1.1 Introduction

Dear Customer,
Congratulations on purchasing Mahindra XUV500 AT. Your vehicle has been designed to provide years of safe and dependable service, as long as it is used and maintained in accordance with the instructions provided in this manual.

All persons who will use and/or maintain this vehicle must read, understand and follow all warnings and instructions provided in this manual. This Owner's Manual should be considered an integral part of the vehicle and should remain with the vehicle. However, nothing in this manual, and none of the safety devices installed in the vehicle, are a substitute for careful operation and common sense. Always make sure that your vehicle is in optimum working order, and take note of the road and weather conditions under which you are using your vehicle.

If you have any questions concerning the proper use or maintenance of your vehicle, please call your Authorized Mahindra Dealer. A list of dealers can be found in the Dealer Directory Supplement.

Alternatively you can contact Mahindra at,

• 1800-209-6006 (Toll free)
• customercare@mahindra.com

We extend our best wishes for safe and pleasurable motoring. Sincerely,
MAHINDRA & MAHINDRA LTD.

Servicing and Summary Data

• For all issues concerning the vehicle and for any need for spare parts, contact only the Authorized Mahindra network
• We recommend you always use genuine Mahindra spare parts when performing repairs on the vehicle
• We suggest that you record the vehicle data in the Service Coupon Booklet for future references

1.2 Safety Symbols

Carefully read, understand and follow the safety symbols/ instructions given in this manual.

To emphasize information and procedures regarding safety, use, maintenance, etc., the following symbols are used throughout the manual.

1.3 General Safety Information and Instructions

Failure to follow the warnings and instructions provided in this manual could result in failure of the vehicle, an accident and/or serious personal injury.

1. Carefully read, understand and follow the warnings and instructions given in this manual. This manual is an essential part of the product. Keep it in the vehicle glove box for future reference
2. Spare bulb and first aid kit are placed in the glove box of the vehicle. Ensure they are not taken out of the vehicle at any point of time.
3. Please note that throughout this manual, reference is made that “an accident” could occur. An accident could cause you or a bystander to sustain severe personal injury, or result in property damage
4. Never use a mobile phone or personal music device while driving. This may take your focus off the road and lead to accidents
5. Please be advised that many service and repair tasks require specialized knowledge, tools and experience. General mechanical aptitude may not be sufficient to properly service or repair your vehicle. If you have any doubt whatsoever regarding your ability to properly service or repair your vehicle, please contact your Authorized Mahindra Dealer or a qualified technician
6. Inspect the seat belt system periodically, checking for cuts, frays or wear in the seat belt webbing, or loose buckles, retractors, anchors or other loose parts. Damaged parts must be replaced immediately
7. Always start and operate the engine in a well-ventilated area. If in an enclosed area, vent the exhaust to the outside. Do not modify or tamper with the exhaust system
8. Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread and check sidewalls for any cuts, cracks, or other signs of wear. Replace as necessary
9. Always maintain the safety labels affixed to your vehicle in a good legible condition
10. All signal lamps, buzzers, shields, guards and other protective safety devices must always remain in place and in good, proper working condition
11. The life span of Mahindra products depend on many factors. Improper use, abuse or harsh use in general may compromise the integrity of the vehicle and significantly reduce its life span. The vehicle is also subject to wear over a period of time. Please have your vehicle regularly inspected by an Authorized Mahindra Dealer or a qualified mechanic. If the inspection reveals any damage or excessive wear, immediately replace or have the component serviced
12. We recommend that you use only genuine parts supplied by Mahindra. The use of non-Mahindra parts will not be covered by warranty
13. Never crawl under or be in close proximity to the vehicle when it is lifted off the ground (by a jack), unless the vehicle is properly supported with jack stands, wheel chocks and other appropriate safety devices
14. Never attempt any repairs or adjustments to any component while the vehicle is in motion. Always switch off the engine, and wait for the engine to come to a complete stop before performing any repairs or adjustments
15. The vehicle identification plates are the only legal identification reference, hence it is necessary to keep them in good condition. Never modify data on the plates or remove them. The customer is responsible for any possible tampering with the plates, which will immediately void the warranty
16. Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control. When the vehicle is fully loaded, drive at a slow speed, especially when turning. Note that the center of gravity of the vehicle increases as the vehicle is fully loaded on the roof carrier

1.4 To Owner’s of a Mahindra Vehicle

When first driving the vehicle after long periods of non-use, you may experience a temporary drive disturbance. This is a characteristic of the tires and should be no reason for concern. The condition should correct itself within 5-15 kms. of driving. If the disturbance persists, have the tires checked by an Authorized Mahindra Dealer.

Your driving ability can be seriously impaired by alcohol even if the blood alcohol level is far below the legal minimum. Drunken driving is one of the most frequent causes of accidents.

Never drink and drive. Drinking and driving will lead to an accident resulting in serious personal injury.

Your driving ability can be seriously impaired through the use of prescription or non-prescription drugs or medication (even cough syrup). If you are taking any sort of drug or medication, be sure that it will not affect your driving ability.

Use of electrical devices such as mobile phones, computers, portable radios or other by the driver while driving is dangerous. If use of a mobile phone is necessary despite this warning, use a hands free system to at least leave the hands free to drive the vehicle.

Please comply with the legal regulations concerning the use of communication equipment in vehicles in your country.

When you are driving over long distances, follow these tips so that you have a safe journey;

• Lack of sleep or fatigue may impact your ability to drive safely.
• Exercise your eyes by shifting the focus of your eyes to different parts of the road.
• Use stimulating beverages such as coffee or tea.
• Relax and stay calm.

Every one of us should play our part in protecting our environment. Judicious vehicle usage and disposing hazardous waste (including cleaning and lubrication fluids) are important steps towards this initiative.

Mahindra vehicles confirm to existing emission norms (standards). Adhering to the periodical maintenance schedule and using Mahindra genuine parts will help retain emission performance of the vehicle and is a pre-requisite to emissions warranty coverage.

If you have any questions concerning the proper use or maintenance of your vehicle, please call your Authorized Mahindra Dealer. A list of dealers can be found in the Dealer Directory Supplement or on the Internet.

Alternatively you can contact Mahindra on 1800-209-6006 / customercare@mahindra.com.

Driving smoothly during first 1000 kms. will help to prevent premature failures and abnormal system wear improving the life of drivetrain and vehicle components.

A new engine may consume more oil during the first 1000 kms. of running. This should be considered as a normal part of break-in and not interpreted as any problem with the engine.

To ensure optimum vehicle performance and passenger safety, your Mahindra vehicle is equipped with sophisticated modern electronics and controls. Do not install any communication devices, electronic gadgets or radar detection devices, without express written consent from Mahindra.

An improperly installed/adjusted two-way radio can adversely affect electronic systems.

1.5 Audio/Infotainment Manual

Please refer the Audio/Infotainment manual available in the manual pouch for details regarding;

• Audio/Video functions
• Bluetooth functions
• Navigation (if equipped)
• Map upgradation details

To upgrade the maps in your navigation system (if equipped), please refer the Infotainment manual.

2.1 Feature Matrix

In view of the policy of continuously improving our products, we reserve the right to alter specifications or designs without prior notice and without liability/obligation. Illustrations do not show the vehicle in the standard form. Please be aware that this manual may apply to various models/variants . As a result you may find some explanations for equipment not installed on your vehicle. All the information, illustration, and specifications in this manual are based on the latest product information available at the time of publication.

We recommend you to contact the nearest Mahindra dealer for latest features applicable to your vehicle.

2.2 Dimensions

2.2.1 Front View

2.2.2 Rear View

2.2.3 Side View

2.3 Lubricants and Capacities

2.4 Bulb Specification

2.5 Fuses & Relays

A fuse is the most common electric protection device. A fuse is placed in an electrical circuit, so that when current flow exceeds the rating of the fuse it blows off.

