, proper working condition
11. The life span of Mahindra products depend on many factors. Improper use, abuse or harsh use in general may compromise the integrity of the vehicle and significantly reduce its life span. The vehicle is also subject to wear over a period of time. Please have your vehicle regularly inspected by an Authorized Mahindra Dealer or a qualified mechanic. If the inspection reveals any damage or excessive wear, immediately replace or have the component serviced
12. We recommend that you use only genuine parts supplied by Mahindra. The use of non-Mahindra parts will not be covered by warranty
13. Never crawl under or be in close proximity to the vehicle when it is lifted off the ground (by a jack), unless the vehicle is properly supported with jack stands, wheel chocks and other appropriate safety devices
14. Never attempt any repairs or adjustments to any component while the vehicle is in motion. Always switch off the engine, and wait for the engine to come to a complete stop before performing any repairs or adjustments
15. The vehicle identification plates are the only legal identification reference, hence it is necessary to keep them in good condition. Never modify data on the plates or remove them. The customer is responsible for any possible tampering with the plates, which will immediately void the warranty
16. Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control. When the vehicle is fully loaded, drive at a slow speed, especially when turning. Note that the center of gravity of the vehicle increases as the vehicle is fully loaded on the roof carrier

1.4 To Owner’s of a Mahindra Vehicle

When first driving the vehicle after long periods of non-use, you may experience a temporary drive disturbance. This is a characteristic of the tires and should be no reason for concern. The condition should correct itself within 5-15 kms. of driving. If the disturbance persists, have the tires checked by an Authorized Mahindra Dealer.

Your driving ability can be seriously impaired by alcohol even if the blood alcohol level is far below the legal minimum. Drunken driving is one of the most frequent causes of accidents.

Never drink and drive. Drinking and driving will lead to an accident resulting in serious personal injury.

Your driving ability can be seriously impaired through the use of prescription or non-prescription drugs or medication (even cough syrup). If you are taking any sort of drug or medication, be sure that it will not affect your driving ability.

Use of electrical devices such as mobile phones, computers, portable radios or other by the driver while driving is dangerous. If use of a mobile phone is necessary despite this warning, use a hands free system to at least leave the hands free to drive the vehicle.

Please comply with the legal regulations concerning the use of communication equipment in vehicles in your country.

When you are driving over long distances, follow these tips so that you have a safe journey;

• Lack of sleep or fatigue may impact your ability to drive safely.
• Exercise your eyes by shifting the focus of your eyes to different parts of the road.
• Use stimulating beverages such as coffee or tea.
• Relax and stay calm.

Every one of us should play our part in protecting our environment. Judicious vehicle usage and disposing hazardous waste (including cleaning and lubrication fluids) are important steps towards this initiative.

Mahindra vehicles confirm to existing emission norms (standards). Adhering to the periodical maintenance schedule and using Mahindra genuine parts will help retain emission performance of the vehicle and is a pre-requisite to emissions warranty coverage.

If you have any questions concerning the proper use or maintenance of your vehicle, please call your Authorized Mahindra Dealer. A list of dealers can be found in the Dealer Directory Supplement or on the Internet.

Alternatively you can contact Mahindra on 1800-209-6006 / customercare@mahindra.com.

Driving smoothly during first 1000 kms. will help to prevent premature failures and abnormal system wear improving the life of drivetrain and vehicle components.

A new engine may consume more oil during the first 1000 kms. of running. This should be considered as a normal part of break-in and not interpreted as any problem with the engine.

To ensure optimum vehicle performance and passenger safety, your Mahindra vehicle is equipped with sophisticated modern electronics and controls. Do not install any communication devices, electronic gadgets or radar detection devices, without express written consent from Mahindra.

An improperly installed/adjusted two-way radio can adversely affect electronic systems.

Mahindra uses high quality parts for building vehicles.

In the event that any parts need replacement, we recommend that you use only Mahindra genuine parts.

Non-Mahindra parts may harm vehicle performance and will not be covered by your Mahindra warranty.

To avoid counterfeit parts and to protect our brand image, Mahindra genuine parts are packed in a branded carton. Look for the “Mahindra Genuine Parts” logo.

Any unauthorized modifications or alterations to this vehicle or failure to use appropriate specification and quality spare parts could seriously affect vehicle road worthiness and safety leading to an accident, resulting in serious injury.

A wide selection of quality accessories is available through your authorized Mahindra dealership. These accessories have been specifically engineered to allow you to personalize your vehicle to suit your requirements and compliment its style and aerodynamic appearance.

Each accessory is made from high quality materials and meets Mahindra's rigid engineering and safety specifications. Every Mahindra accessory installed according to the Mahindra installation provisions comes with the respective accessory warranty.

Consult your Mahindra authorized dealer for detailed information about accessories available for your specific model variant.

1. When adding accessories, equipment, passengers and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front and rear axle. Consult Mahindra authorized dealer for specific weight information.
2. Bull bars and nudge guards are not recommended for variants with an airbag.
3. Accessories causing any change in vehicle specifications like wheel rims, bull bars, etc., may affect the performance of safety systems.
4. Mobile communication systems such as two way radios, telephones and theft alarms that are equipped with radio transmitters and installed in your vehicle should comply with the local regulations and should be installed only by a your Authorized Mahindra Dealer

When leaving your vehicle unoccupied;

1. Always remove the ignition key when you park the vehicle
2. Close all the windows completely and lock all the doors
3. Do not leave any valuables in your vehicle. If you must leave something in your vehicle, hide them and securely lock all the doors

Please refer the Audio/Infotainment manual available in the manual pouch for details regarding;

• Audio/Video functions
• Bluetooth functions
• Navigation (if equipped)
• Map upgradation details

To upgrade the maps in your navigation system (if equipped), please refer the Infotainment manual.

2.1 Feature Matrix

In view of the policy of continuously improving our products, we reserve the right to alter specifications or designs without prior notice and without liability/obligation. Illustrations do not show the vehicle in the standard form. Please be aware that this manual may apply to various models/variants . As a result you may find some explanations for equipment not installed on your vehicle. All the information, illustration, and specifications in this manual are based on the latest product information available at the time of publication.

We recommend you to contact the nearest Mahindra dealer for latest features applicable to your vehicle.

2.2 Dimensions

2.2.1 Front View

2.2.2 Rear View

2.2.3 Side View

2.3 Lubricants and Capacities

2.4 Bulb Specification

2.5 Fuses & Relays

A fuse is the most common electric protection device. A fuse is placed in an electrical circuit, so that when current flow exceeds the rating of the fuse it blows off.

The element in the fuse melts, opening the circuit and preventing other components of the circuit from being damaged by the over current. The size of the metal fuse element determines the rating. Once a fuse blows off, it must be replaced with a new one.

Switch the ignition and all electrical equipment OFF before touching or attempting to change a fuse.

Fit replacement fuse with the same rating as the one you have removed.

You can identify a blown fuse by a break in the filament. All fuses except high current fuses are a push fit. A fuse puller should be used to remove the fuse from its position.

2.5.1 Engine Compartment Fuse Box

Engine compartment fuse box is located adjacent to vehicle battery. Release the lock to access the fuse box contents. Remove the fuse box cover by pressing the clips from both sides using both hands simultaneously. Spare fuses are provided in the fuse box for replacement of blown fuses. Ensure the correct rating fuse is replaced with the blown fuse.

2.5.2 Instrument Panel Fuse Box

Fully open the driver door and slide the driver seat backwards. The main central fuse box is located on the right side of the instrument panel. Price out the securing cover to access the fuse box.

2.5.3 Floor Fuse Box (W10 variant only)

The floor fuse box is located under the LH A-Pillar lower trim.

2.6 Flat Tire

In case of a flat tyre during driving, reduce your speed gradually, keeping a straight line. Move cautiously off the road to a safe place well away from traffic. Park on a level spot with firm ground. Stop the engine and turn ON your hazard warning flashers.

Firmly apply the parking brake. Have everyone come out of the vehicle on the side away from traffic.

Never stop your vehicle in a traffic lane to change a tire. You could be hit by an oncoming vehicle. Keep driving until you reach a safe location.

Lifting a vehicle to change a tyre or perform maintenance is very dangerous if you do not have the requisite tools, safety equipment and training. The jack provided along with the vehicle is to be used only for changing a spare tire. It is never to be used to perform any other maintenance or repair on the vehicle.

Never place any part of your body under any portion of the vehicle when it is supported only by the jack. You could be crushed by the vehicle if it falls off a jack. Keep by-standers away from the vehicle.

Find level, solid ground that is clear of oncoming traffic. If you cannot find a safe place to stop, it is better to drive on a flat tyre and damage the rim than it is to risk being hit by oncoming traffic.

After changing a flat tire, never store the tyre or other equipment in the passenger compartment of the vehicle. This loose equipment could strike an occupant in the event of a sudden stop or collision. Store all of these items in the proper place.

2.6.1 Tool Kit

The tool kit is located behind the third row seats on the floor.

The tool kit consists of the following tools packed in a PVC tool bag;

• Assembly Screw Jack
• Jack Operating Lever
• Wheel Spanner
• Tow Bar
• DEO Spanner 10mm x 12mm
• Screw Driver

The warning triangle is located on the rear door trim below the camping lamp. Rotate the two securing knobs and lower the hinged cover. Un-strap the two holding belts and remove the warning triangle pouch.

2.6.2 Spare Wheel Removal

Spare wheel is located below the floor at the rear end of the vehicle. It is held in place by a securing nut underneath the rear luggage compartment floor carpet.

• Locate the plug covering the securing nut below the rear luggage compartment floor carpet. Remove the plug using a coin.

• Loosen the securing nut counter clockwise to winch down/lower the secured spare wheel to the ground.
• Rotate the securing bracket counter clockwise and remove it out of the spare wheel hub
Remove/pull away the spare wheel

To remove the wheel cover, wrap the tip of a screw driver with cloth, insert it near the lugs of the wheel cover and pry the cover away from the wheel.

Do not try to pry off the wheel cover by hand alone. Take due care in handling the wheel cover to avoid unexpected personal injury.

2.6.3 Wheel Nut Loosening

Always loosen the wheel nuts before raising the vehicle. Turn the wheel nuts counter clockwise to loosen. To get maximum leverage, fit the spanner to the nut so that the handle is on the right side. Grab the spanner near the end of the handle and push down on the handle. Be careful that the spanner does not slip off the nut. Do not remove the nuts, but loosen them by one or two turns.

Do not apply force with your legs (or stand) on the wheel spanner while tightening the wheel nuts.

Block the wheel diagonally opposite the flat tyre to keep the vehicle from rolling when it is jacked up. When blocking the wheel, place a wheel block in front of one of the front wheels or behind one of the rear wheels.

2.6.4 Jacking

Locate the jack points in the front or rear as needed. They can be identified by a slot used to fit the jack precisely.

Position the jack at the correct jacking point. Make sure the jack is positioned on a level and solid place.

To raise the vehicle, insert the jack handle end with the jack operating lever, wheel spanner square slot into the jack operating lever and turn it clockwise with the handle. As the jack touches the vehicle and begins to lift, check that it is properly positioned.

Ensure no one is in the vehicle. Raise it high enough so that the spare tyre can be installed. Remember you will need more ground clearance when putting on the spare tyre than when removing the flat tire.

Make sure to set the jack properly in the jacking point. Raising the vehicle with jack improperly positioned will damage the underbody of vehicle or may allow the vehicle to fall off the jack and cause personal injury.

• Use the jack only for lifting your vehicle during wheel changing
• When raising the vehicle, do not place any objects on top of or underneath the jack.
• Do not raise the jack with someone in the vehicle.
• Raise the vehicle only high enough to remove and change the wheel.
• Follow jacking instructions
• Do not start or run the engine while your vehicle is supported by the jack.

Never get under the vehicle when the vehicle is supported by the jack alone.

Remove the wheel nuts. Lift the flat tyre straight off and place it aside. Roll the spare wheel into position and align the holes in the wheel with the bolts. Lift up the wheel and get at least the top bolt started through its hole. Wiggle the wheel and press it back over the other bolts.

Before putting on the wheels, remove any corrosion on the mounting surfaces with a wire brush or such. Installation of wheels without good metal to metal contact at the mounting surface can cause wheel nuts to loosen and eventually cause a wheel to come off while driving.

Reinstall the wheel nuts with the tapered end inward and tighten by hand. Press the wheel inward and tighten the wheel nuts further.

Never use oil or grease on the bolts or nuts. Doing so spanner slip, damage the bolts and also may cause personal injuries. Also, nuts may loosen and the wheels may fall off, which could cause a serious accident. If there is oil or grease on any bolt or nut, clean before installing wheel nuts.

Lower the vehicle completely and tighten the wheel nuts using the wheel nut spanner. Turn the jack operating lever counter clockwise using the wheel nut spanner to lower the vehicle, making sure the handle remains firmly fitted onto the jack handle extension. Do not use other tools or any additional leverage other than your hands, such as a hammer, pipe or your foot. Make sure the spanner is securely engaged over the nut. Tighten each nut a little at a time in the diagonally opposite order. Repeat the process until all the nuts are tight.

Improperly or loosely tightened wheel nuts are dangerous. The wheel could wobble or come off. This could result in loss of vehicle control and cause a serious accident. Always make sure all the wheel nuts are properly/securely tightened to the specified torque.

When lowering the vehicle, make sure all portions of your body and all other persons are clear off the vehicle as it is lowered to the ground. Have the wheel nuts tightened with the torque spanner to 83 -104Nm, as soon as possible after changing wheels.

Put the wheel cover into position aligning the nozzle on the wheel to the nozzle clearance on the wheel cover. Tap it firmly on the sides with your hand to snap it into place.

2.6.5 Restore all the Tools, Jack and Flat Tyre Securely

Replace the tools (jack, wheel spanner, etc.,) in their storage locations.

Align the spare wheel bracket to the centre hub of the wheel. Winch up the flat tyre to the floor at the rear of the vehicle. Firmly tighten the securing nut and put the floor carpet back.

Double check to ensure the tyre is snug against the rear floor of the vehicle. The spare wheel bracket/cable may be damaged if the vehicle is driven with the spare wheel loosely mounted.

Drive slowly to the nearest service station and inflate to the correct pressure. Always reinstall the valve cap after checking or adjusting tyre pressure, dirt and moisture could get into the valve core and cause air leakage or valve damage.

2.7 Identifying Components in the Engine Compartment

2.8 Technical Specifications

2.9 Vehicle Identification Number (VIN)

Vehicle Identification Number (VIN) is the legal identity of your vehicle. The vehicle identification number is stamped on the VIN plate riveted on to the bottom of the B-Pillar on the driver side.

2.10 Engine Number

The engine number is punched on the LHS face of the crankcase adjacent to the water pump. The engine number is also stamped on the VIN plate near the bonnet release lever.