The element in the fuse melts, opening the circuit and preventing other components of the circuit from being damaged by the over current. The size of the metal fuse element determines the rating. Once a fuse blows off, it must be replaced with a new one.

Switch the ignition and all electrical equipment OFF before touching or attempting to change a fuse.

Fit replacement fuse with the same rating as the one you have removed.

You can identify a blown fuse by a break in the filament. All fuses except high current fuses are a push fit. A fuse puller should be used to remove the fuse from its position.

2.5.1 Engine Compartment Fuse Box

Engine compartment fuse box is located adjacent to vehicle battery. Release the lock to access the fuse box contents. Remove the fuse box cover by pressing the clips from both sides using both hands simultaneously. Spare fuses are provided in the fuse box for replacement of blown fuses. Ensure the correct rating fuse is replaced with the blown fuse.

2.5.2 Instrument Panel Fuse Box

Fully open the driver door and slide the driver seat backwards. The main central fuse box is located on the right side of the instrument panel. Price out the securing cover to access the fuse box.

2.5.3 Floor Fuse Box (W10 variant only)

The floor fuse box is located under the LH A-Pillar lower trim.

2.6 Flat Tire

In case of a flat tyre during driving, reduce your speed gradually, keeping a straight line. Move cautiously off the road to a safe place well away from traffic. Park on a level spot with firm ground. Stop the engine and turn ON your hazard warning flashers.

Firmly apply the parking brake. Have everyone come out of the vehicle on the side away from traffic.

Never stop your vehicle in a traffic lane to change a tire. You could be hit by an oncoming vehicle. Keep driving until you reach a safe location.

Lifting a vehicle to change a tyre or perform maintenance is very dangerous if you do not have the requisite tools, safety equipment and training. The jack provided along with the vehicle is to be used only for changing a spare tire. It is never to be used to perform any other maintenance or repair on the vehicle.

Never place any part of your body under any portion of the vehicle when it is supported only by the jack. You could be crushed by the vehicle if it falls off a jack. Keep by-standers away from the vehicle.

Find level, solid ground that is clear of oncoming traffic. If you cannot find a safe place to stop, it is better to drive on a flat tyre and damage the rim than it is to risk being hit by oncoming traffic.

After changing a flat tire, never store the tyre or other equipment in the passenger compartment of the vehicle. This loose equipment could strike an occupant in the event of a sudden stop or collision. Store all of these items in the proper place.

2.6.1 Tool Kit

The tool kit is located behind the third row seats on the floor.

The tool kit consists of the following tools packed in a PVC tool bag;

• Assembly Screw Jack
• Jack Operating Lever
• Wheel Spanner
• Tow Bar
• DEO Spanner 10mm x 12mm
• Screw Driver

The warning triangle is located on the rear door trim below the camping lamp. Rotate the two securing knobs and lower the hinged cover. Un-strap the two holding belts and remove the warning triangle pouch.

2.6.2 Spare Wheel Removal

Spare wheel is located below the floor at the rear end of the vehicle. It is held in place by a securing nut underneath the rear luggage compartment floor carpet.

• Locate the plug covering the securing nut below the rear luggage compartment floor carpet. Remove the plug using a coin.

• Loosen the securing nut counter clockwise to winch down/lower the secured spare wheel to the ground.
• Rotate the securing bracket counter clockwise and remove it out of the spare wheel hub
Remove/pull away the spare wheel

To remove the wheel cover, wrap the tip of a screw driver with cloth, insert it near the lugs of the wheel cover and pry the cover away from the wheel.

Do not try to pry off the wheel cover by hand alone. Take due care in handling the wheel cover to avoid unexpected personal injury.

2.6.3 Wheel Nut Loosening

Always loosen the wheel nuts before raising the vehicle. Turn the wheel nuts counter clockwise to loosen. To get maximum leverage, fit the spanner to the nut so that the handle is on the right side. Grab the spanner near the end of the handle and push down on the handle. Be careful that the spanner does not slip off the nut. Do not remove the nuts, but loosen them by one or two turns.

Do not apply force with your legs (or stand) on the wheel spanner while tightening the wheel nuts.

Block the wheel diagonally opposite the flat tyre to keep the vehicle from rolling when it is jacked up. When blocking the wheel, place a wheel block in front of one of the front wheels or behind one of the rear wheels.

2.6.4 Jacking

Locate the jack points in the front or rear as needed. They can be identified by a slot used to fit the jack precisely.

Position the jack at the correct jacking point. Make sure the jack is positioned on a level and solid place.

To raise the vehicle, insert the jack handle end with the jack operating lever, wheel spanner square slot into the jack operating lever and turn it clockwise with the handle. As the jack touches the vehicle and begins to lift, check that it is properly positioned.

Ensure no one is in the vehicle. Raise it high enough so that the spare tyre can be installed. Remember you will need more ground clearance when putting on the spare tyre than when removing the flat tire.

Make sure to set the jack properly in the jacking point. Raising the vehicle with jack improperly positioned will damage the underbody of vehicle or may allow the vehicle to fall off the jack and cause personal injury.

• Use the jack only for lifting your vehicle during wheel changing
• When raising the vehicle, do not place any objects on top of or underneath the jack.
• Do not raise the jack with someone in the vehicle.
• Raise the vehicle only high enough to remove and change the wheel.
• Follow jacking instructions
• Do not start or run the engine while your vehicle is supported by the jack.

Never get under the vehicle when the vehicle is supported by the jack alone.

Remove the wheel nuts. Lift the flat tyre straight off and place it aside. Roll the spare wheel into position and align the holes in the wheel with the bolts. Lift up the wheel and get at least the top bolt started through its hole. Wiggle the wheel and press it back over the other bolts.

Before putting on the wheels, remove any corrosion on the mounting surfaces with a wire brush or such. Installation of wheels without good metal to metal contact at the mounting surface can cause wheel nuts to loosen and eventually cause a wheel to come off while driving.

Reinstall the wheel nuts with the tapered end inward and tighten by hand. Press the wheel inward and tighten the wheel nuts further.

Never use oil or grease on the bolts or nuts. Doing so spanner slip, damage the bolts and also may cause personal injuries. Also, nuts may loosen and the wheels may fall off, which could cause a serious accident. If there is oil or grease on any bolt or nut, clean before installing wheel nuts.

Lower the vehicle completely and tighten the wheel nuts using the wheel nut spanner. Turn the jack operating lever counter clockwise using the wheel nut spanner to lower the vehicle, making sure the handle remains firmly fitted onto the jack handle extension. Do not use other tools or any additional leverage other than your hands, such as a hammer, pipe or your foot. Make sure the spanner is securely engaged over the nut. Tighten each nut a little at a time in the diagonally opposite order. Repeat the process until all the nuts are tight.

Improperly or loosely tightened wheel nuts are dangerous. The wheel could wobble or come off. This could result in loss of vehicle control and cause a serious accident. Always make sure all the wheel nuts are properly/securely tightened to the specified torque.

When lowering the vehicle, make sure all portions of your body and all other persons are clear off the vehicle as it is lowered to the ground. Have the wheel nuts tightened with the torque spanner to 83 -104Nm, as soon as possible after changing wheels.

Put the wheel cover into position aligning the nozzle on the wheel to the nozzle clearance on the wheel cover. Tap it firmly on the sides with your hand to snap it into place.

2.6.5 Restore all the Tools, Jack and Flat Tyre Securely

Replace the tools (jack, wheel spanner, etc.,) in their storage locations.

Align the spare wheel bracket to the centre hub of the wheel. Winch up the flat tyre to the floor at the rear of the vehicle. Firmly tighten the securing nut and put the floor carpet back.

Double check to ensure the tyre is snug against the rear floor of the vehicle. The spare wheel bracket/cable may be damaged if the vehicle is driven with the spare wheel loosely mounted.

Drive slowly to the nearest service station and inflate to the correct pressure. Always reinstall the valve cap after checking or adjusting tyre pressure, dirt and moisture could get into the valve core and cause air leakage or valve damage.

2.7 Identifying Components in the Engine Compartment

2.8 Technical Specifications

2.9 Vehicle Identification Number (VIN)

Vehicle Identification Number (VIN) is the legal identity of your vehicle. The vehicle identification number is stamped on the VIN plate riveted on to the bottom of the B-Pillar on the driver side.

2.10 Engine Number

The engine number is punched on the LHS face of the crankcase adjacent to the water pump. The engine number is also stamped on the VIN plate near the bonnet release lever.

3 VEHICLE OVERVIEW

3.1 Front Overview

3.2 Rear Overview

3.3 Instrument Panel Overview

4 INSTRUMENT CLUSTER OVERVIEW

4.1 Instrument Cluster

4.2 Warning Lamps Overview

4.3 Warning Lamps

Symbol	Warning Lamp/Tell Tale	Lamp Pre-check	Lamp Status while Engine running	Action/Remarks
	Parking Lamp	No	Continuously ON	Indicates Parking Lamp is ON
	Seat Belt Warning Lamp	Yes	Continuously ON	If tell tale is not turning OFF even after fastening the seat belt, contact an Authorized Mahindra Dealer for assistance
	AWD Lamp	No	Continuously ON	Indicates a malfunction of the AWD system. Contact an Authorized Mahindra Dealer Immediately
	Left Turn Indicator	No	Slow or Fast Blinking	Indicates left turn lamp is blinking Slow Blinking: Normal operation Fast Blinking: One /more left turn lamp bulb has fused. Have the bulb replaced
	Airbag Warning Lamp *	For about 2 seconds	Continuously ON	Indicates malfunction of the airbag system. Contact an Authorized Mahindra Dealer immediately
	Front Fog Lamp Indicator *	No	Continuously Lamp ON	Indicates front fog lamp is ON.
	Glow Plug Indicator	For about 2 seconds	Continuously ON	Indicates a malfunction in the starting system. Contact an Authorized Mahindra Dealer immediately
	Vehicle Armed Status Lamp	No	Blinking	Slow Blinking: Vehicle is armed with the remote Fast Blinking/Continuously ON: Indicates a system malfunction. Contact an Authorized Mahindra Dealer immediately
	Rear Fog Lamp Indicator *	No	Continuously ON	Indicates rear fog lamp is ON
	Low Fuel Warning Lamp	No	Continuously ON	Indicates fuel level has reached the reserve level. Re-fuel immediately.
	Water in Fuel Filter Warning	Yes	Continuously ON	Indicates water in fuel filter. Drain the water from filter or contact an Authorized Mahindra Dealer for assistance
	Right Turn Indicator	No	Slow or Fast Blinking	Indicates right turn lamp is blinking Slow Blinking: Normal operation Fast Blinking: One /more right turn lamp bulb has fused. Have the bulb replaced
	Cruise Control Indicator *	Yes	Continuously ON	Indicates vehicle is in Cruise mode
	High Coolant Temperature Warning Lamp	Yes	Continuously ON	Engine temperature very high. Contact Authorized Mahindra Dealer immediately
	Low Engine Oil Pressure Warning Lamp	Continuously ON till Engine Starts	Continuously ON	Indicates engine oil pressure is low. Check oil level and top-up or contact an Authorized Mahindra Dealer for assistance
	ESP System Warning Lamp*	For About 2 Seconds	Continuously ON or Blinking	Blinking: Indicates ESC has taken control of the vehicle stability Continuously ON: Indicates a malfunction in the ESC system. Contact an Authorized Mahindra Dealer immediately
	ABS Warning Lamp *	For About 2 Seconds	Continuously ON	Indicates malfunction of the ABS system. Contact an Authorized Mahindra Dealer immediately
	ESP OFF Lamp*	No	Continuously ON	Indicates ESC OFF
	Tiretronics	For About 2 Seconds	Continuously ON or Blinking	Blinking: Indicates ESC has taken control of the vehicle stability Continuously ON: Indicates a malfunction in the ESC system. Contact an Authorized Mahindra Dealer immediately
	Check Engine Lamp	For About 2 Seconds	Continuously ON or Blinking	Indicates a potential malfunction in the EMS, contact an Authorized Mahindra Dealer immediately
	Parking Brake ON/Brake Fluid Low Warning Lamp	Yes	Continuously ON	Either one of below conditions- 1. Park Brake might be engaged 2. Brake fluid level might be low 3. Front Brake Pads are worn Contact Authorized Mahindra Dealer immediately for assistance
	OBD Check Lamp	Continuously ON till Engine Starts	Continuously ON	There is a potential malfunction related to emission system, contact an Authorized Mahindra Dealer immediately
	Headlamp High Beam Indicator	No	Continuously ON	Indicates Head lamp high beam is ON
	AT Malfunction indicator Lamp	Continuously ON till Engine Starts	Continuously ON or Blinking	Indicates malfunction if lamp is ON after the engine starts
	Charging System Warning Lamp	Continuously ON till Engine	Continuously ON	Indicates malfunction in charging system. Contact Authorized Mahindra Dealer for assistance
	Door Ajar Warning Lamp	No	Continuously ON	Indicates one or more doors and/or boot/hood are open

5 SEATS AND SEAT BELTS

5.1 Front Seats

5.1.1 Sitting in Correct Position

Follow the tips below for a comfortable and safe journey;

• Sit in an upright position with the base of your spine pressed against the seat back
• The driver and front passenger seat head restraint has 5 positions. Adjust it as close as possible to the above specified position, with the top of the head restraint even with the top of your head
• Maintain sufficient distance between yourself and the steering wheel. Maintain at least a ten inch (10") distance from the centre of the steering wheel to your chest
• The top curve of the steering wheel should align with your chin for ideal road visibility
• Adjust your seat and seat back angle such that your wrists rest on the steering wheel
• Ensure your legs are in bent position while fully depressing the clutch pedal.

The seat should be adjusted while still maintaining control of the foot pedals (able to fully depress the clutch pedal), steering wheel (rest the wrists on the steering wheel) and your view of the instrument panel controls.

Never adjust the driver's seat while the vehicle is in motion. The seat may unexpectedly move and cause the driver to unintentionally operate the accelerator or brake, or turn the steering wheel, causing loss of control of the vehicle, an accident or serious personal injury. Adjust the driver's seat only when the vehicle is not in motion.

Never put objects under the seats. They may interfere with the seat-lock mechanism or unexpectedly activate the seat position adjusting lever, causing the seat to suddenly move, resulting in loss of control of the vehicle, an accident or serious personal injury.

While adjusting the seat, do not put your hands under the seat or near the moving parts. This may lead to injuries.

5.1.2 Manual Front Seat Slide Adjustment

Move the seat forward or backward by lifting the adjustment lever located under the seat front and release once the desired position is reached.

While adjusting the seat, make sure the latch engages fully and the seat is locked firmly in the desired position. An unlocked seat may move in a sudden stop or collision, causing injury to the person in that seat. Push and pull on the seat to be sure it is locked.

5.1.3 Manual Front Seat Recline Adjustment

To adjust the seat back, lift the lever located on the outboard side of the seat, lean back, and release the lever at the desired position. To return the seat back, lift the lever, lean forward, and release the lever.

The seat belts provide maximum protection in a frontal or rear collision when the occupants are sitting up straight and well back in the seats. If you are reclined, the lap belt may slide past your hips and apply restraint forces directly to the abdomen, or the shoulder strap may contact your neck. The more the seat is reclined, the greater the risk of serious injury.

When returning the rear-reclined seat back to its upright position, make sure you support the seat back while operating the lever.

5.1.4 Front Seat Lumbar Adjustment (if equipped)

Both the front seat backs feature lumbar adjustment. The lumbar contour of the lumbar support can be adjusted by means of the adjusting wheel on the inner side of the seat back.