3 VEHICLE OVERVIEW

3.1 Front Overview

3.2 Rear Overview

3.3 Instrument Panel Overview

4 INSTRUMENT CLUSTER OVERVIEW

4.1 Instrument Cluster

4.2 Warning Lamps Overview

4.3 Warning Lamps

Symbol	Warning Lamp/Tell Tale	Lamp Pre-check	Lamp Status while Engine running	Action/Remarks
	Seat Belt Warning Lamp	Yes	Continuously ON	If tell tale is not turning OFF even after fastening the seat belt, contact an Authorized Mahindra Dealer for assistance
	Left Turn Indicator	No	Slow or Fast Blinking	Indicates left turn lamp is blinking Slow Blinking: Normal operation Fast Blinking: One /more left turn lamp bulb has fused. Have the bulb replaced
	Airbag Warning Lamp *	For about 2 seconds	Continuously ON	Indicates malfunction of the airbag system. Contact an Authorized Mahindra Dealer immediately
	Parking Lamp	No	Continuously ON	Indicates Parking Lamp is ON
	Low Fuel Warning Lamp	No	Continuously ON	Indicates fuel level has reached the reserve level. Re-fuel immediately.
	Glow Plug Indicator	For about 2 seconds	Continuously ON	Indicates a malfunction in the starting system. Contact an Authorized Mahindra Dealer immediately
	Vehicle Armed Status Lamp	No	Blinking	Slow Blinking: Vehicle is armed with the remote Fast Blinking/Continuously ON: Indicates a system malfunction. Contact an Authorized Mahindra Dealer immediately
	High Coolant Temperature Warning Lamp	Yes	Continuously ON	Engine temperature very high. Contact Authorized Mahindra Dealer immediately
	Water in Fuel Filter Warning	Yes	Continuously ON	Indicates water in fuel filter. Drain the water from filter or contact an Authorized Mahindra Dealer for assistance
	Right Turn Indicator	No	Slow or Fast Blinking	Indicates right turn lamp is blinking Slow Blinking: Normal operation Fast Blinking: One /more right turn lamp bulb has fused. Have the bulb replaced
	Low Engine Oil Pressure Warning Lamp	Continuously ON till Engine Starts	Continuously ON	Indicates engine oil pressure is low. Check oil level and top-up or contact an Authorized Mahindra Dealer for assistance
	Check Engine Lamp	For About 2 Seconds	Continuously ON or Blinking	Indicates a potential malfunction in the EMS, contact an Authorized Mahindra Dealer immediately
	Parking Brake ON/Brake Fluid Low Warning Lamp	Yes	Continuously ON	Either one of below conditions- 1. Park Brake might be engaged 2. Brake fluid level might be low 3. Front Brake Pads are worn Contact Authorized Mahindra Dealer immediately for assistance
	OBD Check Lamp	Continuously ON till Engine Starts	Continuously ON	There is a potential malfunction related to emission system, contact an Authorized Mahindra Dealer immediately
	Headlamp High Beam Indicator	No	Continuously ON	Indicates Head lamp high beam is ON
	Stop/Start Lamp	No	Continuously ON or Blinking	Continuously ON: Engine is in auto stop mode Blinking: Stop/Start is about to stop the engine
	ABS Warning Lamp *	For About 2 Seconds	Continuously ON	Indicates malfunction of the ABS system. Contact an Authorized Mahindra Dealer immediately
	Charging System Warning Lamp	Continuously ON till Engine	Continuously ON	Indicates malfunction in charging system. Contact Authorized Mahindra Dealer for assistance
	Door Ajar Warning Lamp	No	Continuously ON	Indicates one or more doors and/or boot/hood are open

5 SEATS AND SEAT BELTS

5.1 Front Seats

5.1.1 Sitting in Correct Position

Follow the tips below for a comfortable and safe journey;

• Sit in an upright position with the base of your spine pressed against the seat back
• The driver and front passenger seat head restraint has 5 positions. Adjust it as close as possible to the above specified position, with the top of the head restraint even with the top of your head
• Maintain sufficient distance between yourself and the steering wheel. Maintain at least a ten inch (10") distance from the centre of the steering wheel to your chest
• The top curve of the steering wheel should align with your chin for ideal road visibility
• Adjust your seat and seat back angle such that your wrists rest on the steering wheel
• Ensure your legs are in bent position while fully depressing the clutch pedal.

The seat should be adjusted while still maintaining control of the foot pedals (able to fully depress the clutch pedal), steering wheel (rest the wrists on the steering wheel) and your view of the instrument panel controls.

Never adjust the driver's seat while the vehicle is in motion. The seat may unexpectedly move and cause the driver to unintentionally operate the accelerator or brake, or turn the steering wheel, causing loss of control of the vehicle, an accident or serious personal injury. Adjust the driver's seat only when the vehicle is not in motion.

Never put objects under the seats. They may interfere with the seat-lock mechanism or unexpectedly activate the seat position adjusting lever, causing the seat to suddenly move, resulting in loss of control of the vehicle, an accident or serious personal injury.

While adjusting the seat, do not put your hands under the seat or near the moving parts. This may lead to injuries.

5.1.2 Front Seat Slide

Move the seat forward or backward by lifting the adjustment lever located under the seat front and release once the desired position is reached.

While adjusting the seat, make sure the latch engages fully and the seat is locked firmly in the desired position. An unlocked seat may move in a sudden stop or collision, causing injury to the person in that seat. Push and pull on the seat to be sure it is locked.

5.1.3 Front Seat Recline

To adjust the seat back, lift the lever located on the outboard side of the seat, lean back, and release the lever at the desired position. To return the seat back, lift the lever, lean forward, and release the lever.

The seat belts provide maximum protection in a frontal or rear collision when the occupants are sitting up straight and well back in the seats. If you are reclined, the lap belt may slide past your hips and apply restraint forces directly to the abdomen, or the shoulder strap may contact your neck. The more the seat is reclined, the greater the risk of serious injury.

When returning the rear-reclined seat back to its upright position, make sure you support the seat back while operating the lever.

5.1.4 Front Seat Height Adjustment

The driver seat height can be raised or lowered to three positions.

To RAISE the seat height, lift the seat height adjust handle while there is no load or prior to occupying the seat. Release the lever once desired seat height is reached.

To LOWER the seat height, lift the seat height adjust handle while seated in the driver seat. Release the lever once desired seat height is reached.

5.2 Head Restraint

The head restraint comprises of the padded portion which contacts your head and is inserted/locked in receptacles on the top of the seat back.

Your vehicle seats are equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of rear collision.

The head restraint can be pulled out completely by depressing the locking button while pulling the restraint out.

Align the head restraint shafts over the holes on the seat top and push the restraint straight down till you hear the lock click.

Keep the seat back as upright as possible so the headrest is behind, not beneath, and almost touching your head.

Never drive with the head restraints not properly adjusted, head restraints removed or inserted in a flipped condition. With no support behind your head, your neck could be seriously injured in a collision.

Head restraints are provided for the front row and second row outboard occupants.

5.3 Second Row Seats

Loading luggage on the seats is dangerous. The luggage can become a projectile that could hit and injure passengers in a sudden stop or collision. Luggage should always be kept on the floor.

To avoid serious injury, do not sit on or place objects on a folded seat back while the vehicle is moving.

5.3.1 Second Row Seat Recline

To change the second row seat back angle, lean forward slightly while raising the recline lever on the top corner of the seat back, lean back to the desired position and release the recline lever. Make sure the recline lever returns to its original position and the seat back is locked in place by rocking the seat back forward/backward.

When returning the rear-reclined seat back to its upright position, make sure you support seat back while operating the lever.

5.3.2 Second Row Seat Folding (Third Row Seat Access)

The second-row seat can be flipped forward to provide more cargo space.

• Lower the second-row seat head restraint to the lowest position (else it will obstruct and hit the floor)
• Insert the lap belt into the pocket of the seat bottom
• Recline the seat back to full forward direction

• Push side actuation lever (B) in forward direction for Ingress, OR
• Pull rear actuation lever (A) for Egress

• Push seat back to rear side of vehicle for locking
• Pull seat back for upright position till it locks in design position
• Push seat cushion downward by sitting on it (>45 kg) for locking seat cushion

Return the seat back to its upright position in one continuous motion to securely lock the seat and in turn avoiding seat flipping forward suddenly leading to injuries. If this happens, release the seat lock by pulling the lever and repeat the procedure.

Be cautious when placing your hands around the seat anchors. You could pinch your hands or fingers between the seat anchor and the seat. Hold the edge of the seat when lowering it into place. Never place your hands between the seat anchor and the seat.

5.4 Third Row Seats

Access to or exit from third row seat and luggage area is possible by completely folding the second row seat. Second row seat features 60:40 split configuration. Instead of folding the complete seat back and seat cushion, the required seat alone can be folded to gain access to third row seat.

Refer to the previous sections for details regarding folding of second row seats.

5.4.1 Third Row Seat Folding

To fold the third row seat, unlock the seat back by pulling the lever on the rear of the seat back outwards.

Similarly lower the other half of third row seat to get a completely flat surface.

Both the second row and third row seats can be folded flat to maximise the luggage space.

5.5 General Warnings and Instructions- Seat Belts

At least once each month, inspect the seat belt webbing for any cuts, tears, or other signs of wear (such as fraying along the edges). Also inspect the anchors, retractors, and buckles to be sure they are tight and operational.

• All occupants, including the driver, should always wear their seat belt no matter how short the trip in order to minimize the risk of severe injury in the event of a crash. In an accident, an un-belted passenger becomes a projectile, and can cause serious injury to himself or another passenger.
• In a rollover crash, an un-belted person is significantly more likely to die than a person wearing a seat belt
• Some people believe that wearing a seat belt will lead to entrapment in the vehicle after an accident. However, your chances of surviving the initial impact, being able to unbuckle yourself and escaping from the vehicle is much greater if you are belted.
• In order to be properly buckled, you must always sit up straight and keep your feet on the floor in front of you. The lap part must be worn low and tight across your hips, just touching the top of your thighs. While fastening the seat belt, the shoulder strap of the seat belt must pass over your chest and top of your shoulder. It must never touch your neck, face, the side of your shoulder, arm, or pass under your arm. The belt must always be flat against your body and not twisted in any way. Nothing, such as an arm rest, a pocketbook, or any external objects should be between you and the seat belt. Improper wearing of a seat belt will reduce the protection in an accident.
• Seat belts should be adjusted as tightly as possible, consistent with comfort to properly secure the wearer in the seat. A slack belt will greatly reduce protection to the user, and could cause additional injuries.

• The seat belts provided for your vehicle are designed for people of adult size, must be properly used and maintained.
• Passengers should not move out of or change seats while the vehicle is moving. A passenger who is not wearing a seat belt can be thrown against the inside of the vehicle, against other occupants, or out of the vehicle during a crash or emergency stop
• Do not use any accessories on seat belts or modify in any way the seat belt system. Devices claiming to improve occupant comfort or reposition the seat belt can reduce the protection provided by the seat belt and increase the chance of serious injury in a crash
• An accident or emergency stop, can damage your seat belt system, even if the accident is “minor”. Please have your Authorized Mahindra Dealer inspect the seat belt system after an accident
• Please be aware that any unsecured item in your vehicle, such as your pet, unsecured child restraint system, or a laptop, can become a projectile in the event of an accident or sudden stop, causing injuries to occupants in the vehicle

Never use a damaged seat belt system. A damaged seat belt will not provide protection in an accident, resulting in serious injury.

• Seat belt systems can be prone to abuse. They are not indestructible. They must be handled with care to avoid damage
• Keep the belts clean and dry. Belt retraction may become difficult if the belts and webbing are soiled. If they need cleaning, use a mild soap solution or lukewarm water. Never use bleach, dye, or abrasive cleaners. These chemicals will severely weaken the belts
• Retractors in 3-point type seat belts retract the seat belts when not in use. The inertia lock and coil spring allow the belts to remain comfortable on users during normal driving. During accidents or abrupt stops, inertia locks restrict the sudden forward movement of the wearer

Seat Belts - Patients

Persons with serious medical conditions should also wear a seat belt. Consult your doctor for specific recommendations before travel.

Seat Belts - Pregnant Women

Pregnant women must also wear seat belts. Consult your doctor for specific recommendations.

The lap belt should be worn snugly and as low as possible over the hips. The shoulder belt should be worn across your shoulder, but never across the stomach area. When worn properly, the seat belt will protect both the mother and the foetus in an accident or emergency stop.

A pregnant woman should never wear the seat belt across the stomach area. This could lead to serious injuries to the foetus and/or the pregnant mother.

Never ride with the seat back reclined so that the seat belt is no longer resting against your chest. The seat belt provides maximum protection in a frontal or rear collision when the occupants are sitting up straight and well back in the seats. If you are reclined excessively, the lap portion of the belt may slide past hips and apply restraining forces directly to the abdomen, or the shoulder portion of the belt may contact the neck. The more the seat is reclined, the greater the risk of serious injury.

Never wear twisted seat belts. Excessive forces will be transferred from the belt to the wearer, in a collision, resulting in serious personal injury.

Each seat belt is meant for use by one person only. Using one seat belt for more than one person at a time is dangerous. The seat belt will not be able to spread the impact forces properly leading to serious injuries.

Never put a belt around a child being carried on the occupant's lap. This could lead to serious injuries. The child may be crushed in an accident or emergency stop.

• Reduce the possibility of being thrown from your vehicle
• Reduce the possibility of injuries to lower body and legs during an accident
• Hold the driver in a position which allows better control of the vehicle

Children who are too large for child restraint systems should always occupy the rear seat and use the vehicle seat belts. The lap portion should be fastened snug on the hips and as low as possible and the shoulder strap should be across the child's shoulder, not the neck or face. If you are unable to position the strap across the child's shoulder, the child should remain in a booster seat. Frequently check the seat belt to be sure it remains snug and in position. A squirming child could cause the seat belt to come out of position.

5.6 Fastening the Seat Belt (3-Point type)

Adjust the seat as needed, sit up straight and well back in the seat. To fasten your seat belt, pull the webbing out of the retractor and insert the metal tab into the buckle. An audible “click” would be heard when the tab locks into the buckle. Pull up on the shoulder strap to tighten the lap belt across your hips. The seat belt retractor will pull in any slack in the shoulder strap. A slow and easy motion will allow the belt to extend and let you move your body around freely.

Periodically check the seat belt as you ride to be sure it remains snug and in position. If there is a sudden stop or impact, the belt will lock into position. It will also lock (restrict) if you try to lean forward too quickly.

If the driver or co-driver seat belt is not fastened when the ignition is switched ON, the seat belt warning lamp illuminates. Refer “Warning Lamps” in the “Features and Control” chapter for further details.

5.7 Fastening the Seat Belt (2-Point Lap type)

This seat belt is applicable to the second row middle passenger seat. Insert the tongue into the buckle until it snaps. Position the lap belt on the hips as low as possible.

5.8 Unfastening the Seat Belt (both 3-Point & 2-Point)

To release the belt, press the buckle release button and allow the belt to retract. If the belt does not retract smoothly, pull it out and check for kinks or twists. Then make sure it remains untwisted as it retracts.

Never insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and may cause damage to the buckle mechanism, thereby making the seat belt ineffective in an accident, resulting in serious personal injury.

5.9 Seat Belt Height Adjuster

You can adjust the height of the shoulder belt anchor for maximum comfort and safety in both front seats. If the height of the seat belt is too near your neck, you will not be getting the most effective protection. The shoulder portion of the belt should be adjusted so that it lies across your chest and midway over your shoulder nearest to the door and not your neck.

To adjust the height of the seat belt anchor, lower or raise the height adjuster to an appropriate position while pressing the height adjuster button. Release the button to lock the anchor into position. Try sliding the height adjuster to make sure that it has locked into the position.

Adjust the shoulder belt height sitting well back in the seat. Do not adjust the seat belt height while vehicle is in motion.

5.10 Child Restraint System (CRS) (if equipped)

Use a child restraint system only if the child is not big enough to properly wear the seat belts. Else, use the regular seat belt instead of the child restraint system. Seat the child in the rear seat and use the seat belt. According to accident statistics, children are safer when properly restrained in the rear seat than in the front seat. Always secure a child in a proper child restraint system in accordance with age and size of the child as recommended by the child restraint system manufacturer.

Do not allow children to stand up or kneel on either the rear or the front seats. An unrestrained child could suffer serious injuries during emergency braking or collision.

It is also not recommended that children travel sitting on your lap as it does not provide sufficient restraint.

6 SUPPLEMENTAL RESTRAINT SYSTEM (SRS) (if equipped)

6.1 Airbag

• One frontal airbag for the driver
• One frontal airbag for the front passenger

6.1.1 Airbag Location

• In the steering wheel hub - Driver Airbag


• Above the upper glove box - Passenger Airbag

An airbag is not designed to deploy in every type of crash. Depending on the type of accident or impact, the front airbag’s, side airbag’s and curtain airbag’s independently deploy thereby protecting the occupants.

To minimize the risk of severe injury in the event of a crash, every passenger must always wear their seat belt (see the chapter on Seat Belts in this manual). The airbag’s inflate very quickly with great force. Do not position any part of your body too close to a airbag, you or especially children could be seriously injured by a deploying airbag.

6.2 Introduction

The Supplemental Restraint System (SRS) includes airbags, pre-tensioners and ECU. The airbags are designed to provide further protection to the vehicle occupants in addition to the primary protection provided by the seat belts and seat belt pre-tensioners.