Properly adjusted lumbar support provides adequate back support essential during long journeys.

5.1.5 Manual Front Seat Height Adjustment

The driver seat height can be raised or lowered to three positions.

To RAISE the seat height, lift the seat height adjust handle while there is no load or prior to occupying the seat. Release the lever once desired seat height is reached.

To LOWER the seat height, lift the seat height adjust handle while seated in the driver seat. Release the lever once desired seat height is reached.

5.2 Power Seat (Driver Side only) (if equipped)

The power seat provides 6 - way electrical adjustments for the driver seat. It is equipped with electrically operated power slider, power recliner and power height adjustment mechanisms.

The graphics on the switches guide you to the function it has been assigned.

• Power seats will be operated even when the ignition switch is turned to the “OFF” position. However, to prevent battery discharge, operate your seats when the engine is running.
• Do not use two or more seat adjustment buttons simultaneously. It can damage the motor. Be sure to operate the electric seat button one by one.
• Do not forcibly operate any power adjustment switch if the seat comes in contact with other object and cannot be adjusted anymore.
• If the power seats are not operational, the seats should be checked and fixed before any driving.

5.3 Head Restraint

Your vehicle seats are equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of rear collision.

The head restraint comprises of the padded portion which contacts your head and is inserted/locked in receptacles on the top of the seat back.

Always align top of the head restraint with the top of your head or as close to it as possible. To raise the head restraint, press the lock knob and pull the restraint up. To lower the head restraint, press the lock knob and push the head restraint down.

The head restraint can be pulled out completely by depressing the locking button while pulling the restraint out.

Align the head restraint shafts over the holes on the seat top and push the restraint straight down till you hear the lock click.

Adjust the seat back so as to ensure that the head rest’s top is behind and not beneath the crown of your head

Never drive with the head restraints not properly adjusted, head restraints removed or inserted in a flipped condition. With no support behind your head, your neck could be seriously injured in a collision.

Head restraints are provided for the front row and second row outboard occupants.

5.4 Second Row Seats

Keeping luggage on the seats is dangerous. The luggage can become a projectile that could hit and injure passengers in a sudden stop or collision. Luggage should always be kept on the floor.

To avoid serious injury, do not sit on or place objects on a folded seat back while the vehicle is moving.

5.4.1 Second Row Seat Recline

To change the second row seat back angle, lean forward slightly while raising the recline lever on the top corner of the seat back, lean back to the desired position and release the recline lever. Make sure the recline lever returns to its original position and the seat back is locked in place by rocking the seat back forward/backward.

When returning the rear-reclined seat back to its upright position, make sure you support seat back while operating the lever.

5.4.2 Second Row Seat Folding (Third Row Seat Access)

The second-row seat can be flipped forward to provide more cargo space.

• Lower the second-row seat head restraint to the lowest position (else it will obstruct and hit the floor)
• Insert the lap belt into the pocket of the seat bottom
• Recline the seat back to full forward direction

• Push side actuation lever (B) in forward direction for Ingress, OR
• Pull rear actuation lever (A) for Egress

• Push seat back to rear side of vehicle for locking
• Pull seat back for upright position till it locks in design position
• Push seat cushion downward by sitting on it (>45 kg) for locking seat cushion

Return the seat back to its upright position in one continuous motion to securely lock the seat and in turn avoiding seat flipping forward suddenly leading to injuries. If this happens, release the seat lock by pulling the lever and repeat the procedure.

Be cautious when placing your hands around the seat anchors. You could pinch your hands or fingers between the seat anchor and the seat. Hold the edge of the seat when lowering it into place. Never place your hands between the seat anchor and the seat.

5.5 Third Row Seats

Refer to the previous sections for details regarding folding of second row seats.

5.5.1 Third Row Seat Folding

To fold the third row seat, unlock the seat back by pulling the lever on the rear of the seat back outwards.

Similarly lower the other half of third row seat to get a completely flat surface.

Both the second row and third row seats can be folded flat to maximise the luggage space.

5.6 General Warnings and Instructions- Seat Belts

At least once each month, inspect the seat belt webbing for any cuts, tears, or other signs of wear (such as fraying along the edges). Also inspect the anchors, retractors, and buckles to be sure they are tight and operational.

• All occupants, including the driver, should always wear their seat belt no matter how short the trip in order to minimize the risk of severe injury in the event of a crash. In an accident, an un-belted passenger becomes a projectile, and can cause serious injury to himself or another passenger.
• In a rollover crash, an un-belted person is significantly more likely prone to Injury than a person wearing a seat belt
• In order to be properly buckled, you must always sit up straight and keep your feet on the floor in front of you. The lap part must be worn low and tight across your hips, just touching the top of your thighs. While fastening the seat belt, the shoulder strap of the seat belt must pass over your chest and top of your shoulder. It must never touch your neck, face, the side of your shoulder, arm, or pass under your arm. The belt must always be flat against your body and not twisted in any way. Nothing, such as an arm rest, a pocketbook, or any external objects should be between you and the seat belt. Improper wearing of a seat belt will reduce the protection in an accident.
• Seat belts should be adjusted as tightly as possible, consistent with comfort to properly secure the wearer in the seat.

• The seat belts provided for your vehicle are designed for people of adult size, must be properly used and maintained.
• For usage of adult seatbelt to secure children refer to section on manual for child seat positions and use a child restraint systems

• Passengers should not move out of or change seats while the vehicle is moving. A passenger who is not wearing a seat belt can be thrown against the inside of the vehicle, against other occupants, or out of the vehicle during a crash or emergency stop
• Do not use any accessories on seat belts or modify in any way the seat belt system. Devices claiming to improve occupant comfort or reposition the seat belt can reduce the protection provided by the seat belt and increase the chance of serious injury in a crash
• An accident or emergency stop, can damage your seat belt system, even if the accident is “minor”. Please have your Authorized Mahindra Dealer inspect the seat belt system after an accident
• Please be aware that any unsecured item in your vehicle, such as your pet, unsecured child restraint system, a laptop or mobile phones, can become a projectile in the event of an accident or sudden stop, causing injuries to occupants in the vehicle

Never use a damaged seat belt system. A damaged seat belt will not provide protection in an accident, resulting in serious injury.

• Seat belt systems can be prone to abuse. They are not indestructible. They must be handled with care to avoid damage
• Keep the belts clean and dry. Belt retraction may become difficult if the belts and webbing are soiled. If they need cleaning, use a mild soap solution or lukewarm water. Never use bleach, dye, or abrasive cleaners. These chemicals will severely weaken the belts
• Retractors in 3-point type seat belts retract the seat belts when not in use. The inertia lock and coil spring allow the belts to remain comfortable on users during normal driving. During accidents or abrupt stops, inertia locks restrict the sudden forward movement of the wearer

Persons with serious medical conditions should also wear a seat belt. Consult your doctor for specific recommendations before travel.

Pregnant women must also wear seat belts. Consult your doctor for specific recommendations.

The lap belt should be worn snugly and as low as possible over the hips. The shoulder belt should be worn across your shoulder, but never across the stomach area. When worn properly, the seat belt will protect both the mother and the foetus in an accident or emergency stop.

A pregnant woman should never wear the seat belt across the stomach area. This could lead to serious injuries to the foetus and/or the pregnant mother.

Never wear twisted seat belts. Excessive forces will be transferred from the belt to the wearer, in a collision, resulting in serious personal injury. Each seat belt is meant for use by one person only. Using one seat belt for more than one person at a time is dangerous. The seat belt will not be able to spread the impact forces properly leading to serious injuries.

Never put a belt around a child being carried on the occupant's lap. This could lead to serious injuries.

• Reduce the possibility of being thrown from your vehicle
• Reduce the possibility of injuries to upper body, lower body and legs during an accident
• Hold the driver in a position which allows better control of the vehicle

Children who are too large for child restraint systems should always occupy the rear seat and use the vehicle seat belts. The lap portion should be fastened snug on the hips and as low as possible and the shoulder strap should be across the child's shoulder, not the neck or face. If you are unable to position the strap across the child's shoulder, the child should remain in a booster seat. Frequently check the seat belt to be sure it remains snug and in position. A squirming child could cause the seat belt to come out of position.

5.7 Fastening the Seat Belt (3-Point type)

Adjust the seat as needed, sit up straight and well back in the seat. To fasten your seat belt, pull the webbing out of the retractor and insert the metal tab into the buckle. An audible “click” would be heard when the tab locks into the buckle. Pull up on the shoulder strap to tighten the lap belt across your hips. The seat belt retractor will pull in any slack in the shoulder strap. A slow and easy motion will allow the belt to extend and let you move your body around freely.

Periodically check the seat belt as you ride to be sure it remains snug and in position. If there is a sudden stop or impact, the belt will lock into position. It will also lock (restrict) if you try to lean forward too quickly.

If the driver or co-driver seat belt is not fastened when the ignition is switched ON, the seat belt warning lamp illuminates. Refer “Warning Lamps” in the “Features and Control” chapter for further details.

5.8 Fastening the Seat Belt (2-Point Lap type)

This seat belt is applicable to the second row middle passenger seat. Insert the tongue into the buckle until it snaps. Position the lap belt on the hips as low as possible.

5.9 Unfastening the Seat Belt (both 3-Point & 2-Point)

To release the belt, press the buckle release button and allow the belt to retract. If the belt does not retract smoothly, pull it out and check for kinks or twists. Then make sure it remains untwisted as it retracts.

Never insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and may cause damage to the buckle mechanism, thereby making the seat belt ineffective in an accident, resulting in serious personal injury.

5.10 Seat Belt Height Adjuster ( If Equipped)

You can adjust the height of the shoulder belt anchor for maximum comfort and safety in both front seats. If the height of the seat belt is too near your neck, you will not be getting the most effective protection. The shoulder portion of the belt should be adjusted so that it lies across your chest and midway over your shoulder nearest to the door and not your neck.

To adjust the height of the seat belt anchor, lower or raise the height adjuster to an appropriate position while pressing the height adjuster button. Release the button to lock the anchor into position. Try sliding the height adjuster to make sure that it has locked into the position.

Adjust the shoulder belt height sitting well back in the seat. Do not adjust the seat belt height while vehicle is in motion.

5.11 Child Restraint System (CRS) (if equipped)

Use a child restraint system only if the child is not big enough to properly wear the seat belts. Else, use the regular seat belt instead of the child restraint system. Seat the child in the rear seat and use the seat belt. According to accident statistics, children are safer when properly restrained in the rear seat than in the front seat. Always secure a child in a proper child restraint system in accordance with age and size of the child as recommended by the child restraint system manufacturer.

Do not allow children to stand up or kneel on either the rear or the front seats. An unrestrained child could suffer serious injuries during emergency braking or collision. It is also not recommended that children travel sitting on your lap as it does not provide sufficient restraint.

6 SUPPLEMENTAL RESTRAINT SYSTEM (SRS) (if equipped)

6.1 Airbag

• One frontal airbag for the driver (A)
• One frontal airbag for the front passenger (B)
• Two side (seat) impact airbag’s (C) (if equipped)
• Two curtain airbag’s (D) (if equipped)

6.1.1 Airbag Location

• In the steering wheel hub - Driver Airbag


• Above the upper glove box - Passenger Airbag

• Outboard side of driver and front passenger seats - Side Impact Airbag’s


• In the inner roof rail (LH & RH) - Curtain Airbag’s

An airbag is not designed to deploy in every type of crash. Depending on the type of accident or impact, the front airbag’s, side airbag’s and curtain airbag’s independently deploy thereby protecting the occupants. It is not necessary that ALL the airbag’s deploy during an accident.

To minimize the risk of severe injury in the event of a crash, every passenger must always wear their seat belt (see the chapter on Seat Belts in this manual). The airbag’s inflate very quickly with great force. Do not position any part of your body too close to a airbag, you or especially children could be seriously injured by a deploying airbag.

6.2 Driver and Front Passenger Air Bag

Your vehicle is equipped with a Supplemental Restraint System (Airbag) and lap/shoulder belts at both the driver and front passenger seating positions. The indications of the system's presence are the letters “SRS AIR BAG” embossed on the airbag pad cover in the steering wheel and the passenger's side front panel pad above the glove box.

The SRS is designed to deploy the front airbags only when an impact is sufficiently severe and when the impact angle is less than ± 30° from the forward longitudinal axis of the vehicle.

Front airbags are not intended to deploy in side-impact, rear impact or rollover crashes. In addition, front airbags will not deploy in frontal crashes which are below the prescribed deployment threshold where risk of serious injuries is low.

Do not place any objects over the airbag or between the airbag and yourself.

6.3 Side Impact Airbag

Your vehicle is equipped with side impact airbag’s in both the front seats. The purpose of the air bag is to provide the vehicle's driver and/or the front passenger with additional protection during side impacts or collisions.

The side impact air bags are designed to deploy only during certain side-impact collisions, depending on the crash severity, angle, speed and point of impact.

• In the case of a side collision, the curtain air bag may be deployed together with the relevant side air bag on the side the collision occurs.
• The side impact air bag is supplementary to the seat belt systems and is not a substitute for them. Therefore your seat belts must be worn at all times while the vehicle is in motion. The air bags deploy only in certain side impact conditions severe enough to cause significant injury to the vehicle occupants.
• For best protection from the side impact air bag system and to avoid being injured by the deploying side impact air bag, all seat occupants should sit in an upright position with the seat belt properly fastened. The driver's hands should be placed on the steering wheel at the 9:00 and 3:00 positions. The passenger' arms and hands should be placed on their laps.
• Do not use any accessory seat covers. Use of seat covers could reduce or prevent the effectiveness of the system.
• Do not install any accessories on the side or near the side impact air bag.
• Do not place any objects over the air bag or between the air bag and yourself.
• Do not place any objects (an umbrella, bag, etc.) between the door and the seat. Such objects may become dangerous projectiles and cause injury if the supplementary side impact air bag inflates.

6.4 Curtain Airbag

Curtain air bags are located along both sides of the roof rails on the A & B pillars.

They are designed to help protect the heads of the front seat occupants and the rear outboard seat occupants in certain side impact collisions.

The curtain air bags are designed to deploy depending on the crash severity, angle, speed and impact. The curtain air bags are not designed to deploy in all side impact situations, collisions from the front or rear of the vehicle or in rollover situations.

• In the case of a side collision, the side air bag may be deployed together with the relevant curtain air bag on the side the collision occurs.
• In order for side and curtain air bags to provide the best protection, both front seat occupants and both outboard rear occupants should sit in an upright position with the seat belts properly fastened. Importantly, children should sit in a proper child restraint system in the rear seat.
• When children are seated in the rear outboard seats, they must be seated in the proper child restraint system. Make sure to position the child restraint system as far away from the door side as possible, and secure the child restraint system in a locked position.
• Do not allow the passengers to lean their heads or bodies onto doors or place objects between the doors and passengers when they are seated on seats equipped with side and/or curtain air bags.

6.5 Airbag System Malfunction Lamp

Airbags do not require any regular maintenance of service. The airbag system malfunction lamp illuminates when the ignition is ON, and it turns OFF after about two seconds as self check confirming normal operations of airbag system and malfunction lamp.

This lamp monitors airbag sensor assembly, airbag sensors, indicator lamp, seat belt pre-tensioner assemblies, inflators, interconnecting wiring and power sources.

If either of the following conditions occur, there is a malfunction of the airbags or seat belt pre-tensioner. Immediately contact your Mahindra Dealer.