The primary components of the system are the sensors which measure the crash severity. In the event of a significant frontal impact, the SRS airbags inflate to work in conjunction with the seat belts and help reduce injuries mainly to the driver's or front passenger's head/chest.

Seat belts are the primary restraint system in the vehicle. An airbag provides supplemental protection in addition to the seat belts.

All occupants, including the driver, should always wear their seat belts irrespective of presence of airbags to minimize the risk of severe injury in the event of a crash.

Airbags are more effective in reducing injuries when the seat belts are worn.

6.2.1 Driver and Front Passenger Air Bag

Your vehicle is equipped with a Supplemental Restraint System (Airbag) and lap/shoulder belts at both the driver and front passenger seating positions. The indications of the system's presence are the letters “SRS AIR BAG” embossed on the airbag pad cover in the steering wheel and the passenger's side front panel pad above the glove box.

The SRS is designed to deploy the front airbags only when an impact is sufficiently severe and when the impact angle is less than ± 30° from the forward longitudinal axis of the vehicle.

Front airbags are not intended to deploy in side-impact, rear impact or rollover crashes. In addition, front airbags will not deploy in frontal crashes which are below the prescribed deployment threshold where risk of serious injuries is low.

Do not place any objects over the airbag or between the airbag and yourself.

6.2.2 Airbag System Malfunction Lamp

Airbags do not require any regular maintenance of service. The airbag system malfunction lamp illuminates when the ignition is ON, and it turns OFF after about two seconds as self check confirming normal operations of airbag system and malfunction lamp.

This lamp monitors airbag sensor assembly, airbag sensors, indicator lamp, seat belt pre-tensioner assemblies, inflators, interconnecting wiring and power sources.

If either of the following conditions occur, there is a malfunction of the airbags or seat belt pre-tensioner. Immediately contact your Mahindra Dealer.

• The lamp does not glow when the ignition is switched ON or glows beyond six (6) seconds after switching the ignition ON
• The lamp comes ON at any other time, even briefly
• The lamp comes ON intermittently

Never make any modifications to your vehicle which could affect the performance of your airbag system. In particular, changes to the vehicle frame, bumpers, bull bar, front fenders, ride height, suspension, seat belts, interior trim, seats or steering wheel (especially covers, pads or other trim), could prevent proper deployment of the airbag. If you need to make any modifications to accommodate any disability you may have, please contact your authorized Mahindra dealer.

Never try to open or strike the airbag cover. If the airbag cover is cracked or damaged in any way, the airbag may not function as intended. Take the vehicle to an Authorized Mahindra Dealer.

Even if the airbags do not deploy during an accident, take your vehicle to an authorized Mahindra Dealer for a thorough inspection of the airbag and seat belt systems, no matter how minor the accident. The airbag system could have been damaged, and may not work as intended in the future, resulting in serious injury.

6.2.3 Airbag Inflation/Deployment

The airbag sensors constantly monitor the forward deceleration of the vehicle. If an impact results in a forward deceleration beyond the designed threshold level, the system triggers the airbag inflators. This initiates a chemical reaction which quickly fills the airbags with non-toxic gas.

Upon deployment, tear seams molded directly into the pad covers separate under pressure from the expansion of the airbags. Further opening of the covers allows full inflation of the airbags. A fully inflated airbag, in combination with a properly worn seat belt, slows the driver's or the passenger's forward motion, reducing the risk of head and chest injury.

After complete inflation, the airbag immediately starts deflating, enabling the driver to maintain forward visibility and the ability to maneuver or operate other controls.

Deployment of the airbags happen in a fraction of a second, producing a loud noise releasing a ‘white smoke’ and residue along with a non-toxic gas. This does not indicate a fire. This smoke may remain inside the vehicle for some time, and may cause some minor irritation to the eyes, skin or breathing. Be sure to wash off any residue with soap and water as soon as possible to prevent any potential skin irritation. If you can safely exit the vehicle, you should do so immediately.

• Do not modify, remove, strike or open the seat belt pre-tensioner assemblies, airbag sensor or surrounding area or wiring. Failure to follow these instructions may prevent them from activating correctly, cause sudden operation of the system or disable the system, which could result in serious injury.
• Parts of the airbag module (steering wheel hub, airbag cover and inflator) may be hot for several minutes after deployment. The airbags inflate only once
• Do not cover the steering wheel, instrument panel, seats with any object (e.g. dash panel covers, seat covers) which may prevent the airbags from inflating properly
• The airbags inflate with considerable force. While the system is designed to reduce serious injuries, primarily to the head and chest, it may also cause other, less severe injuries to the face, chest, arms and hands. These are usually in the nature of minor burns or abrasions and swelling, but the force of a deploying airbag can also cause more serious injuries, especially if an occupant's hands, arms, chest or head is in close proximity to the airbag module at the time of deployment. Sit straight and well back into the seat. Move your seat as far back as practical to allow room for airbag inflation, while still allowing you to properly operate/drive the vehicle
WARNING
• The front passenger should never sit on the edge of the seat, stand near the glove compartment, rest feet or other parts of the body on the dashboard when the vehicle is moving.

WARNING
• The driver or front passenger who is too close to the steering wheel or dashboard can be seriously injured during airbag deployment.
• The driver must sit as far back as possible from the steering wheel while still maintaining control of the vehicle
• The front passenger must sit as far back as possible from the dashboard
• Sitting improperly or out of position can cause occupants to be shifted too close to a deploying airbag, strike the interior structure or be thrown from the vehicle resulting in serious injury

• Always sit upright with the seat back in an upright position, on the seat cushion centre with your seat belt on, legs comfortably extended and your feet on the floor
• All vehicle occupants must be properly restrained using the seat belts
• All infants and children must be placed in the rear seat of the vehicle in a child restraint seat and be properly restrained by seat belts
• Front airbags can injure occupants improperly positioned in the front seats
• Even with airbags, improperly belted and un-belted occupants can be severely injured when the airbag inflates. Always follow the precautions about seat belts, airbags and occupant safety contained in this manual
• Do not modify the front seats. Modification of the front seats could interfere with the operation of the supplemental restraint system or side impact airbags
• Do not place items under the front seats. Placing items under the front seats could interfere with the operation of the supplemental restraint system sensing components and wiring harnesses

6.2.4 Child Restraint and Airbag

Never place a rear-facing child restraint in the front passenger’s seat. If the airbag deploys, injuries to the child may be fatal..

In addition, do not place front-facing child restraints in the front passenger’s seat either. If the front passenger airbag inflates, it could cause serious or fatal injuries to the child.

• Extreme Hazard! Do not use a rear facing child restraint on a seat protected by an airbag in front of it!
• Never put a child restraint in the front passenger’s seat. If the front passenger airbag inflates, it can cause serious or fatal injuries.
• Never hold an infant or child on your lap. The infant or child could be seriously injured in the event of a crash. All infants and children should be properly restrained in appropriate child safety seats or seat belts in the rear seat.
• Install the child restraint system on the rear outboard seats, and securely lock the child restraint system in position.
• Always Buckle Children (ABC) in the back seat. It is the safest place for children of any age to ride.

6.2.5 Airbag Deployment

The images shown in this section are for illustrative purpose only. They may not look like your model/variant or vehicle.

Front air bags are designed to inflate in a frontal collision depending on the intensity, speed or angles of impact of the front collision.

Airbag Non-deployment

Impacts below a pre-determined threshold level may not cause the airbag’s to deploy in the following cases:

Air bags may not inflate if the vehicle collides with objects such as utility poles or trees, where the point of impact is concentrated to one area and the full force of the impact is not delivered to the sensors.

Running under a truck's tail gate may not provide the decelerations necessary for airbag deployment. Air bags will not inflate in this “under-ride” situation where deceleration forces that are detected by sensors are significantly low.

Frontal air bags are not designed to inflate in rear collisions, where occupants are moved backward away from the airbags by the force of the impact. In this case, inflated air bags would not be able to provide any additional benefit.

Frontal impact beyond 30º range from head-on to the vehicle.

Driving into a big pot-hole, stepped surface or hitting the far side of a hole/incline will not inflate the airbag.

Air bags will not inflate in rollover accidents where air bag deployment would not provide protection to the occupants. However, side impact and curtain air bags may inflate when the vehicle is rolled over by a side impact collision.

Frontal offset impact to the vehicle may not provide the deceleration force necessary for airbag deployment. In an angled collision, the force of impact may direct the occupants in a direction where the air bags would not be able to provide any additional benefit, and thus the sensors may not deploy any air bags.

6.2.6 Airbag Replacement

Self-servicing or tampering with the airbag system is dangerous. An airbag could accidentally deploy causing serious injuries, or will not deploy when there is a need. Always take your vehicle to an authorized Mahindra dealer for inspection and repairs.

6.2.7 Self Removing SRS Related Parts

Self removing the instrument panel, steering wheel, seats or airbag related parts or sensors is not recommended. Airbags could accidentally activate and cause serious injuries, or they may not deploy when there is a need. Visit an authorized Mahindra dealer if these parts must be removed.

6.2.8 Airbag Disposal

Improper disposal of an airbag or a vehicle with live airbags can be extremely dangerous. Approach an authorized Mahindra dealer to do these jobs.

6.2.9 Airbag Repair

If the front airbag cover or IP airbag cover shows signs of damage or having been removed, the vehicle should be towed to the nearest authorized Mahindra dealer for repair. Do not attempt to self repair or reinstall the cover.

6.2.10 Airbag Maintenance

For cleaning the airbag covers/areas, use only a soft dry cloth or one which has been moistened with plain water. Solvents or cleaners could adversely affect the airbag covers and proper deployment of the system.

7 LOCKS AND KEYS

XUV500 comes with two keys. Your key number is given on the tag attached to the key. It is recommended that you record the key number and store in a safe place. The keys operate all locks in your vehicle including those of the doors and ignition with steering lock. We advise you to keep one of these keys at a safe place for emergency use, but not in the vehicle.

Press the key release button on the RKE to unfold the key.

Never leave the key in the ignition switch with children in the vehicle. A child could switch on the ignition, start the engine, operate power windows and other controls, or move the vehicle, resulting in personal injuries to the bystanders and/or children seated inside.

7.1 Doors

7.1.1 To Open a Door from Inside

Pull the door lever away from the door and push the door outward to open.

7.1.2 To Open a Door from Outside

Pull the door handle firmly outwards to unlock and swing the door open.

7.1.3 Locking/Unlocking Individual Doors from Inside

Individual doors can be locked/unlocked from inside by the respective door lock tabs. Lift the lock tab outwards to unlock or press the tab inwards to lock that particular door.

Locking the driver door from inside activates the central locking system, thereby locking ALL the doors of the vehicle. Refer to Central Locking section for further details.

7.1.4 Manual Locking/Unlocking Doors from Outside

The driver/co-driver door can be manually locked/unlocked from outside by using RKE. Open the key by pressing the key release button on the RKE. The key is bi-directional; you can insert it into the key hole either way. Turn the key anticlockwise to lock or clockwise to unlock the door.

A key hole is provided in the driver door and front passenger door, to lock/unlock the doors manually from outside.

Locking the driver door from outside activates the central locking system, thereby locking ALL the doors of the vehicle. Refer to Central Locking section for further details.

7.1.5 Locking/Unlocking the Back Door

The back door can be manually unlocked by pressing the unlock button under the rear applique.

To close the back door, lower the back door half way down and allow it fall on its own weight. The door is locked automatically

7.2 Central Locking System

All doors of the vehicle can be simultaneously locked or unlocked from the driver door.

7.2.1 Central Locking/Unlocking All Doors from Outside

To manually lock/unlock all the doors from outside using the RKE, turn the key anti-clockwise (A)/clockwise (B) respectively in the driver door key hole.

In case the back door is open when the central locking is activated, the back door will not be locked even if it is closed later.

If any other door is open when central locking is activated, the system locks the open doors when they are closed.

7.2.2 Central Locking/Unlocking All Doors from Inside

Press the driver door lock tab down (A) to lock or lift the lock tab up (B) to unlock all doors simultaneously.

7.2.3 Child Safety Rear Door Lock

Your vehicle is equipped with left and right side child safety rear door locks. When the lock mechanism is engaged, the rear door(s) cannot be opened from the inside. The door(s) can only be opened from the outside.

To activate the child safety right rear door lock push the lever down (A) till you hear a distinct click indicating the activation of the child lock.

To de-activate the child safety right rear door lock pull the lever up (B) till you hear a distinct click indicating the deactivation of the child lock.

If the rear doors are not operable from inside, ensure that the child safety locks have been disabled.

Mahindra strongly recommends that the child safety rear door locks be used whenever there are children traveling in the rear seat.

7.3 Remote Keyless Entry (RKE) System

The front side of the RKE has three control buttons; Unlock, Lock and Search buttons. There is also a mechanical key release button (D). The Remote Keyless Entry (RKE) system operates on Radio Frequency (RF). You can insert the key into the ignition with either side up.

7.3.1 Precautions while handling RKE:

• Do not cover the key grip with any material that cuts off RF waves
• Do not leave the key exposed to high temperatures for a long period, such as on the dashboard or hood under direct sunlight
• Do not put the key in any liquid or wash it in an ultrasonic washer

7.3.2 To Lock and Arm the Vehicle with RKE

Press the lock button on the RKE for locking and arming the vehicle. When the vehicle is successfully locked and armed using the RKE, the hazard lamps flash once. If there are any open doors, the hazard lamps flash five times along with audible beeps indicating the same.

The audible beeps heard during the door open status can be muted/unmuted by pressing the lock button on the RKE for more than 3 secs.

• If any of the doors, except the driver door, are open while locking the vehicle with RKE, the vehicle locks all doors (door locks) irrespective of the open door/doors. When the open door(s) is/are closed later, the vehicle is locked and armed.
• If the driver door is open while locking the vehicle with RKE, the vehicle is not locked or armed. Close the driver door and lock the vehicle again with RKE to arm the Anti-theft system.

7.3.3 Unlock and Disarm the Vehicle with RKE

Press the unlock button on the RKE to unlock and disarm the vehicle. When the vehicle is unlocked and disarmed using RKE, hazard lamps flash twice

7.3.4 Theft Alarm

If there was an unauthorized attempt to open/start the vehicle by someone from the time you had locked and armed the vehicle to the time you press the unlock button of RKE, the hazard lamps flash four times along with an alarm indicating the attempt. If this occurs, press the “UNLOCK” button on the RKE to disarm the security alarm.

Using the ignition key to open the door, when the vehicle was locked and armed with RKE will be treated as unauthorized by the system setting off the alarm.

When vehicle is armed by RKE, opening the door from inside by operating the door inner handle will activate the vehicle theft alarm.

Press the unlock button on the RKE to cancel the alarm.

7.3.5 Back Door Open

Press the back door open button on the RKE to unlock the back door. The hazard lamps flash four times indicating the same.

7.3.6 Search Function

The search function can be used to locate the vehicle in a parking lot. Press the unlock button on the RKE for more than 3 sec. continuously to activate the search function.

When the Search function is ON, the hazard lamps flash for approx. 30 sec. helping you to locate your vehicle. To extend the search, press the search button again which will flash the hazard lamps for another 30 sec. You can turn it OFF by pressing the unlock button.

The head lamps also turn ON when UNLOCK button is pressed twice (enabling the LMV feature). For the first UNLOCK command, the doors are unlocked, and for the next UNLOCK command, the head lamps turn ON enabling you to safely board/locate the vehicle in the night.

Search function works both during Locked/Unlocked conditions of the vehicle.

7.3.7 Mute/Un-mute the Alarm/Beeps

The alarm or beeps heard when one of the doors are open can be muted/un-muted. Press the lock button for more than 3 sec. to swap between mute and un-mute.

The beeps heard during the door open situation can be muted/unmuted. There are NO BEEPS during normal locking/unlocking of doors.

7.3.8 Panic Alarm Function

The panic alarm function can be used during emergencies to draw the attention of onlookers/bystanders. Press the unlock button on the RKE for more than 3 sec. continuously when the key is in the ignition to activate the panic alarm.

7.3.9 Auto Locking

When the vehicle crosses 20 kmph road speed range with all the doors closed properly, all doors are locked automatically.