• The lamp does not glow when the ignition is switched ON or glows beyond six (6) seconds after switching the ignition ON
• The lamp comes ON at any other time, even briefly
• The lamp comes ON intermittently

Never make any modifications to your vehicle which could affect the performance of your airbag system. In particular, changes to the vehicle frame, bumpers, bull bar, front fenders, ride height, suspension, seat belts, interior trim, seats or steering wheel (especially covers, pads or other trim), could prevent proper deployment of the airbag. If you need to make any modifications to accommodate any disability you may have, please contact your authorized Mahindra dealer.

Never try to open or strike the airbag cover. If the airbag cover is cracked or damaged in any way, the airbag may not function as intended. Take the vehicle to an Authorized Mahindra Dealer.

Even if the airbags do not deploy during an accident, take your vehicle to an authorized Mahindra Dealer for a thorough inspection of the airbag and seat belt systems, no matter how minor the accident. The airbag system could have been damaged, and may not work as intended in the future, resulting in serious injury.

6.6 Airbag Inflation/Deployment

The airbag sensors constantly monitor the forward deceleration of the vehicle. If an impact results in a forward deceleration beyond the designed threshold level, the system triggers the airbag inflators. This initiates a chemical reaction which quickly fills the airbags with non-toxic gas.

Upon deployment, tear seams molded directly into the pad covers separate under pressure from the expansion of the airbags. Further opening of the covers allows full inflation of the airbags. A fully inflated airbag, in combination with a properly worn seat belt, slows the driver's or the passenger's forward motion, reducing the risk of head and chest injury.

After complete inflation, the airbag immediately starts deflating, enabling the driver to maintain forward visibility and the ability to maneuver or operate other controls.

Deployment of the airbags happen in a fraction of a second, producing a loud noise releasing a ‘white smoke’ and residue along with a non-toxic gas. This does not indicate a fire. This smoke may remain inside the vehicle for some time, and may cause some minor irritation to the eyes, skin or breathing. Be sure to wash off any residue with soap and water as soon as possible to prevent any potential skin irritation. If you can safely exit the vehicle, you should do so immediately.

• Do not modify, remove, strike or open the seat belt pre-tensioner assemblies, airbag sensor or surrounding area or wiring. Failure to follow these instructions may prevent them from activating correctly, cause sudden operation of the system or disable the system, which could result in serious injury.
• Parts of the airbag module (steering wheel hub, airbag cover and inflator) may be hot for several minutes after deployment. The airbags inflate only once
• Do not cover the steering wheel, instrument panel, seats with any object (e.g. dash panel covers, seat covers) which may prevent the airbags from inflating properly
• The airbags inflate with considerable force. While the system is designed to reduce serious injuries, primarily to the head and chest, it may also cause other, less severe injuries to the face, chest, arms and hands. These are usually in the nature of minor burns or abrasions and swelling, but the force of a deploying airbag can also cause more serious injuries, especially if an occupant's hands, arms, chest or head is in close proximity to the airbag module at the time of deployment. Sit straight and well back into the seat. Move your seat as far back as practical to allow room for airbag inflation, while still allowing you to properly operate/drive the vehicle
WARNING
• The front passenger should never sit on the edge of the seat, stand near the glove compartment, rest feet or other parts of the body on the dashboard when the vehicle is moving.

WARNING
• The driver or front passenger who is too close to the steering wheel or dashboard can be seriously injured during airbag deployment.
• The driver must sit as far back as possible from the steering wheel while still maintaining control of the vehicle
• The front passenger must sit as far back as possible from the dashboard
• Sitting improperly or out of position can cause occupants to be shifted too close to a deploying airbag, strike the interior structure or be thrown from the vehicle resulting in serious injury

• Always sit upright with the seat back in an upright position, on the seat cushion centre with your seat belt on, legs comfortably extended and your feet on the floor
• All vehicle occupants must be properly restrained using the seat belts
• All infants and children must be placed in the rear seat of the vehicle in a child restraint seat and be properly restrained by seat belts
• Front airbags can injure occupants improperly positioned in the front seats
• Even with airbags, improperly belted and un-belted occupants can be severely injured when the airbag inflates. Always follow the precautions about seat belts, airbags and occupant safety contained in this manual
• Do not modify the front seats. Modification of the front seats could interfere with the operation of the supplemental restraint system or side impact airbags
• Do not place items under the front seats. Placing items under the front seats could interfere with the operation of the supplemental restraint system sensing components and wiring harnesses

6.7 Child Restraint and Airbag

Never place a rear-facing child restraint in the front passenger’s seat. If the airbag deploys, injuries to the child may be fatal..

In addition, do not place front-facing child restraints in the front passenger’s seat either. If the front passenger airbag inflates, it could cause serious or fatal injuries to the child.

• Extreme Hazard! Do not use a rear facing child restraint on a seat protected by an airbag in front of it!
• Never put a child restraint in the front passenger’s seat. If the front passenger airbag inflates, it can cause serious or fatal injuries.
• Never hold an infant or child on your lap. The infant or child could be seriously injured in the event of a crash. All infants and children should be properly restrained in appropriate child safety seats or seat belts in the rear seat.
• Install the child restraint system on the rear outboard seats, and securely lock the child restraint system in position.
• Always Buckle Children (ABC) in the back seat. It is the safest place for children of any age to ride.

6.8 Airbag Deployment

The images shown in this section are for illustrative purpose only. They may not look like your model/variant or vehicle.

Front air bags are designed to inflate in a frontal collision depending on the intensity, speed or angles of impact of the front collision.

Airbag Non-deployment

Impacts below a pre-determined threshold level may not cause the airbag’s to deploy in the following cases:

Air bags may not inflate if the vehicle collides with objects such as utility poles or trees, where the point of impact is concentrated to one area and the full force of the impact is not delivered to the sensors.

Running under a truck's tail gate may not provide the decelerations necessary for airbag deployment. Air bags will not inflate in this “under-ride” situation where deceleration forces that are detected by sensors are significantly low.

Frontal air bags are not designed to inflate in rear collisions, where occupants are moved backward away from the airbags by the force of the impact. In this case, inflated air bags would not be able to provide any additional benefit.

Frontal impact beyond 30º range from head-on to the vehicle.

Driving into a big pot-hole, stepped surface or hitting the far side of a hole/incline will not inflate the airbag.

Air bags will not inflate in rollover accidents where air bag deployment would not provide protection to the occupants. However, side impact and curtain air bags may inflate when the vehicle is rolled over by a side impact collision.

Frontal offset impact to the vehicle may not provide the deceleration force necessary for airbag deployment. In an angled collision, the force of impact may direct the occupants in a direction where the air bags would not be able to provide any additional benefit, and thus the sensors may not deploy any air bags.

6.9 Airbag Replacement

Self-servicing or tampering with the airbag system is dangerous. An airbag could accidentally deploy causing serious injuries, or will not deploy when there is a need. Always take your vehicle to an authorized Mahindra dealer for inspection and repairs.

6.10 Self Removing SRS Related Parts

Self removing the instrument panel, steering wheel, seats or airbag related parts or sensors is not recommended. Airbags could accidentally activate and cause serious injuries, or they may not deploy when there is a need. Visit an authorized Mahindra dealer if these parts must be removed.

6.11 Airbag Disposal

Improper disposal of an airbag or a vehicle with live airbags can be extremely dangerous. Approach an authorized Mahindra dealer to do these jobs.

6.12 Airbag Repair

If the front airbag cover or IP airbag cover shows signs of damage or having been removed, the vehicle should be towed to the nearest authorized Mahindra dealer for repair. Do not attempt to self repair or reinstall the cover.

6.13 Airbag Maintenance

For cleaning the airbag covers/areas, use only a soft dry cloth or one which has been moistened with plain water. Solvents or cleaners could adversely affect the airbag covers and proper deployment of the system.

7 LOCKS AND KEYS

XUV500 comes with two keys. Your key number is given on the tag attached to the key. It is recommended that you record the key number and store in a safe place. The keys operate all locks in your vehicle including those of the doors and ignition with steering lock. We advise you to keep one of these keys at a safe place for emergency use, but not in the vehicle.

Press the key release button on the RKE to unfold the key.

Never leave the key in the ignition switch with children in the vehicle. A child could switch on the ignition, start the engine, operate power windows and other controls, or move the vehicle, resulting in personal injuries to the bystanders and/or children seated inside.

7.1 Doors

7.1.1 To Open a Door from Inside

Pull the door lever away from the door and push the door outward to open.

7.1.2 To Open a Door from Outside

Pull the door handle firmly outwards to unlock and swing the door open.

7.1.3 Locking/Unlocking Individual Doors from Inside

Individual doors can be locked/unlocked from inside by the respective door lock tabs. Lift the lock tab outwards to unlock or press the tab inwards to lock that particular door.

Locking the driver door from inside activates the central locking system, thereby locking ALL the doors of the vehicle. Refer to Central Locking section for further details.

7.1.4 Manual Locking/Unlocking Doors from Outside

The driver/co-driver door can be manually locked/unlocked from outside by using RKE. Open the key by pressing the key release button on the RKE. The key is bi-directional; you can insert it into the key hole either way. Turn the key anticlockwise to lock or clockwise to unlock the door.

A key hole is provided in the driver door and front passenger door, to lock/unlock the doors manually from outside.

Locking the driver door from outside activates the central locking system, thereby locking ALL the doors of the vehicle. Refer to Central Locking section for further details.

7.1.5 Locking/Unlocking the Back Door

The back door can be manually unlocked by pressing the unlock button under the rear applique.

To close the back door, lower the back door half way down and allow it fall on its own weight. The door is locked automatically

7.2 Central Locking System

All doors of the vehicle can be simultaneously locked or unlocked from the driver door.

7.2.1 Central Locking/Unlocking All Doors from Outside

To manually lock/unlock all the doors from outside using the RKE, turn the key anti-clockwise (A)/clockwise (B) respectively in the driver door key hole.

In case the back door is open when the central locking is activated, the back door will not be locked even if it is closed later.

If any other door is open when central locking is activated, the system locks the open doors when they are closed.

7.2.2 Central Locking/Unlocking All Doors from Inside

Press the driver door lock tab down (A) to lock or lift the lock tab up (B) to unlock all doors simultaneously.

7.2.3 Child Safety Rear Door Lock

Your vehicle is equipped with left and right side child safety rear door locks. When the lock mechanism is engaged, the rear door(s) cannot be opened from the inside. The door(s) can only be opened from the outside.

To activate the child safety right rear door lock push the lever down (A) till you hear a distinct click indicating the activation of the child lock.

To de-activate the child safety right rear door lock pull the lever up (B) till you hear a distinct click indicating the deactivation of the child lock.

If the rear doors are not operable from inside, ensure that the child safety locks have been disabled.

Mahindra strongly recommends that the child safety rear door locks be used whenever there are children traveling in the rear seat.

7.3 Remote Keyless Entry (RKE) System

The front side of the RKE has three control buttons; Unlock, Lock and Search buttons. There is also a mechanical key release button (D). The Remote Keyless Entry (RKE) system operates on Radio Frequency (RF). You can insert the key into the ignition with either side up.

7.3.1 Precautions while handling RKE:

• Do not cover the key grip with any material that cuts off RF waves
• Do not leave the key exposed to high temperatures for a long period, such as on the dashboard or hood under direct sunlight
• Do not put the key in any liquid or wash it in an ultrasonic washer

7.3.2 To Lock and Arm the Vehicle with RKE

Press the lock button on the RKE for locking and arming the vehicle. When the vehicle is successfully locked and armed using the RKE, the hazard lamps flash once. If there are any open doors, the hazard lamps flash five times along with audible beeps indicating the same.

The audible beeps heard during the door open status can be muted/unmuted by pressing the lock button on the RKE for more than 3 secs.

• If any of the doors, except the driver door, are open while locking the vehicle with RKE, the vehicle locks all doors (door locks) irrespective of the open door/doors. When the open door(s) is/are closed later, the vehicle is locked and armed.
• If the driver door is open while locking the vehicle with RKE, the vehicle is not locked or armed. Close the driver door and lock the vehicle again with RKE to arm the Anti-theft system.

7.3.3 Unlock and Disarm the Vehicle with RKE

Press the unlock button on the RKE to unlock and disarm the vehicle. When the vehicle is unlocked and disarmed using RKE, hazard lamps flash twice

7.3.4 Theft Alarm

If there was an unauthorized attempt to open/start the vehicle by someone from the time you had locked and armed the vehicle to the time you press the unlock button of RKE, the hazard lamps flash four times along with an alarm indicating the attempt. If this occurs, press the “UNLOCK” button on the RKE to disarm the security alarm.

Using the ignition key to open the door, when the vehicle was locked and armed with RKE will be treated as unauthorized by the system setting off the alarm.

When vehicle is armed by RKE, opening the door from inside by operating the door inner handle will activate the vehicle theft alarm.

Press the unlock button on the RKE to cancel the alarm.

7.3.5 Back Door Open

Press the back door open button on the RKE to unlock the back door. The hazard lamps flash four times indicating the same.

7.3.6 Search Function

The search function can be used to locate the vehicle in a parking lot. Press the unlock button on the RKE for more than 3 sec. continuously to activate the search function.

When the Search function is ON, the hazard lamps flash for approx. 30 sec. helping you to locate your vehicle. To extend the search, press the search button again which will flash the hazard lamps for another 30 sec. You can turn it OFF by pressing the unlock button.

The head lamps also turn ON when UNLOCK button is pressed twice (enabling the LMV feature). For the first UNLOCK command, the doors are unlocked, and for the next UNLOCK command, the head lamps turn ON enabling you to safely board/locate the vehicle in the night.

Search function works both during Locked/Unlocked conditions of the vehicle.

7.3.7 Mute/Un-mute the Alarm/Beeps

The alarm or beeps heard when one of the doors are open can be muted/un-muted. Press the lock button for more than 3 sec. to swap between mute and un-mute.

The beeps heard during the door open situation can be muted/unmuted. There are NO BEEPS during normal locking/unlocking of doors.

7.3.8 Panic Alarm Function

The panic alarm function can be used during emergencies to draw the attention of onlookers/bystanders. Press the unlock button on the RKE for more than 3 sec. continuously when the key is in the ignition to activate the panic alarm.

7.3.9 Auto Locking

When the vehicle crosses 20 kmph road speed range with all the doors closed properly, all doors are locked automatically.

7.3.10 Auto Unlocking

All the doors are unlocked automatically, when the vehicle has halted and ignition switched OFF. If the ignition is not switched ON for the next few seconds, all the doors are locked due to auto locking, provided doors are not open.

7.3.11 Auto Re-locking

Once you press the unlock button on the RKE, if you do not open any of the doors for the next 45 sec., all the doors are re-locked automatically.

In case of an accident/collision where a SRS has been activated (Eg. airbag), all the doors are unlocked automatically.

7.3.12 RKE Operating Range

Using RKE, you can lock/arm or unlock/disarm the vehicle from distances approx. 30ft.(9m).

If there is reduction in RKE range, please follow the steps below:

• Check the distance: The RKE may be too far from the vehicle. Stand closer to the vehicle during rain or bad weather
• Check the location: Other vehicles or objects may be blocking the signals. Take a few steps to the left or right, hold the RKE higher, and try again. Moreover, closeness to a radio transmitter such as radio station tower, airport transmitter, mobile or CB radios may lead to reduction in range of RKE
• Check the RKE battery: See battery replacement procedure, given later in this section
• If the RKE is still not working correctly, contact an Authorized Mahindra Dealer

7.3.13 RKE Battery Replacement

If the RKE operation is inconsistent when any of the buttons are pressed it indicates that the RKE battery is weak. The rear side of the RKE is snap fitted. Using a small screw driver or similar tool, pry or separate the two halves of the casing.