7.3.10 Auto Unlocking

All the doors are unlocked automatically, when the vehicle has halted and ignition switched OFF. If the ignition is not switched ON for the next few seconds, all the doors are locked due to auto locking, provided doors are not open.

7.3.11 Auto Re-locking

Once you press the unlock button on the RKE, if you do not open any of the doors for the next 45 sec., all the doors are re-locked automatically.

In case of an accident/collision where a SRS has been activated (Eg. airbag), all the doors are unlocked automatically.

7.3.12 RKE Operating Range

Using RKE, you can lock/arm or unlock/disarm the vehicle from distances approx. 30ft.(9m).

If there is reduction in RKE range, please follow the steps below:

• Check the distance: The RKE may be too far from the vehicle. Stand closer to the vehicle during rain or bad weather
• Check the location: Other vehicles or objects may be blocking the signals. Take a few steps to the left or right, hold the RKE higher, and try again. Moreover, closeness to a radio transmitter such as radio station tower, airport transmitter, mobile or CB radios may lead to reduction in range of RKE
• Check the RKE battery: See battery replacement procedure, given later in this section
• If the RKE is still not working correctly, contact an Authorized Mahindra Dealer

7.3.13 RKE Battery Replacement

If the RKE operation is inconsistent when any of the buttons are pressed it indicates that the RKE battery is weak. The rear side of the RKE is snap fitted. Using a small screw driver or similar tool, pry or separate the two halves of the casing.

Pull out the batteries and discard the same. Insert new batteries of 3V type. While fitting the new battery, ensure the positive side of the batteries face up. Align both the halves of the RKE and press to snap fit. Check operation of the RKE.

While prying the RKE case, take care not to damage the battery. Do not touch the battery terminals or contacts.

Do not mix old batteries with new batteries. Replace BOTH the batteries when the RKE operation is weak.

Perchlorate material needs special handling and disposal. Refer to local regulations.

7.3.14 If RKE is Lost

If you have lost the programmed RKE, contact an Authorized Mahindra Dealer for procuring a new RKE.

While programming a new key set, you will have to submit all the keys available with you, to an Authorized Mahindra Dealer.

Please note that there is a limitation (max 2 keys at a time) to the number of keys that can be ordered. The minimum time frame required to supply the duplicate keys is 10 days after all the formalities are completed. Please contact the dealer to understand the formalities involved.

If you make your own duplicate key, you will not be able to deactivate the anti-theft devices or start the engine.

If the key is stolen or lost, communicate to Authorized Mahindra Dealer for de-activating the function of the lost or stolen key. This is essential to avoid unauthorized access using the misplaced key.

Only RKE transmitters programmed to your vehicle electronics can be used for remote locking and unlocking of your vehicle.

7.4 Engine Immobilizer System

An Engine Immobilizer System is a security system that prevents the vehicle being operated by an unauthorized person. The Engine immobilizer prevents the engine from being started unless it recognizes signals from the correct coded key. When a wrong key is inserted or a theft attempt is detected, the alarm is set off, and the hazard lamps flash along with a siren.

The system is automatically activated when the key is removed from the ignition.

7.4.1 Features of the Immobilizer System:

• Prevents the vehicle being started by anyone not in possession of the correct vehicle key
• The vehicle is automatically protected after the key is removed from the ignition. At every ignition ON, if the vehicle does not recognize the correct key code, the engine check lamp will be illuminate/blink and the engine cannot be started
• The vehicle will not be protected until the key has been taken out of the ignition

If the engine check lamp flashes or remains continuously illuminated after the ignition being switched ON, there is a system malfunction. Contact an Authorized Mahindra Dealer immediately.

Inserting the correct coded key in the ignition and switching the ignition ON, automatically deactivates the system. This enables the engine to start.

In the event of the vehicle not starting with the correct key, switch off the ignition for a minimum of 1 minute and attempt to start the vehicle again.

Do not modify, remove or disassemble the engine immobilizer system. Any unauthorized changes or modifications can affect proper operation of the system and will void your warranty.

The security system will be activated only when the vehicle is locked using the RKE. Locking the doors with the manual key will not activate the security system.

Using the ignition key to open the door, when the vehicle was locked and armed with RKE will be treated as unauthorized by the system setting off the alarm. Press the unlock button on the RKE to cancel the alarm.

8 FEATURES AND CONTROL

8.1 Quadruple Switch

The quadruple power window switch on the driver door armrest/handle controls the following functions;

• Both LH and RH ORVM folding
• ORVM selector
• ORVM adjustment
• Power window functions of all doors in the vehicle.
• Power window safety switch that enables/disables power window operation of other doors when operated independently from the respective doors

8.1.1 Power Windows

Power windows can be operated only when the ignition is “ON” position. The driver can operate all the power windows in the vehicle through the quadruple switch on the driver door armrest/handle. Other passengers in the vehicle can raise or lower their respective window glasses individually by using the separate switches provided on each of the door trim pads/arm rests.

To lower/raise the window glass push/pull the power window switches respectively.

Do not operate the power windows frequently when the engine is OFF. This will drain the vehicle battery.

If you operate the switches often during a short period of time, the system might become inoperable for a certain duration to prevent damage due to overheating. The system will return to normal functioning shortly. It is recommended to operate one window switch at a time.

While operating the power windows, check for obstructions like head, hand, etc. which may lead to personal injuries.

8.1.2 Power Window Lock Switch

The main power window quadruple switch in the driver door trim has a power window lock switch to enable or disable operation of rear passenger and front passenger window switches. To disable the rear or front passenger power windows, press the window lock switch down. To revert to normal operation, press the window lock switch again.

8.1.3 Auto/Express DOWN (driver side only)

Press the driver power window switch down for a moment and release. The glass moves all the way down automatically. You do not need to hold the switch till the glass comes down.

8.2 Mirrors

8.2.1 Manual ORVM (if equipped)

Integrated exterior rear view mirrors on both the sides facilitate maximum rear view information to the driver.

Fold both the ORVM’s manually while parking the vehicle in congested roads or narrow parking slots. This avoids hindrances and safeguards the ORVM’s.

8.2.2 Electric ORVM (if equipped)

The ORVM fold switch, ORVM adjustment switch (perimeter switch) and the Left (L)/Right (R) ORVM selector switches are located on the driver door trim/handle.

Both the ORVM’s can be electrically folded or unfolded by the pressing the ORVM fold button (A).

All ORVM controls work only when ignition is ON or engine is in running condition.

The ORVM folding/unfolding operation is limited to 2 times / minute.

The electric ORVM’s fold automatically when the vehicle is locked through RKE or unlocked through RKE and ignition switched ON.

Do not overestimate the distance of the objects that you see in the mirrors. Objects seen in convex mirrors are much closer than they appear.

Use the ORVM L/R selector switch, to select Left/Right side exterior mirror respectively. The ORVM adjustment switch adjusts the selected ORVM in the required direction. Lock the ORVM’s by setting the ORVM selector switch to the middle position.

8.2.3 Interior Mirrors

The interior rear view mirror provides the rear view information to the driver and also aids during reversing.

This mirror has day and night (anti-glare) positions. The night position reduces glare from head lamps of vehicles behind you. Flip the tab (A) on the bottom edge of the mirror to select the day or night position.

8.3 Sun Visor

Sun Visors are provided for both driver and co-driver above the windshield. The sun visors can be used for either frontal or sideward shade, to reduce glare or to shut out direct rays of the sun.

Pull down the sun visor to block the glare of the sun. The sun visor can also be swivelled to the side as shown.

The vanity mirror lamp will remain ON as long as the mirror flap/cover is open. This may lead to battery drain if left unchecked for long durations. Ensure the mirror flap/cover is always closed properly before folding back the sun visor in its position.

8.4 Utility Holders

Bigger objects, cans, etc., can be stored in the centre console storage. Unlock the centre console cover (which includes the upper tray console also) by unlocking the latch (B) and lift the console cover all the way up.

In select variants a cooler (air vents) is provided in the centre console storage. You can cool cans, small bottles, etc,. by opening the air vents at the bottom floor of the storage. Turn the cooler clockwise to open the air vents, or anti-clockwise to close the air vents.

8.4.2 Glove Box

There are two glove boxes on the co-driver side of the instrument panel.

• Upper Glove Box
• Lower Glove Box

The upper glove box can be opened by gently pressing the unlock push button (A). To close, gently lower the glove box lid and press to lock.

Do not overload the glove box.

Do not store loose or small metal objects inside glove box. This will lead to rattling while the vehicle is driven on bad roads.

The lower glove box is located just below the upper glove box. To open, gently press the unlock push button, and lower the lid. To close the glove box, raise the lid all the way up and gently press to lock the lid.

The lower glove box is illuminated automatically when it is opened and the light turns OFF when it is closed.

It is suggested to keep copies of all vehicle documents along with the owner’s manual kit in the glove box for reference when needed.

To avoid the possibility of injury in case of an accident or a sudden stop, both the upper and lower glove box lids should be kept closed when the vehicle is in motion.

8.4.3 Cup Holder

The cup holder located in the floor console between the front seats, It can be used for small cups or cans that are closed or have a lid.

Only sealed cups/cans with lid to be used in the cup holders.

Use caution when using the cup holders. A spilled beverage that is very hot can injure driver or passengers. Spilled liquids can also damage interior trim and electrical components. Any spilled beverage can also startle the driver and cause a loss of control of the vehicle resulting in an accident.

The second rows seats have an armrest embedded into the seat back. The arm rest can be unfolded and used as a cup holder.

Only sealed or cups with lid and cans to be used in the cup holders.

Use caution when using the cup holders. A spilled beverage that is very hot can injure the passengers and damage interior trim. Never place objects other than cups or cans in the cup holder. These objects can be thrown out in the event of a sudden stop or an accident, possibly injuring the passengers in the vehicle.

8.4.5 Third Row Cup Holder

The cup holders are located on both left and right side trims below the magazine holder.

Only sealed or cups with lid and cans to be used in the cup holders.

8.4.6 Bottle and Umbrella Holder

Bottle and Umbrella holders are located on both the front door lower trims. You can use them to store umbrellas, maps, papers, small books, bottles, etc.

NOTICE

Only sealed/closed bottles are to be used in the bottle holders.

8.4.7 Seat Back/Magazine Pocket

The seat back pockets are located on the back of the front seats for holding light weight papers/books/magazines, etc.

CAUTION

To avoid injury, do not place large or hard objects in the seat back pockets. Do not put more than 1 Kg weight in seat back pockets.

8.4.8 Third Row Magazine Pocket

The third row magazine pockets are located on the trims on either side of the third row seats. They can be used for holding light weight papers/books/magazines, etc.

CAUTION

Do not place large or hard objects in the magazine pockets. Do not put heavy objects in the magazine pockets.

There are two ticket, mobile or small object holders on either side of the front floor console.

8.4.9 Grip Handle

Foldable grip handles are provided above the front (passenger only), second row and third row outboard seats.

8.4.10 Coat Hook

The second row outboard passenger seats grip handles feature a coat hook for hanging your coat, shirts, etc.

NOTICE

Hang light weight articles only. Hanging excess/bulky weight/items may cause breakage of the hook and inconvenience to the passengers.

8.4.11 Horn

Press the pad on the steering wheel to blow/sound the horn. The horn functions even when the ignition has been switched OFF.

8.4.12 Interior Lamps

Interior lamps comprise of front/rear roof lamps, map reading lamps, ambience lamps and ignition key ring illumination. These lamps can be used for an illuminated entry. In auto mode, the roof lamps (courtesy lamps) and ignition key ring illuminate when any of the doors are opened. Once all doors are closed, the interior lamps switch OFF.

8.4.12.1 Front Roof Lamp

The front roof lamp is located above the interior rear view mirror. The roof lamp can be switched ON by the switch on the lamp.

8.4.12.2 Second Row Roof Lamp

The second row roof lamp is located on the roof above the second row seats. The courtesy lamp can be switched ON/OFF by the switch on the lamp.

8.4.12.3 Roof Lamp Operation

Both the front and second row roof lamps switch has three operation modes to choose from

A	Permanent ON	C	Permanent OFF
B	Door/Auto Mode

The roof lamp remains permanently ON in this position irrespective of the door open status

The roof lamp remains in DOOR/AUTO mode in this position.

The roof lamp remains permanently OFF in this position

The operation of the roof lamp in door mode is as follows:

• Roof lamp switches ON, dims and goes OFF after 10 sec delay during RKE unlock
• Roof lamp switches ON when any of the doors is/are open
• Roof lamp dims and goes OFF after 10 sec delay upon closing of all doors
• Roof lamp dims and goes OFF immediately on RKE lock after all doors are closed
• If any of the doors are not closed properly, the roof lamp switches OFF automatically after a preset duration
• Roof lamp goes OFF with ignition ON and all doors closed properly

NOTICE

The roof lamp will be turned ON in the case of an accident in a SRS equipped variant provided the roof lamp switch is in “Door” mode.

8.4.12.4 Battery Saver

The battery saver feature helps in switching OFF interior lamps that are inadvertently ON for long durations. This feature works only after the vehicle is locked with the interior lamp ON. If the vehicle is improperly closed/locked, the battery saver switches OFF the lamp after a duration of 3 mins.

8.4.13 Power Outlet

A 12V power supply socket provided for power take OFF. Electrical equipment/appliances like mobile phone charger, cigarette lighter, etc. can be used in the outlets.

NOTICE

The power sockets function only when the ignition is in ACC or ON positions. It is recommended to use the power sockets when the engine is ON to avoid battery drain.

The power outlet is located in the compartment below the centre bezel switch bank.

WARNING

To avoid serious injury:

• Close the power outlet cap when not in use
• Do not allow children to use or play with the power outlet
• When using electrical appliances, strictly follow the manufacturers instruction manual
• Never use the power outlet for electric heaters while sleeping
• Never insert foreign objects into the power outlet
• Never use malfunctioning electrical appliances
• Never insert inappropriate or badly fitting plugs into the power outlet

Do not modify, disassemble or repair the power outlet in any way. Doing so may result in unexpected malfunction or fire, which could cause serious damage to equipment and/or personal injuries. Contact an Authorized Mahindra Dealer for any necessary repairs.

WARNING

To prevent injuries and accidents, secure all electrical appliances before use. Do not use any appliance that may:

• Distract the driver while driving, or hamper safe driving
• Result in a fire or burn injuries due to the appliance rolling, falling or overheating
• Emit steam, while the windows of the passenger compartment are closed
NOTICE
• Use the power outlets only when the engine is running. Remove the plug from the power outlet after using the electric device. Using the power outlets when the engine is OFF or leaving the electric device plugged in for many hours may cause the battery to drain
• Do not use the power outlet to connect electric accessories or equipment that are not designed to operate on 12V
• Some electronic devices can cause electronic interference when plugged into the power outlet. These devices may cause excessive audio noise and may interfere with other electronic systems or devices in your vehicle

8.5 AUX Port

The AUX port is on the left side of CD input slot in the music system interface. You can connect i pods, etc., as an input and listen to the music through the vehicle speakers.

It is recommended to connect an input device only when the vehicle is stationary. Trying to connect an input device while driving may distract your attention and lead to accidents.

8.6 Exterior Lamps

The lighting control stalk is located on the right hand side of the steering wheel and is a part of the combination switch. It controls operations of parking lamps, head lamps, head lamp beam selection, high beam flashing, front/rear fog lamps and turn signals when the ignition switch is ON.

8.6.2 Turn Signals

8.6.3 Turn Signal - Right

• Push the lighting control stalk clockwise (to stop position B) to indicate a right turn. The instrument cluster arrow lamp pointing towards the right flashes along with the right side turn signal lamps (front, rear & ORVM) with chime indicating your intention of turning towards right

After you have completed your right turn, the stalk will automatically return to the neutral position switching OFF all the lamps.

8.6.4 Taking a Left turn

• Push the lighting control stalk anti-clockwise (to stop position A) to indicate a left turn. The instrument cluster arrow lamp pointing towards the left flashes along with the left side turn signal lamps (front, rear & ORVM) with chime indicating your intention of turning towards left
• After you have completed your left turn, the stalk will automatically return to the neutral position switching OFF all the lamps.
NOTICE

If the turn signal lamps on the instrument panel flash faster than normal, there may be a possibility that one or more of the turn signal lamp bulbs have blown. Replace the blown bulb immediately.

You can signal a lane change by moving the lighting control stalk clockwise or anti-clockwise to the limit point of free movement of the lever and releasing it once you change the lane.

Rotate the outer rotary switch on the lighting control stalk clockwise aligning the “arrow” on the stalk to “OFF” on the switch to switch OFF all lamps.

Rotate the outer rotary switch on the lighting control stalk clockwise aligning the “arrow” on the stalk to the “1st detente” position on the switch to switch ON the parking lamps.

The tail lamp, license plate lamp, instrument panel illumination lamps and all interior switches are also activated when the parking lamp is switched ON.

Rotate the outer rotary switch on the lighting control stalk clockwise aligning the “arrow” on the stalk to the “2nd detente” position on the switch to switch ON the head lamps.

Switch ON the head lamp, and push the lighting control stalk down (away) from steering wheel to switch ON the head lamp high beam or lift/pull the lighting control stalk up towards the steering wheel to switch ON the head lamp low beam. In head lamp high beam, the high beam telltale lamp in the instrument cluster illuminates indicating high beam option selected.

8.6.10 Head Lamp Flash

Pull the lighting control stalk (from the head lamp low beam position) towards the steering wheel to instantaneously flash the head lamp high beam. The head lamp flash works only when the head lamp is OFF or in low beam position.

8.6.11 Head Lamp Levelling System

When the vehicle is either fully or partially loaded, it may have an upward inclination disturbing the head lamp aiming. A correct head lamp setting provides good visibility to the driver with minimum inconvenience to other road users.

To properly aim the head lamp beam, use the head lamp leveling switch. This switch is located on the right side of the steering column shroud in the instrument panel. This switch has four positions marked as 0, 1, 2 & 3.

Select the suitable switch position depending on the pay load as advised in the table.

The headlights can only be adjusted when the low beam is switched ON

8.6.12 Hazard Warning Lamp

The hazard warning lamp switch is located in the centre bezel switch bank on the instrument panel.

To turn the hazard warning lamp ON, push the switch in. All the turn signal lamps flash. The instrument cluster turn indicator lamps also flash indicating the same. To turn OFF, push the switch again.

Use the hazard warning lamp when your vehicle is stationary or to warn other road users to be cautious while passing your vehicle.

The turn lamps do not work when the hazard warning lamps are operational.

8.7 Windshield Wipers

8.7.1 Wiper Control Stalk

8.7.2 Wiper Off

The wipe function is OFF when the wiper control stalk is in neutral position (B).

8.7.3 Flick-Wipe (Mist)

Push the wipe control stalk to position (A) for a flick-wipe, hold to operate the wipe continuously (simultaneously lift the wiper stalk towards the steering wheel to operate the wash). The stalk automatically comes back to position (B) when released.

8.7.4 Intermittent (INT) Mode

Intermittent (INT) wiping is selected when the wipe control stalk is pushed down to position C. In the INT mode, the wiper operates on preset intervals.

The delay between each wipe can be varied by rotating the wiper speed intensity rotary switch (F).

8.7.5 Low Speed Wiping

Push the wipe control stalk down to the position (D) to operate the wiper at a fixed low speed.

8.7.6 High Speed Wiping

Push the wiper control stalk down to position (E) to operate the wiper at a fixed high speed.

The wipe/wash function can be activated only when the ignition is in “ON” position.

8.7.7 Wipe/Wash

Pull/Lift the wiper control stalk towards the steering wheel from any position to activate wipe/wash function. Washer fluid from front washer reservoir is pumped and sprayed onto the windshield. The wipers wipe the windshield 3 times after the washer spray is stopped and wipe once after 5 sec. Hold the stalk in position for continuous spray of washer fluid.

When wiper is in OFF or Interval mode:

After completion of the wipe/wash cycle, wipers return to their bottom position.

If the wipers are in interval mode and DWELL delay is less than or equal to 5 seconds, then the wiper will continue in the interval mode.

If the wipers are in interval mode, and DWELL delay is more than 5 seconds, then a further single wipe will be performed 5 seconds after the wash/wipe cycle. After the drip wipe (last wipe), wiper returns to normal interval wipe.

8.7.8 Rear Wiper

Rotate the outer rotary switch on the wiper control stalk to align the “arrow” on the stalk to the rear wipe “ON” position to operate the rear wiper.

8.7.9 Rear Wash

The rear windshield wash & wipe operates 3 to 4 times or as long as the stalk end is turned/rotated to the rear wash position. Wiping will continue for few seconds after releasing the stalk end switch.

If you switch OFF the ignition before switching OFF the wiper, the blades stop at random on the windshield. Switch ON the ignition and move wiper stalk to 'MIST' position to return the wipers to the park position, provided the wiper stalk is in OFF position.

Using a windshield washer in freezing temperatures could be dangerous. The washer fluid could freeze on the windshield, and block your vision resulting in an accident. If you operate your vehicle in temperatures below 4°C, use washer fluid with antifreeze protection.

• Do not operate the wipers when the windshield is dry. It may lead to scratches on the glass
• It is recommended not to use the wiper when the windshield glass is covered with debris, snow or leaves. Clean the glass before using the wiper to avoid damage to the wiper blades and glass
• Do not operate the windshield washer for more than 10 seconds or when the reservoir is empty.

With the front wipers ON and rear wipers OFF, engaging the reverse gear activates the rear wiper.

There are two nozzles with three adjustable washer jets in the front (below the wipers). Using a pin, the eye ball jets can be adjusted precisely for direction. Always direct the washer jet to hit middle of the windshield. This will enable the wiper blade to wipe the complete width of the windshield.

In the rear, two nozzles with twin adjustable washer jets are provided for the rear windshield wash. Adjust the nozzle to direct the washer jet to hit the middle of rear windshield using a pin. Rear windshield washer fluid is supplied from rear washer reservoir located in the back door.

8.8 Instrument Cluster

The instrument cluster comprises of the tachometer, speedometer, trip meter (A & B), Reset Button, Odometer, Fuel gauge, Coolant Temperature gauge, Warning lamps and Telltale indicators.

8.8.1 Tachometer

The tachometer indicates the real time engine speed in thousands of RPM (revolutions per minute). Each division is 500 RPM. Running the engine in very high RPM leads to excessive engine wear and poor fuel economy. Maintain steady engine speed below 2500 RPM and do not accelerate or decelerate abruptly.

Do not over-accelerate the engine during idling, this can cause severe engine damage and would be treated as abuse of the engine which is not covered by warranty.

8.8.2 Speedometer

The speedometer indicates the real time road surface speed of the vehicle in kilometers per hour.

The vehicle speedometer is affected by size of the tires used. If the size of the tires are changed from those fitted at the factory, the speedometer might not display the correct road surface speed and distance travelled.

8.8.3 Odometer

The odometer records and displays the total distance traveled in kms. Press the reset button (A) to cycle through odometer and tripmeter displays. Odometer cannot be reset.

8.8.4 Tripmeter and Reset Button

Tripmeter displays the elapsed distance travelled since the last trip reset. There are two tripmeter’s (A/B) which can be reset individually as necessary.

Odometer and Tripmeter are displayed only when the ignition is ON and their displays are cycled/toggled by the reset button (A).

• To select trip A or B, press and release reset button (A) for a second
• To shift from trip A to trip B or vice versa, press and release the reset button (A) again for a second
• While on trip A or B, press and hold the reset button (A) for more than 1 second to reset the respective trip reading to zero\
• Pressing the reset button (A) while in trip B, displays the odometer reading. Again pressing the rest button (A) displays trip A

The engine coolant temperature gauge functions only when the ignition is switched ON. It indicates the instantaneous engine coolant temperature. The coolant temperature varies with changes in weather, load on engine and driving pattern. Temperature rises from Cold (C) (Blue color) to Hot (H) (Red Color).

When coolant temperature reaches the red zone, the high engine coolant temperature warning lamp illuminates.

In such situations switch OFF the AC and observe for any improvements in temperature gauge. If not, stop the vehicle and allow the engine to cool down. Check the coolant level in the coolant reservoir and top-up if required. If the engine is still heating up, contact your nearest Authorized Mahindra Dealer.

Never remove the radiator cap when the engine is hot. The engine coolant is under pressure and could splash on to skin/eyes causing severe burns. Wait for the engine to cool down before adding coolant to the reservoir.

Do not continue driving the vehicle with a overheated engine. This will lead to damage of engine components and engine seizure.

8.8.6 Fuel Level Gauge

The fuel level gauge functions only when the ignition is switched ON. It gives the status of the fuel level in the fuel tank. F indicates the tank is full (70 liters), E indicates the tank in empty.

When the fuel level reaches the reserve, the last 2 bars are displayed. The last bar in the display blinks when the fuel in the tank reaches the low level (approx. 5 liters).

The amount of fuel required to fill the tank up may be less than the specified tank capacity, as a small amount of reserve fuel always remains in the tank.

On inclines or curves, due to the movement of fuel in the tank, the fuel level may fluctuate or the last bar may flash earlier than usual. Always check the fuel level when the vehicle is on level road.

When all the bars in the display starts blinking/ flashing, contact the nearest Authorized Mahindra Dealer at the earliest.

The direction of the arrow next to the fuel pump icon in the fuel gauge indicates the side on which the fuel lid is present.

8.12 Warning/Telltale Lamps in the Instrument Cluster

8.9.1 Seat Belt Warning Lamp

The seat belt warning lamp illuminates reminding the driver to fasten the seat belt when the ignition is ON. The lamp will continue to illuminate till the driver fastens the seat belt properly.

8.9.2 Turn Lamps

The turn lamp arrows in the instrument cluster flash showing the direction indicated by the turn signals. A sudden increase in the rate of flashing indicates failure of one or more of the lamp bulbs. Have them replaced as soon as possible.

8.9.3 Airbag Warning Lamp

The airbag warning lamp in the instrument cluster illuminates when the ignition is switched ON and goes OFF in about 2 seconds once the engine is running. If the lamp remains ON continuously or flash’s intermittently, contact an authorized Mahindra dealer immediately.

Following conditions indicate airbag malfunction:

• Lamp fails to go OFF after engine is started
• Lamp does not illuminate at all
• Illuminates while driving

Contact an authorized Mahindra dealer immediately when the airbag warning lamp indicates a system malfunction. The airbag may not deploy when needed, which could result in serious or fatal injury, or it might deploy unexpectedly or unnecessarily, which may result in personal injury.

8.9.4 Low Fuel Warning Lamp

8.12.4 Glow Plug Indicator

8.9.6 Vehicle Armed Status Lamp

Fast blinking indicates a malfunction in the engine immobilizer system. Contact an Authorized Mahindra Dealer immediately.

8.9.7 High Engine Coolant Temperature Warning Lamp

Do not continue driving the vehicle with an overheated engine. This may result in engine damage, which will not be covered by the limited warranty.

8.9.8 Water-in-Fuel Warning Lamp

8.9.9 Low Engine Oil Pressure Warning Lamp

Operating the vehicle with the low oil pressure warning lamp ON could cause sudden unexpected engine failure and loss of vehicle control, resulting in an accident and/or serious personal injury.

Do not run the engine with low oil pressure warning indicator ON. This may result in engine damage, which will not be covered by the limited warranty.

8.9.10 Check Engine Lamp

The check engine lamp illuminates when the ignition is switched ON and goes out in 2 seconds indicating normal status. The lamp blinks or illuminates continuously if there is a fault in the engine management system. Switch OFF the engine immediately. Contact the nearest Mahindra dealer for necessary repairs.

8.9.11 Parking Brake Lamp

The lamp illuminates when; Parking brake is engaged or when brake fluid level is low or when front brake pads are worn. If the lamp illuminates while driving, do the following:

• Check if the parking brake is engaged. If yes, disengage it
• Check if brake fluid level is low. If yes, top-up brake fluid to the required level
• If the brake lamp still continues to illuminate, immediately get the vehicle checked at an Authorized Mahindra Dealer.

Clean the top of the brake fluid reservoir before removing the cap. Make sure no dirt, impurities or other items fall into the reservoir. Do not leave the cap off for more than a few minutes. Any contaminants, impurities or moisture in the brake fluid can affect brake operation, resulting in an accident.

If the brake warning lamp comes ON while driving, the brake system might not be working properly. The pedal might be harder to operate or might go closer to the floor and it can take longer to stop. Pull off the road carefully and stop the vehicle. Have the vehicle towed to the nearest Authorized Mahindra Dealer for checks or repairs.

Driving the vehicle with the brake warning lamp ON or when you suspect brake trouble is very dangerous and could result in serious injuries. Have your vehicle towed to an Authorized Mahindra Dealer.

8.9.12 OBD Check Lamp

The OBD check lamp illuminates when the ignition is switched ON and remains ON till the engine is started indicating normal status. If the lamp remains ON, it indicates a potential malfunction.

There may be a malfunction in:

• The fuel management system
• The emission control system
• Systems which affect emissions

Such malfunctions may result in excessive emissions. Contact an Authorized Mahindra Dealer immediately.

8.9.13 Head Lamp High Beam Lamp

The head lamp high beam telltale illuminates whenever the head lamps are switched ON to high beam or when the head lamp flash is used.

8.9.14 Stop/Start Lamp

The Stop/Start - Stop/Start lamp flashes when the vehicle/engine is about to stop through the Stop/ Start System. The lamp illuminates continuously when the vehicle/engine has been switched OFF by the Stop/Start System. On restarting the vehicle/ engine again by using the clutch/key, the lamp goes out.

8.9.15 Anti-lock Brake System (ABS) Malfunction Lamp (if equipped)

The ABS malfunction lamp illuminates when the ignition is switched ON and goes OFF after about 2 seconds. If the ABS malfunction lamp continues to remain ON or illuminates while driving (and the brake system warning lamp is OFF), ABS will not operate. But the brake system will still operate conventionally. In this condition, the wheels can lock during severe braking. Have the vehicle checked by an authorized Mahindra dealer as soon as possible.

However, if ABS malfunction lamp and brake warning lamp are simultaneously glowing, there is a severe malfunction in the ABS. Operate the vehicle with extreme care and have the vehicle checked as soon as possible at an authorized Mahindra dealer.

8.9.16 Battery Charging System Warning Lamp

The battery charging system warning lamp illuminates when the battery is not being charged or when there is a malfunction in the alternator.

This lamp illuminates when the ignition is switched ON and goes out as soon as the engine is started. If the lamp continues to remain ON even after starting the engine, it is an indication that the battery is not being charged or there is a malfunction in the alternator. Check the alternator drive belt for looseness/breakage. If the drive belt is okay, switch OFF all unnecessary electrical equipment and recheck. Contact an Authorized Mahindra Dealer for further assistance.

8.9.17 Door Ajar Warning Lamp

The door ajar warning lamp illuminates and the buzzer chimes 3 times when any of the doors including the hood and back door are open during ignition ON. The lamp goes OFF when all the doors are closed properly.

9 STEERING AND BRAKES

9.1 Steering

Your vehicle is equipped with power steering. Power steering uses energy from the engine to decrease the driver's effort in steering the vehicle. The power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. If for some reason the power assist is interrupted, it will provide mechanical steering capability to steer the vehicle. Under these conditions, you will observe a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.

Upon initial start-up in cold weather, the power steering pump may produce noise for a short amount of time. This is due to the cold, thick fluid in the steering system. This noise should be considered normal, and it does not in any way damage the steering system.

Continued operation with reduced power steering performance could pose a safety risk to yourself and others. Have the vehicle serviced at specified intervals or whenever a power steering problem is noticed.

Do not grip the steering wheel spokes when driving off road. A bad bump could jerk the wheel and injure your hands. Keep both hands especially your thumbs on the outside of the steering wheel rim.

• Never hold the steering wheel to the extreme right or the extreme left for more than a few seconds when the engine is running
• Heavy or uneven steering efforts may be caused by low power steering pump fluid level. Check for low power steering pump fluid level before seeking service by an Authorized Mahindra Dealer
• Do not fill the power steering pump reservoir above the MAX mark on the reservoir, this may result in leaks from the reservoir

If the power steering system breaks down (or if the engine is turned OFF), you can still steer the vehicle manually, but it takes more effort.

• Under inflated tire(s) on any wheel(s)
• Uneven vehicle loading
• High crown in the centre of the road
• High crosswinds
• Wheels out of alignment
• Wheels out of balance
• Loose or worn suspension components

9.1.1 Tilt Steering

The steering wheel can be adjusted for both rake and reach as required using the lever in the steering shroud under the steering wheel.

To tilt/adjust the steering wheel;

1. Pull the tilt lever down to unlock.

2. Raise or lower the steering wheel to the desired position.
3. Pull or push the steering wheel to the desired position.
4. Push the tilt lever back up to its original position to lock the steering.

improperly locked steering wheel could cause loss of control and lead to accidents. Never adjust the steering wheel while driving.

9.2 Brakes

Your vehicle is equipped with disc brakes in the front and drum brakes in the rear.

Disc brakes offer good braking capability and reduced stopping distance. Wet brake discs result in reduced braking efficiency. After a car wash or driving the vehicle through water, dab the brake pedal while driving to remove the film of water from the brake pads. Brake pads feature wear indicator. When the brake pad is worn, metallic squeal noise is heard indicating the pad wear. Have them replaced immediately.

Driving with wet brakes is dangerous. Stopping distance increases considerably when braking.

Dry the brakes by driving at very slow speed and applying the brakes lightly until the brake performance becomes normal.

Even if the power assist (vacuum assistance) is completely lost, the brakes will still work. The brake pedal would be much harder than normal and the vehicle stopping / braking distance will be longer than usual.

9.2.1 Parking on a Hill/Incline

If you have to park facing uphill, select first gear and turn the front wheels away from the kerb. If you have to park facing downhill, select reverse gear and turn the front wheels towards the kerb. Always ensure the vehicle is in gear and parking brakes is engaged before leaving the vehicle.

9.2.2 Parking Brake

To apply the parking brake, pull the park brake lever up as firmly as possible. When the parking brake is applied with the ignition ON, the brake warning lamp in the instrument cluster illuminates. To release the parking brake, pull the parking brake lever up slightly, press the release button on the lever tip and lower the parking brake lever completely.

The brake warning lamp indicates only the parking brake status. It does not indicate the degree of brake application. Be sure the parking brake is firmly set when parked and the gear shift lever is in gear. When parking on a hill you should apply the parking brake before placing the shift lever gear, since the load on the transmission locking mechanism may make it difficult to move the shift lever out of gear.

Be sure the parking brake is fully disengaged before driving off. Failure to do so can lead to brake problems due to excessive heating of the rear brakes.

• The parking brake should be adjusted as per recommended maintenance schedule
• Always apply the parking brake when leaving the vehicle, and be certain to leave the transmission in gear. Failure to do so may allow the vehicle to roll and cause damage, hit a bystander resulting in personal injury.
• Leaving unattended children in a vehicle is dangerous for a number of reasons. Children should be warned not to touch the parking brake or the gear shift lever. Do not leave the key in the ignition. A child could move the vehicle leading to accidents
• The parking brake should always be applied when the driver is not in the vehicle.

Engaging the parking brake while the vehicle is in motion can cause the rear wheels to lock up. You could lose control of the vehicle and cause an accident.

9.3 Anti-Lock Brake System (ABS) (if equipped)

The Anti-lock Brake System (also called as ABS) is designed to help prevent lock-up of the wheels and stable stopping of vehicle during a sudden, panic emergency braking or braking on slippery road surfaces. The ABS system takes input from wheel speed sensors and brake pedal switch to control the brake fluid pressures at the wheels to avoid wheel lock-up. It allows vehicle to be steered during braking.

The minimum speed for ABS to function is 12 kmph. ABS is activated only during wheel lock conditions where ABS takes over and prevents wheel lock.

During the ABS operation, a slight pulsation may be felt in the brake pedal to indicate ABS is active. You may also hear motor noise from the engine compartment. It is recommended to hold the brake pedal firmly while the ABS is active rather than pumping the brake pedal.

Depressing the brake pedal on slippery road surfaces as on a manhole cover, a steel plate at a construction site, a joint in a bridge, etc. on a rainy day, tends to activate the anti-lock brake system.

The ABS warning lamp lights up when you switch ON the ignition and should go out after a few seconds. If the ABS warning lamp does not go out or if it comes ON while driving, it means there is a fault in the ABS system. In both cases, the normal braking system remains efficient, exactly as on a vehicle without ABS. The vehicle should be examined as soon as possible by an authorized Mahindra dealer.

The Anti-lock brake system is not designed to shorten the stopping distance: Always drive at a moderate speed and maintain a safe distance from the vehicle in front of you. The stopping distance may be longer in the following cases:

• Driving on rough, gravel or snow covered roads.
• Driving with tyre chains installed.
• Driving over the steps such as the joints on the road.
• Driving on roads where the road surface is pitted or differences in surface height.

Do not overestimate the Anti-lock Brake System: Although the Anti-lock Brake System assists in providing vehicle control, it is still important to drive with all due care and maintain a moderate speed and safe distance from the vehicle in front of you. There are limits to the vehicle stability and effectiveness of steering wheel operation even with ABS active.
If tyre grip performance exceeds its capability, or if hydroplaning occurs during high speed driving in the rain, the Anti-lock Brake System will not assist with vehicle control.

9.4 Electronic Brake Force Distribution (EBD) (if equipped)

EBD, as a subsystem of the ABS system, controls the effective adhesion utilization of the rear wheels. EBD aids in distributing the brake forces more evenly leading to better vehicle stability during braking.

Typically, the front end carries more weight and EBD distributes less braking pressure to the rear brakes avoiding a lock up/skid.

For example, under light loads EBD applies less effort to the rear brakes and for heavy loads it allows full braking effort to the rear wheels.

A fault with EBD is indicated by illumination of the brake as well as ABS warning lamps. The vehicle should be examined as soon as possible by an authorized Mahindra dealer.

9.5 Hydraulic Brake Assist (HBA) (if equipped)

ESP system recognizes / identifies an emergency braking situation from the braking characteristics and thereby achieves a braking output equivalent to a full force demand at the controls. HBA automatically boosts the braking force to the maximum and helps to stop the vehicle as quickly as possible.

Pressure should be maintained on the brake pedal during entire brake application. If the brake pedal is released, HBA will stop operating

10 HEATING, VENTILATION AND AIR-CONDITIONING SYSTEM (HVAC)

HVAC system provided in the vehicle enables occupants to automatically/manually adjust air flow distribution pattern, air flow rate, air intake mode and air temperature inside passenger compartment. By appropriately adjusting the control knobs/switches provided on the HVAC control panel, located on centre console, occupant’s comfort can be ensured. HVAC system also helps in defrosting and defogging/ de-misting the windshield and windows.

Air flow direction can be further controlled by adjusting louvers of air vents. An air filter is provided at the inlet of HVAC blower.

Engine coolant is utilized to heat the cabin air. For cooling the cabin air, an air conditioning circuit based on the vapor compression refrigeration cycle is used. The air conditioning system uses a refrigerant along with a suitable lubricating oil. Although being non-ozone depleting, the refrigerant is a greenhouse gas, hence once allowed to escape in the atmosphere, it adversely affects the environment by contributing to global warming/climate change.

Refrigerant used in system is a hazardous liquefied gas and is under high pressure. The refrigerant is colorless and has ethereal or faint sweetish odor. Exposure of refrigerant to skin or eyes may cause irritation and frostbite. They can also cause suffocation, dizziness and loss of concentration. When mixed with compressed air or certain other refrigerants, it may form flammable mixture. Never try to service HVAC system yourself which would involve refrigerant handling.

Multiple vents are provided for distributing the air, being force-circulated by HVAC blower, throughout the passenger compartment.

To ensure sufficient air flow and hence adequate HVAC system performance, air flow path should be kept free of obstructions. Keep system’s air intake, located near plenum appliqué, free of snow, leaves and other debris. Also keep the area in front of air vents free of any obstruction inside the cabin.

10.1 HVAC Overview

10.1.1 Centre/Side Vents

Two centre vents are located on either side of the infotainment screen in the centre console. The two side vents are located one each at the left and right extreme ends of the instrument panel. Both the centre and side vents provide air flow to the front seat passengers.

Rotate the thumb wheel (B) left to close or right to open the air vent. Direct air to the desired direction by the adjusting louvers (A) up/down or left/right.

10.1.2 Defrost Vents - Side/Windshield

There are four defrost vents in your vehicle; two side defrost and two windshield defrost vents. They are located just below the windshield. The side defrost vents prevent the front windows from de-misting, whereas the windshield A Adjustable Louvers B Thumb Wheel defrost vents help in clearing the mist from windshield.

10.1.3 Second/Third Row Roof Vents

Two (LH & RH) vents for the second row are provided on the B-Pillars. The vents have adjustable louvers to direct the air flow and thumb wheels for vents open/close operations.

The third row vents (LH & RH) are located on side trims on either side of the third row seats.

10.2 Climate Control

There are two types of climate control depending on the variant ;

10.3 Temperature Control

By operating the temperature control knob, temperature of air being discharged from various vents can be adjusted to the desired level. Engine coolant is utilized to heat whereas the air conditioner is used to cool the air inside the AC unit. Based upon selected position of the temperature control dial, the desired discharged air temperature can be obtained.

By rotating the dial counter-clockwise and setting it to the extreme left position, cool air is discharged.

When the dial is rotated clockwise, the discharge air progressively starts getting warmer.

By rotating the dial further in the clockwise direction and setting it to the extreme right position, hot air is discharged.

10.4 Blower Speed Control

Blower force-circulates air through the HVAC unit and distributes it throughout the passenger compartment.

To increase the blower speed, rotate the control dial clockwise (B) and to reduce the blower speed, rotate the dial counter clockwise (A).

To switch OFF the blower, rotate the dial to “0”.

A blower control is provided below the third row (RH) vent to control the air flow to the third row vents.

The third row AC is switched ON by the Rear AC button on the central switch bank. The airflow is controlled by the blower control on the third row RH side trim.

10.5 Economy Button (ECon)

ECON switch turns ON economy mode. During ECON AC operation the system automatically cuts OFF at a higher temperature than normal AC. The operation can be used during mild weather conditions for better fuel efficiency. Comfort level may be compromised during this operation.

LED on the button indicates the status of the button. Press the ECON switch again to turn OFF economy mode.

10.6 Air-conditioner ON (AC ON)

This button turns the air-conditioner ON or OFF. Adjust the temperature control dial as per the temperature requirement. LED on the button indicates the status. Push the button to turn ON/OFF the AC.

When the air conditioner is functioning, air gets cooled and de-humidified before being circulated inside the cabin. In hot weather conditions, it will take a slightly longer time to cool the interior as compared to cooler weather. Fuel consumption will be relatively higher if the vehicle is being driven with the air conditioner ON.

AC will function only when both engine and blower are switched ON.

• In certain operating conditions when the engine gets overheated, the engine management system may switch off the air conditioner intermittently.
• The air conditioner should be operated at least for ten minutes once every fortnight, even during winter months. This allows AC system components to get lubricated periodically and ensures optimum system
• During extreme cold weather conditions, the air conditioner may not function until temperature of the air near the evaporator rises above a predefined threshold.
• When air conditioner is ON, moisture is extracted from the air. The resulting condensate is drained off from the vehicle. It is therefore normal, if you see a small pool of water under your vehicle.

10.7 Re-circulation Mode

To set the HVAC system to recirculation mode, press the recirculation mode button. The LED on the button illuminates, indicating the recirculation mode is active.

In this intake mode, the air from inside the passenger compartment will be sucked by the blower and utilized further to ventilate/cool/heat the cabin.

For quick cabin cooling/heating or while driving through dusty/polluted region, re-circulation mode can be selected for short periods. Driving with this mode active may lead to better fuel economy and longer HVAC filter life.

However, running the air conditioner in re-circulation mode for long will make cabin air too dry and oxygen level drops inside cabin turning the air stale. On the contrary, keeping air intake control in recirculation mode for long, with air conditioner switched OFF, will make cabin air too humid and are more likely to become foggy. Hence never drive in recirculation mode for long, shift back to fresh air mode as soon as possible.

Never keep recirculation mode selected continuously for long. Prolonged use of the HVAC system in recirculation mode may cause windshield/windows to mist/fog-up, impairing visibility which can lead to an accident, endangering you and others.

10.8 Fresh Air Mode

To set the HVAC system to fresh air mode, press the re-circulation mode button again. The LED on this button switches OFF, indicating that re-circulation mode is active.

10.9 Rear AC

The rear AC provides cooling for the third row AC vents. Adjust the temperature control dial as per the temperature requirement. LED on the button indicates the status.

The rear AC can be switched ON only when the AC button (front/second row AC) is ON.

10.10 Air Distribution Mode

Air distribution mode allows you to select the below air flow patterns;

• Face Mode — Air is discharged through the centre and side vents on the instrument panel, and through the second row B-pillar vents
• Face and Floor Mode — Air is discharged through the centre, side and foot vents on the instrument panel, and through the second row B-pillar vents
• Floor Mode — Air is discharged through the foot/floor vents on the instrument panel
• Floor Defrost Mode — Air is discharged through the foot/floor vents, windshield vents and side defrost vents on the instrument panel.

Press the required mode button on the switch bank.

10.11 Rapid Cabin Cooling

1. Make sure that all the windows are fully closed
2. Set the blower to maximum speed
3. Fully open the vents and adjust louvers to direct air toward face
4. Set the air distribution control to face mode
5. Set air intake control to fresh air mode
6. Turn the air conditioner ON
7. Set the temperature control dial to extreme left (coolest) position

For faster cabin cooling you can select re-circulated air intake mode initially. Once passenger compartment reaches a comfortable temperature, shift to fresh air mode. Also blower speed and temperature control knob can be re-adjusted as desired.

If your vehicle was parked in the hot sun with all the windows closed, drive the vehicle with windows open for the first few minutes. This will help in venting the hot interior air out and allow the air conditioner to cool the cabin quickly.

10.12 Rapid Cabin Heating

1. Make sure that all the windows are fully closed
2. Set the blower to maximum speed
3. Set the air distribution control to foot mode
4. Set air intake control to fresh air mode
5. Set the temperature control dial to extreme right (hot) position
6. For de-humidified heating, switch the air conditioner ON

For faster cabin heating you can select re-circulated air intake mode initially. Once passenger compartment reaches a comfortable temperature, blower speed and temperature control knob can be re-adjusted as desired.

In extreme cold weather conditions, the engine coolant takes time to get heated up. Hence it might take a while for hot air discharge, even when blower is running and temperature control dial is set to hot position.

10.13 Front Windshield Defogging/De-misting

Front windshield glass defogger switch is located on the blower speed control dial in the central switch bank. Press the switch once to activate the defogger. The lamp on the switch illuminates upon activation. AC is turned ON, air is discharged through the windshield defroster vents, side defroster vents and side vents. Air intake mode is switched to fresh air mode automatically. The defogger heats the front windshield clearing the fog/ frost.

Switch OFF the defogger by pressing the switch again as soon as the fog/frost is cleared.

If the windshield defogger switch is not switched OFF manually, it will turn OFF automatically after a pre-defined time, based on ambient temperature.

If you want to switch the defogger ON again, press the defogger switch again.

On second and subsequent activations of the rear windshield defogger in the same ignition cycle, the defogger ON time will be half the duration of the first activation.

10.14 Rear Windshield Defogging/De-misting

Rear windshield glass defogger switch is located on the temperature control dial in the central switch bank. Press the switch once to activate the defogger. The lamp on the switch illuminates upon activation and the defogger heats the rear windshield clearing the fog/ frost.

Switch OFF the defogger by pressing the switch once as soon as the fog/frost is cleared.

If the windshield defogger switch is not switched OFF manually, it will turn OFF automatically after a pre-defined time, based on ambient temperature.

If you want to switch the defogger ON again, press the defogger switch again.

On second and subsequent activations of the rear windshield defogger in the same ignition cycle, the defogger ON time will be half the duration of the first activation.

10.15 Points to Remember

• For quickly defogging/de-misting/defrosting outside of windshield, it is advisable to operate the windshield wiper/washer for few times intermittently.
• If snow has deposited on windshield, use ice scraper to remove ice deposited before using wiper.
• In freezing weather, warm the windshield with the defroster before using the windshield washer. Also use a washer fluid having anti-freezing properties. These will help prevent the washer fluid from freezing on your windshield.
• Dirty/contaminated windshield would make misting/ fogging-up worse. Always keep the inside and outside of windshield clean.
• Reduced air flow because of clogged HVAC filter or any other obstructions in air flow path may lead to in-adequate defogging/de-misting/defrosting performance. If air flow seems to have considerably reduced, get the filter cleaned or replaced immediately. Air flow path should be kept free of obstructions.
• Reduced cooling performance from air conditioner may lead to in-adequate defogging/de-misting/defrosting. If cooling effect seems to have dropped considerably, get the air conditioning system checked by an authorized Mahindra dealer.

Your vehicle is equipped with a HVAC filter. If the AC performance is considerably low, it is recommended have the HVAC filter checked at the nearest Mahindra dealer.

Never operate HVAC system with the filter removed. This may result in premature failure of system components.

11 STARTING AND DRIVING THE VEHICLE

11.1 Safety Tips - Before Starting your Vehicle

11.1.1 General

• Before starting the vehicle, inspect the inside and outside of the vehicle and look for any damages, leaks, loose parts, foreign objects/debris. Contact an Authorized Mahindra Dealer if required.
• Before starting your journey, check the working of all safety devices/components especially brakes, steering, lamps, signals and tires. In case you suspect any system/devices not working properly contact Authorized Mahindra Dealer.
• Adjust the seat headrest, steering wheel and fasten the seat belt as described in this manual. Never perform any seat/ steering adjustments when the vehicle is in motion.
• Start the vehicle only when seated and belted in the driver's seat.

The Engine Management System controls the engine's idle speed. When the engine starts, idle RPM runs higher than normal in order to warm the engine. The engine idle speed RPM reduces once the engine warms up.

Never start your vehicle in a closed garage or in an enclosed area. Exhaust fumes can be toxic. Always keep the garage door open or start the engine in an open area.

Ensure that the rear view mirror and both the ORVM’s are adjusted for an unobstructed view of the road behind.

Have someone observe and confirm normal operation of all exterior lamps while you work on the controls from the driver seat. Also, check functioning of all lamps in the instrument panel.

Check for positive closing, latching, and locking of all doors, both from inside and outside.

Check the area under vehicle after an overnight parking for fuel, power steering fluid, brake fluid, engine coolant, oil, or other fluid leaks. If leaks are observed, contact an Authorized Mahindra Dealer.

Make sure all vehicle occupants are properly seated in their seats and have buckled their safety belts. For more information on seat, headrest positioning, safety belts and their proper usage, refer to the “Seat Belts” section in this manual.

• Make sure the gear shift lever is in neutral
• Make sure the parking brake is engaged. Turn the key to IGN position but do not turn the key to start
• Few warning lamps briefly illuminate. See “Warning Lamps in the Instrument Cluster” section for more information

1. Shift the gear shift lever to neutral position.
2. Apply parking brake.
3. Turn the ignition ON.
4. Do not press the accelerator.
5. Turn the key momentarily to the START position to crank the
6. Once the engine starts, release the key; it will return to the IGN position
CAUTION

Do not continue cranking after the engine has started. This will lead to damage of the starter and other engine components.

7. If the engine fails to start, attempt to restart after about 10
8. If the engine fails to start even after repeated attempts as per the procedure given above, contact the nearest Authorized Mahindra Dealer
CAUTION
9. To prevent damage to the starter, wait 10 seconds before attempting to restart the engine.
WARNING
10. If the vehicle battery has discharged, use booster cables, a booster battery or a battery from another vehicle to start. Jump-starting a vehicle can be dangerous if done improperly. Refer to the “Jump-starting procedure” section in this manual.
11. If the engine still fails to start, contact an Authorized Mahindra Dealer for assistance.
12. The idle speed is controlled automatically and it will decrease as the engine warms up.
Observe the following when the engine is running;
• All warning lamps are OFF
• Low oil pressure lamp is OFF

After idling for a few seconds, release the parking brake, depress the clutch, shift the gear shift lever to 1st gear, release the service brake pedal, drive by releasing the clutch and depressing the accelerator pedal simultaneously.

11.2.1 Engine Idling - In Cold Weather

Avoid full throttle operation when the engine is cold and prolonged idling at low ambient temperatures. Long periods of idling may be harmful to your engine. Combustion chamber temperatures can drop so low that the fuel may not burn completely. Incomplete combustion allows carbon and varnish to form on piston rings and injector nozzles. Also, the unburned fuel can enter the crankcase, diluting the oil and causing rapid wear to the engine.

Your vehicle is powered by a turbo diesel engine. Before turning the engine OFF, always allow the engine to return to normal idle speed and run for few seconds. This assures proper cooling and lubrication of the turbocharger. This is particularly necessary after any hard driving.

To reduce the risk of personal injury, before turning OFF the engine and leaving the vehicle, always,

• Keep your right foot on the service brake pedal
• Turn front wheels towards the road curb
• Switch OFF the ignition, turn the key to the steering lock position and remove the key
• Firmly engage the parking brake
• Move the gear shift lever to 1st gear position (reverse gear if parking on an incline)
• Slowly release the service brake pedal
• Lock your vehicle when leaving

11.4 Exhaust Gases

Protection against exhaust gas entry into the vehicles interior is considered in the design of the exhaust system.

• Vehicle exhaust contains Carbon Monoxide, Carbon Dioxide, Nitrogen Oxides, Hydrocarbons and Particulate Matter. These are potential environmental and health hazards.
• Avoid inhaling the exhaust gases. Carbon Monoxide is a colorless and odorless gas and can cause unconsciousness or even death.
• If the exhaust system is damaged for any reason or you notice a change in the exhaust noise, have the vehicle checked by an Authorized Mahindra Dealer immediately.
• Do not start the vehicle in a closed garage or in an enclosed area where ventilation is poor for the exhaust gases.
• Since the engine compartment and exhaust system components are hot and can ignite a fire, do not park or leave the vehicle with the engine idling over dry grass, leaves, paper, rags or any combustible material.
WARNING

Never keep the engine running when the vehicle is parked in an area which is not properly ventilated. This could lead to serious respiratory problems and/or death.

11.5 Driving Your Vehicle

Always observe the following precautions to minimize the risk of accidents leading to serious personal injury or damage to your vehicle

• Before you drive your vehicle, please read this manual carefully.
• When you start driving, verify proper operation of the brakes and steering system.
• If, while driving, you hear any strange noise or feel unusual vibration, or if you have any concerns whatsoever, or if any warning lamps illuminate or buzzers sound, park/stop the vehicle in a safe location as soon as possible. Identify the cause and take any necessary remedial action. Contact your Authorized Mahindra Dealer if necessary.
• Never overload or improperly load your vehicle.
• Always be attentive while driving and follow safe driving practices.
• Always maintain the recommended inflation pressure in tires.
• Always drive at a safe speed appropriate for given driving conditions. You must follow the speed limits.
• While backing up, keep a constant lookout for people, particularly children, or other obstructions or hazardous material that might be present behind the vehicle.
• Avoid loading any items on the roof that will raise the vehicles center of gravity and make your vehicle more unstable.
• Loaded vehicles, with a higher center of gravity, may handle differently than unloaded vehicles. Extra precautions, such as slower speeds and increased stopping distance, should be taken when driving a heavily loaded vehicle.
• Always slow down in gusty crosswinds. Because of its profile and higher center of gravity, your vehicle is more sensitive to side winds than an ordinary passenger car. Slowing down will allow you to have much better control. s
• When driving off-road or on rugged terrain, do not drive at excessive speeds, jump, make sharp turns, strike objects, etc. This may cause loss of control or vehicle rollover causing serious injury. You are also risking expensive damage to your vehicle's suspension and chassis.
• Maintain steering wheel control at all times, especially on rough terrains. Sudden changes in terrain can result in abrupt steering wheel motion. Make sure you grip the steering wheel from the outside. Do not grip the spokes.
• If the vehicle goes from one type of surface to another (e.g. from concrete to gravel/sand/mud/snow) there will be a change in the way the vehicle responds, especially the way it responds to steering, braking and accelerating inputs.
• Be extremely careful when driving on pavements made slippery by loose sand, water, gravel, snow or ice.
• If your vehicle goes off the edge of the pavement, slow down, but avoid severe brake or steering application. Ease the vehicle back onto the pavement only after reducing your speed. Do not turn the steering wheel too sharply while returning to the road surface.
• It may be safer to stay on the apron or shoulder of the road and slow down gradually before returning to the pavement. You may lose control if you do not slow down or if you turn the steering wheel too sharply or abruptly.
• In an unavoidable emergency situation where a sudden sharp turn must be made, turn the steering wheel only as rapidly and as far as required to avoid the emergency. Excessive steering will result in less vehicle control. Additionally, smooth variations of the accelerator and/or brake pedal pressure should be utilized if changes in vehicle speed are called for. Avoid abrupt steering, acceleration or braking which could result in an increased risk of loss of vehicle control, vehicle rollover and/or personal injury. Use all available road surfaces to return the vehicle to a safe direction of travel.

11.5.2 Off Road Driving Precautions

• When driving off-road or on rugged terrains, never overspeed or make sharp turns. This may cause loss of control or vehicle rollover causing serious injury.
• Maintain steering wheel control at all times. Sudden changes in terrain can result in abrupt steering wheel motion.
• Do not drive horizontally or diagonally across steep slopes, your vehicle can tip over sideways. Driving straight up or straight down is preferred.
• Drive cautiously to avoid vehicle damage from concealed objects such as rocks and stumps. You should either know the terrain or map-out your route before driving in the area.
• Always perform a maintenance inspection after each day of off-road driving that has taken you through rough terrain, sand, mud or water.

11.5.3 Driving Through Water

Although your vehicle is capable of driving through shallow water, there are a number of precautions that must be considered before entering the water.

Never drive through still water that is higher than the bottom of the axle hubs. Not following this instruction will allow water to enter vehicle components causing internal damage to the components, affecting driveability, safety, emissions and reliability.

When driving through water, drive very slowly and at constant speed, less than 5 kmph. Water waves generated will be high and may enter air intake, causing severe engine damage or cause a vehicle to get stalled.

You must slow down while driving through shallow water. Speeding may cause water to splash onto the windshield, impairing your vision.

• The ground under the water might not be firm which could result the water being deeper than expected when driving the vehicle through it.
• Do not stop or shut OFF the engine while immersed in water. It helps in preventing water getting inside the exhaust pipes.
• When backing down a ramp, do not allow the exhaust tail pipe to immerse in water.
• Water can wash the grease from wheel bearings, causing rusting and premature failure. It may also enter the differentials, transmission and transfer case, reducing the oil's lubricating qualities. If these are submerged in water, the lubricants should be replaced as required.
• Water entering the transmission will cause deterioration in shift quality, locking up of your transmission accompanied by vibration, and ultimately damaging the transmission.
• Sand, mud/sludge that has accumulated in brake drums and around brake discs may affect braking efficiency. This may also damage brake system components. Wet brakes cannot stop the vehicle as effectively as dry brakes. Drying can be improved by driving the vehicle slowly while applying light pressure on the brake pedal.
• When driving through water, traction or brake capability may be limited. Always perform a maintenance inspection after each day of off-road driving that has taken you through water.

If the water is swift flowing and rising (as in storm run-off) avoid crossing until the water level recedes and/or the flow rate is reduced.

The flowing water can erode the streambed causing your vehicle to sink into deeper water.

Determine the exit point(s) that are downstream of your entry point to compensate for drifting.

Off-road operation puts more stress on your vehicle than does most on-road driving. Always perform a maintenance inspection after each day of off-road driving that has taken you through rough terrain, sand, mud, or water.

• After going off-road, it is always a good idea to check for damage. Completely inspect the underbody of the vehicle for any damages.
• Check for accumulations of plants or bushes. These could be a fire hazard. They might also hide damage to fuel lines, brake tubes/hoses, etc.
• Inspect all the tubes/hoses and check for any fluid leakages.
• Get heat exchangers (radiator and condenser) cleaned.
• Check threaded fasteners for looseness, particularly on the chassis, drive train components, steering, suspension and brakes. Retighten them, if required, and torque to the values specified in the ‘Repair Manual’.
WARNING

Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. You might not have full braking power when needed leading to accidents. If you have been operating the vehicle in off-road conditions, get the brakes checked and cleaned as necessary.

• If any unusual vibration is experienced, check the wheels for impacted material. Impacted material can cause a wheel imbalance. Get it inspected/corrected as soon as possible.
• After driving through deep water, inspect your vehicle fluids and lubricants (engine oil, transmission/transfer case/axle oils) to ensure the fluids have not been contaminated.

11.6 Tips for Better Fuel Economy

Give due consideration to the points listed below for better performance of vehicle and enhancement of fuel economy.

Give due consideration to the points listed below for better performance of vehicle and enhancement of fuel economy.

• Smooth, moderate operation can yield savings in fuel
• Steady speeds without stopping will usually give the best fuel economy
• Idling for long periods of time may waste fuel
• Anticipate stopping; slowing down may eliminate the need to stop
• Sudden or hard accelerations reduce fuel economy
• Slow down gradually
• Drive at moderate speeds
• Revving the engine before turning it off may reduce fuel economy
• The air conditioner may reduce fuel economy
• Warming up a vehicle on cold mornings is not required and may reduce fuel economy
• While idling put the gear shift lever in the neutral position
• Resting your foot on the clutch pedal while driving may reduce fuel economy
• Combine errands and minimize stop-and-go driving
• Keep tires properly inflated. It is recommended to check your tire pressure in the morning when the tyre is cold
• Use recommended engine oil. Refer to the Maintenance Section for specifications and capacities
• Replace the fuel filter and air filter at the recommended intervals
• Shift gears at the recommended speeds and rpm bands only. Refer to the gear shifting speed table for further details
• Control the maximum speed between 90 to 100 kmph in 5th gear to achieve the best fuel efficiency
• Follow the recommended maintenance schedule and perform the owner maintenance checks recommended
• Heavily loading a vehicle or towing a trailer will reduce fuel economy
• Carrying unnecessary weight may reduce fuel economy
• Adding certain accessories to your vehicle may reduce fuel economy
• Four-wheel-drive operation (if equipped) is less fuel efficient than two-wheel-drive operation
• Driving on flat terrains offer improved fuel economy as compared to driving on hilly terrains
• Close windows during high speed driving for better fuel economy
• It is recommended to refuel in the mornings (cold weather condition)

11.6.1 How to Calculate Fuel Efficiency (Mileage)

1. Ensure recommended tire pressure is maintained
2. Refuel your vehicle till the fuel gun at the fuel station is auto-cut-off
3. Reset trip meter to zero
4. Drive at a moderate speed for a minimum distance of 100 km
5. Refuel at the same fuel station till the auto-cut-off mode
6. Assuming ‘a’ liters of fuel was filled and ‘b’ was the trip meter reading. Fuel Efficiency = b/a kmpl

11.7 Ignition Switch

An illuminator ring is provided on the face of the ignition switch to help in locating the ignition switch at night. The ring will illuminate the moment the driver door is opened and will remain glowing till the driver door is closed.

The different positions of the ignition switch are;

LOCK - This is the ignition and steering lock position. The vehicle circuits and engine is completely switched OFF. The steering wheel is also locked and the key can be removed from the ignition only in this position.

ACC - The steering is unlocked and can be rotated. In this position all electrical circuits are enabled. Use this mode when you want to listen to music, etc., with the engine temporarily switched OFF.

ON - All electrical circuits are enabled. Some of the warning or information lamps illuminate in this position. While some of the lamps will go out after a few seconds, some will continue to remain ON till the engine is started. When the vehicle is being driven, ignition switch remains in the ON position.

Do not leave the ignition in ON when the engine is OFF. This could lead to battery drain and ignition switch damage.

START - This position is to start the engine by cranking the starter motor. This is a momentary position. When the key is turned to start position, the starter cranks the engine. Once the engine is running, release the key, and the key reverts back to ON position and the starter motor disengages from the engine.

Do not continue cranking after the engine has started. This will lead to damage of the starter and other engine components.

If turning the key is difficult, jiggle the steering wheel from side to side and try again.

The key can be removed only in the LOCK position. When the key is removed, the steering column lock is activated and the steering wheel cannot be turned.

Never return the key to the LOCK position or try to remove the key, when the vehicle is in motion. Removing the key allows the steering wheel to lock. You will loose the control of the vehicle and may cause serious accident. Remove the key only when the vehicle is parked.

11.8 Transmission

The first few shifts on a new vehicle may be somewhat rough. This is a normal phenomenon, and precision shifts will develop within the initial few hundred kilometers of running.

11.8.1 Gear Lever

Your vehicle is fitted with manual transmission having six forward and one reverse gear. This shift pattern is imprinted on the gear lever knob. The transmission is fully synchronised in all forward gears so shifting to either a higher or a lower gear is easily accomplished. The clutch pedal should be depressed fully while shifting, and then released slowly.

11.8.2 Gear Indicator

The current gear lever position is indicated in the centre of the speedometer dial.

11.8.3 Neutral Position

This position stops the transmission of power from the engine to drive axle. With the gear lever in neutral and brakes released, the vehicle can move freely by pushing or towing. The engine can be started in this mode. It is always recommended to keep the brake pedal depressed in this position. It is advisable to shift into neutral when the vehicle is standstill for longer durations with the engine idling.

Coasting the vehicle with the gear lever in neutral and engine ON/OFF is not recommended. In an event of panic braking, you will not have the power of engine braking to slow down the vehicle. This may lead to personal injury or accident.

Do not leave the vehicle with the gear lever in neutral position. Always engage manual parking brake before leaving the vehicle, to prevent any vehicle movement leading to possible injury to a by-stander or damage to vehicle.

11.8.4 Gears 1-6

Use the gears 1 to 6 as per vehicle load, road/traffic conditions or as per requirement. The current gear selection is indicated in the cluster.

Always depress the clutch fully before moving the gear lever from the current position to any desired position. Perform up-shifts or down-shifts one gear at a time, do not jump gears.

11.8.5 Recommended Gear Shifting Speeds

Shift gears at suitable engine or road speeds to safeguard the transmission components. Avoid driving in high RPM’s (>3000 RPM).

When parking on an incline, gear alone may not be sufficient to prevent the vehicle from moving. Always set the manual parking brake in addition to shifting the gear lever into gear. It is also recommended to turn the front wheels towards the road curb

This gear is to enable the vehicle to move in the reverse direction. Move the gear lever into this position only after the vehicle has come to a complete stop and the gear lever is in neutral position.

The reverse lock ring located immediately below the gear shift knob must be pulled upward while moving the shift lever to the reverse (R) position.

To avoid transmission damage, shift into or out of reverse gear only after the vehicle has come to a complete stop and the engine is at idle speed. It is recommended you wait approximately for three seconds in neutral gear before shifting into or out of reverse gear.

For brief stops, e.g. at traffic lights, keep the gear shift in neutral and hold the vehicle with the brake pedal. For prolonged stops, it is recommended to switch OFF the engine and apply the parking brake. When stopping the vehicle on an uphill gradient, do not hold it with the clutch/accelerator; use the brake to avoid unnecessary clutch wear/heat buildup.

Do not leave children unattended in the vehicle or with access to an unlocked vehicle. Children could move the gear lever, which could result in an accident or serious injury.

On slippery/wet road surfaces, never downshift in order to obtain braking action. This could result in a wheel slip and reduced vehicle control.

To prevent the engine from laboring at a low RPM when driving uphill gradients or with your vehicle heavily loaded, downshift when necessary to maintain engine RPM within the best torque range. Similarly while driving downhill, downshift to utilize the engine braking in an optimum manner.

The idle speed is controlled automatically and it will decrease as the engine warms up.

Observe that all warning lamps are OFF when the engine is running.

After idling for a few seconds, follow the below steps to drive away;

1. Release the parking brake
2. Depress the clutch
3. Shift the gear lever to 1st gear
4. Release the service brake pedal
5. Drive by releasing the clutch and depressing the accelerator pedal simultaneously.

Avoid full throttle operation when the engine is cold and prolonged idling at low ambient temperatures. Long periods of idling may be harmful to your engine. Combustion chamber temperatures can drop so low that the fuel may not burn completely. Incomplete combustion allows carbon and varnish to form on piston rings and injector nozzles. Also, the unburned fuel can enter the crankcase, diluting the oil and causing rapid wear to the engine.

You must fuel this vehicle with Ultra Low Sulfur Diesel. For smooth functioning and reliable operation of the engine during cold weather conditions, use winter diesel for refuelling which is available at filling stations during winter months. Check with your fuel retailer for details.

The recommended engine coolant mixture will work fine till ambient temperatures do not drop below -32ºC approx. For ensuring above performance, it is a must that you use only recommended engine coolant.

11.10 Stop/Start System (if equipped)

Stop/Start system automatically “stops” and “starts” the engine when idle at signals or long traffic jams. This in turn gives a better fuel efficiency. Stop/Start system is activated by the “Stop/Start” button in the central bezel switch bank. The LED on the button indicates the status of the button.

11.10.1 How Does the Stop/Start System Work?

Let’s take a simple example of driving in traffic conditions within your city. Assume that your vehicle has stopped at a traffic junction due to a red signal. The following steps illustrate how the system functions.

• The vehicle has come to a halt at a traffic signal, is in the neutral gear and the clutch pedal is released
• The “Stop/Start” lamp in the cluster will blink indicating that the engine is going to stop shortly. The engine will shut down automatically after a specific time period
• The “Stop/Start” lamp will illuminate in the instrument cluster indicating the engine was stopped by the Stop/ Start System
• Once the signal turns green, press the clutch pedal and the engine starts immediately
• The indicator in the cluster goes OFF indicating that the engine has started again and you are ready to drive on

• Stop/Start System is activated using the Stop/Start button
• Bonnet is fully closed
• In the current ignition cycle, the vehicle has crossed 2 kmph at least once
• Current status of the engine is idling
• Vehicle speed is zero
• Accelerator pedal and clutch pedal are fully released
• Vehicle battery should be in healthy condition
• Engine is warm (Engine coolant temperature is between 25 °C and 100 °C). This is an extra precaution to ensure safe working of the engine
• Fuel temperature is less than 60 °C
• Gear in neutral

• Vehicle should have been stopped by the Stop/Start System
• Gear lever is in the neutral position, Clutch pedal is fully de-pressed
• Vehicle speed is zero
• Stop/Start System is in active state
• Bonnet should be closed

11.10.2 Overview of the Stop/Start System

11.10.3 Frequently Asked Questions (FAQ)

1. What is the advantage of the system?

   The Stop/Start System aids in attaining better fuel efficiency on your vehicle and thus reducing your running costs. However, the mileage improvement will depend upon various parameters such as prevailing traffic, driving patterns, etc.

2. What are the other advantages of the system?
   • Since the engine is switched off during traffic signals/ jams, considerable amount of CO2 release to the atmosphere is avoided. This reduces global warming and thus provides us with a cleaner atmosphere to live
   • Ability to start the engine by pressing the clutch pedal
   • Reduces noise pollution at traffic signals
3. Is it possible to start the engine through the clutch pedal for the first time?

   No, the engine can be cranked only with the ignition key for the first time. If the engine is stopped automatically by the system, only then it is possible to start the engine through clutch pedal.

4. How to activate/deactivate the system?

   The system is activated by default during every ignition cycle. The LED indication on the Stop/Start switch indicates the status of the system. The system can be turned OFF or back ON using the Stop/Start switch.

5. Whether the system will get activated as soon as the engine is started the first time with the ignition key?

   No, the Stop/Start system can be activated only by the Stop/Start switch, provided all listed conditions (in the previous section) are met. This is to ensure better performance of the engine in terms of fuel economy and durability.

6. What is to be done, if I don’t want the system to stop my engine at traffic signals/Jams?

   The system can be turned OFF by the Stop/Start button in the central bezel switch bank.

7. Whether the A/C will function, if the engine is switched off?

   No, the A/C will not work. However the blower will be in operation when the ignition is ON.

8. What will happen if I keep the clutch continuously pressed at traffic signals/jams?

   The system will not stop the engine if the clutch is continuously pressed since it indicates the driver’s intention of moving the vehicle immediately.

9. When the battery charge is low, whether the engine will be switched off?

   If the battery charge drops below a certain threshold level, the system will not stop the engine so as to preserve the battery from further draining.

10. Whether I will be able to operate the engine with the normal ignition key?

    Yes, normal operation with the ignition key is always possible.

11. Whether the vehicle will start (or) stop in gear?

    The vehicle will not start or stop automatically in gear to ensure safety. It will do so only in the neutral position of the gear lever.

12. Whether the system will stop my engine in moving traffic?

    No, the engine will be stopped only when the vehicle speed is zero.

13. Whether the audio system will be switched OFF, when the engine shuts down?

    No, the audio system will not be switched OFF and you can continue to enjoy the music.

14. Whether the engine will re-crank whenever the clutch pedal is pressed?

    No, when the engine is running, the starter motor will not attempt to re-crank.

15. If any component involved in the system fails, what will happen?

    The system has a built-in diagnostic module which understands the failure and immediately goes to bypass mode. In the bypass mode the engine can be turned ON and OFF by ignition key as usual.

11.11 Fuel

Use only commercially available vehicular Ultra-low Sulfur Highway Diesel that meets the BIS standard (Conforming to IS 1460;2010 BSIV/BSIII specification or equivalent). Information on diesel quality can normally be found in the fuel pump. Please contact filling station personnel in case labels in the pump cannot be found.

Do not fill the fuel tank or mix the fuel with gasoline, alcohol based fuels, kerosene, etc. This will damage the engine, fuel and exhaust system components.

If you have accidentally filled the fuel tank with incorrect or non-approved fuel, do not start the vehicle. Contact an Authorized Mahindra Dealer to have the fuel system drained completely.

11.11.1 Fueling during Winter

During freezing weather if fuel is not winterized or is insufficiently winterized, waxing/gelling may start in fuel, leading to interruption in fuel supply to engine. For smooth functioning and reliable operation of the engine during cold weather conditions, use winterized ULSD which are available at the filling stations during winter months. Check with your fuel retailer for further details.

Avoid inhaling fuel vapors and any skin or clothing contact. Direct skin contact with diesel or the inhalation of fuel vapor may affect your health

Diesel is highly flammable and poisonous. It burns violently and can cause serious injury. Never allow sparks, flames or smoking materials near diesel. Turn OFF the engine before refueling. Whenever you are around diesel, extinguish all smoking materials.

It is recommended maintaining a minimum of 10 liters of fuel in the fuel tank. Driving the vehicle till the fuel tank is empty is not recommended. Always have sufficient fuel in the tank. Check the fuel level prior to starting your journey.

Never carry fuel in separate containers in the vehicle, it is dangerous and may lead to inadvertent fuel leak or spillage.

11.11.3 Fuel-Lid Opening and Closing

The remote fuel-lid can be opened by gently pressing the fuel lid button (adjacent to the head lamp leveling switch) on the instrument panel driver side.

Fuel filler lid cannot be released when the vehicle speed is more than 20 kmph.

Fuel filler lid operation is limited to 8 times / minute. Avoid unnecessary usage of fuel filler lid button.

Turn the fuel cap counter-clockwise to open. Refuel and put the cap back in its place and tighten in the clockwise direction till three distinct clicks are heard. Close the fuel lid shut.

Ensure the fuel cap and lid are securely closed before starting the vehicle.

11.11.4 Mechanical Override for Fuel Lid Opening

In the unlikely event of remote switch not opening the fuel lid, a mechanical over ride release is provided. It is located in the luggage compartment LH trim area behind the third row seats. Turn the knob anti-clockwise to open the fuel lid.

12 WHEELS AND TYRES

12.1 Tire Information

12.2 Tyre Rating

Your vehicle is originally equipped with tyres supplied by a reputable manufacturer. If you ever have any questions regarding your tyres, please refer to literature supplied by the tyre manufacturer, or to the separate tyre warranty provided by the tyre manufacturer. You may also contact Mahindra directly, or the tyre manufacturer.

The tyre rating of XUV500 is;

• 235/65 R17 104H

Tyre rating is explained as below;

Callout (A): 235 (Three-digit number): This number gives the width in millimeters of the tyre from sidewall edge to sidewall edge. This is called as “Section Width”.

Callout (B): 65 (Two-digit number): This number, known as the aspect ratio, gives the tyres ratio of height to section width.

Callout (C): R: This is the Tyre Construction Code. The “R” stands for Radial.

Callout (D):17 (Two-digit number): This number is the wheel or rim diameter in inches.

Callout (E):104 (Two or three digit number): This number is the tyres load index. It is a measurement of how much weight each tyre can support.

Callout (F): H: Tyre speed rating or speed symbol. Never drive the vehicle faster than the tyre speed rating. The speed rating denotes the speed at which a tyre is designed to be driven for extended periods of time under a standard condition of load and inflation pressure.

12.2.1 Speed Rating

12.3 Tyre Label (Vehicle Placard)

Tyre Label (Vehicle Placard) is located on the driver side inner B-pillar. This placard tells you important information about tyre size designed for your vehicle, and the tyre inflation pressures for the front & rear tyres.

Never overload your vehicle. Overloading can cause tyre failure, affect vehicle handling, and increase your stopping distance, resulting in an accident and/or serious personal injury.

Improper inflated tyres can adversely affect vehicle handling or can fail unexpectedly, resulting in an accident and/or serious personal injury.

12.4 Tire Pressure

Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure;

• Safety
• Economy
• Ride Comfort and Vehicle Stability

Proper tire inflation contributes to a comfortable and safe ride. Overinflating produces a jarring and uncomfortable ride. Both underinflation and overinflation affect the stability of the vehicle and can produce a feeling of sluggish response or over responsiveness in the steering. Unequal tire pressures can cause erratic and unpredictable steering response or may cause the vehicle to drift left or right.

Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation also increases tire rolling resistance and results in higher fuel consumption.

The proper cold tire inflation pressure is listed in the Tire Label (Vehicle Placard), located on the front passenger side inner B-pillar.

12.4.1 Inspection and Adjustment Procedure

The tire pressure should be checked and adjusted, as well as inspected for signs of tire wear or visible damage, at least once a month. Use a good quality pressure gauge to check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are underinflated. At the same time, each tire should be inspected for signs of tire wear or visible damage.

Inflation pressures specified on the placard are always cold tire inflation pressures. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 km after a three-hour period. Check tire pressures more often if subject to a wide range of outdoor temperatures, as tire pressures vary with temperature changes. Tire pressures change by approximately 1 psi (7 kPa) per 7°C of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in the winter.

When it was new, the spare tire in your vehicle was fully inflated. However, a spare tire can lose pressure over time. In order to avoid being stranded, check the spare tire air pressure frequently.

12.4.2 Inflating Your Tires

Safe operation of your vehicle requires that your tires are properly inflated. Remember that a tire can lose up to half of its air pressure without appearing flat.

At least once a month or before long trips, inspect each tire and check the tire pressure with a tire gauge (including spare tire). Inflate all tires to the recommended inflation pressure.

Under-inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or “blowout”, with unexpected loss of vehicle control and increased risk of injury. Under-inflation increases sidewall flexing and rolling resistance, resulting in heat buildup and internal damage to the tire. It also may result in unnecessary tire stress, irregular wear, loss of vehicle control and accidents.

Always inflate your tires to the recommended pressure even if it is less than the maximum inflation pressure information found on the tire. The recommended tire inflation pressure is found on the Tire Label which is located on the front passenger side inner B-pillar. Failure to follow the tire pressure recommendations can cause uneven tread wear patterns and adversely affect the way your vehicle handles.

NOTICE

If you overfill the tire, release air by pushing the metal stem in the center of the valve. Then recheck the pressure.

After inspecting or adjusting the tire pressure, always reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the stem, resulting in an unexpected loss of tire pressure, an accident and/or personal injury.

12.4.3 Radial Ply Tires

Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly, resulting in an accident and/or personal injury. Always use radial tires in sets of four. Never combine them with other types of tires.