Pull out the batteries and discard the same. Insert new batteries of 3V type. While fitting the new battery, ensure the positive side of the batteries face up. Align both the halves of the RKE and press to snap fit. Check operation of the RKE.

While prying the RKE case, take care not to damage the battery. Do not touch the battery terminals or contacts.

Do not mix old batteries with new batteries. Replace BOTH the batteries when the RKE operation is weak.

Perchlorate material needs special handling and disposal. Refer to local regulations.

7.3.14 If RKE is Lost

If you have lost the programmed RKE, contact an Authorized Mahindra Dealer for procuring a new RKE.

While programming a new key set, you will have to submit all the keys available with you, to an Authorized Mahindra Dealer.

Please note that there is a limitation (max 2 keys at a time) to the number of keys that can be ordered. The minimum time frame required to supply the duplicate keys is 10 days after all the formalities are completed. Please contact the dealer to understand the formalities involved.

If you make your own duplicate key, you will not be able to deactivate the anti-theft devices or start the engine.

If the key is stolen or lost, communicate to Authorized Mahindra Dealer for de-activating the function of the lost or stolen key. This is essential to avoid unauthorized access using the misplaced key.

Only RKE transmitters programmed to your vehicle electronics can be used for remote locking and unlocking of your vehicle.

7.4 Passive Keyless Entry (Smart key) / Smart Key System (if equipped)

Passive Keyless Entry (Smart key) System enables you to enter or exit your vehicle without the need to manually lock/unlock the doors. You can start/stop, lock or unlock the vehicle using Smart key. To do this, you only need carry the Smart key with you.

A	Unlock Button	C	Back Door Release Button
B	Emergency Key Release Button	D	Lock Button

NOTICE

RKE Panic alarm feature is not available in Smart Key variants.

The front side of the Smart key has three control buttons; Unlock (A), Lock (D) and Back door release (C) buttons. There is also a emergency key release button (B), which releases a mechanical key for emergency purposes (Eg. when PKE battery is low). To remove the metal key, press and hold the release button (B) and pull the mechanical key out.

NOTICE

• When locking or unlocking with Smart key, the distance between the Smart key and the corresponding door handle must not be greater than 3ft (1 m).
• Do not cover the key grip with any material that cuts off RF waves
• Do not leave the key exposed to high temperatures for a long period, such as on the dashboard or hood under direct sunlight
• Do not put the key in any liquid or wash it in an ultrasonic washer
• The Smart key can malfunction if exposed to moisture or static electricity

Carrying the smart key along with you, you can lock or unlock the doors and tail door and even start and stop the engine without inserting the key. Functions of the buttons on a smart key is similar to the remote key less entry.

Locking the vehicle:

1. Carry the smart key
2. Close all the doors
3. Press the button in the door handle

4. The hazard warning lights will blink once to indicate the locking (5 blinks will be provided if engine hood is open while locking)
5. Make sure that the doors are locked by pulling at the outside door handles

NOTICE

• Key should be in the proximity of less than 0.7m from the outside door handle
• Vehicle can be locked centrally by pressing the button in the door handle nearer to the PKE (PKE should be nearer to the triggered side). For Eg., locking/unlocking of the co-driver door is possible only if PKE is around the co-driver area.
• Even after pressing the outside door handle button, if the doors do not lock, a chime is heard along with the hazard blinking for 3 times, then one of the following situations are true;
– A smart key is kept inside the vehicle – The vehicle is in IGN ON or ACC ON position – One of the doors not closed properly
• On attempting to lock by pressing the button in door handle, the chime will sound for 3 times along with hazard lamp blinking 3 times if the steering is not locked
• With the one smart key inside, on locking the vehicle using the remote lock button, the key which is kept inside would get deactivated completely for the security of the vehicle. In order to make the key to active again, the vehicle should be unlocked either using smart key or by pressing remote unlock

Unlocking the vehicle:

1. Carry the smart key
2. Press the button in the door handle
3. All doors would unlock and hazard warning lights will blink twice

NOTICE

• Key should be in the proximity of less than 0.7m from the outside door handle
• Vehicle can be unlocked centrally by pressing the button in the door handle only when the key is in same side of the door where the button is pressed

Unlocking the Tail door alone:

1. Carry the smart key
2. Press the trunk release button in the tail door and pull the tail door

3. Tail door would unlock and hazard warning lights will blink 3 times
4. On closing the door, tail door would get locked automatically

NOTICE

• Key should be in the proximity of less than 0.7m from the outside door handle
• Tail door can be unlocked by pressing the button in the tail door only when the key is in range from the tail door
• Once tail door is closed, it can be unlocked for 45 sec without the key. So be cautious to lock the vehicle again if you are leaving the vehicle immediately

Mute/Un-mute the Alarm/Beeps

The alarm or beeps heard when one of the doors are open can be muted/un-muted. Press the lock button for more than 3 sec. to swap between mute and un-mute.

NOTICE

Only the door open beeps and alarm can be muted. The PKE alerts cannot be muted.

The system is automatically activated when the key is removed from the ignition.

7.4.1 Engine START/STOP Button

The engine can be started or stopped by the presence of the smart key inside the vehicle.

Whenever the doors are opened or the door handle button is pressed, the engine start/stop button will be illuminated and go off after few seconds.

Upon any fault identification by the system in the start stop switch, an alert would be provided in the Infotainment system along with a chime for 10 sec. Please visit the nearest Authorized Dealer immediately to rectify the problem.

Even with the failure in the start stop switch, vehicle normal function may work which depends on the severity of the failure. Please visit the nearest Mahindra Authorized Dealer to rectify the problem immediately.

To operate the engine start stop switch to its intended function, smart key should be inside the vehicle.

To turn off the engine, stop the vehicle and press the engine start stop button once. Status LED in the engine start stop button goes OFF to indicate the OFF position.

If the engine is not switching off by pressing the engine start/stop button (one press), press and hold the engine start/stop button for more than 2 seconds or rapidly press and release the engine start/stop button 3 times within 3 seconds. On doing so, the vehicle ignition status is changed to ACC position till 30 seconds then it will change to OFF position. In this condition, the vehicle can be locked using the PKE only after 30 seconds. However you can still lock the vehicle using the mechanical key. Contact the nearest Authorised Mahindra Dealer at the earliest.

Your vehicle is equipped with electronic anti-theft steering column lock. The steering wheel locks when the engine start stop button is in OFF position to protect against the theft. The steering wheel locks automatically when the driver door is opened or 30 sec after engine start stop button changes to OFF position. If the steering wheel is not locked properly when you open the driver door and on attempting to lock the vehicle, a warning chirp along with the hazard blinks thrice. Try locking the steering wheel again (by toggling Engine Start/Stop button). If problem is not solved, we recommend to take the vehicle to nearest Mahindra Authorized Dealer immediately.

To switch ON the ignition, press the engine start stop button when the switch position is in OFF/ACC without depressing the brake pedal and with the smart key inside the vehicle. Status LED in the engine start stop button will turn Green to indicate the IGN ON position and the vehicle is ready for starting. Status LED colour would change to orange if the vehicle is not started within 30 sec, but the vehicle ignition remains in ON position.

Keeping the vehicle in ignition ON position for longer time without engine running, would drain the battery. Turn OFF the ignition if engine is not to be started.

Vehicle ignition would not turn to ON position on any of the following conditions;

• If the electronic steering lock is not getting unlocked
– A warning would be displayed in the Infotainment system along with beep sound for few sec. If the steering wheel doesn’t unlock properly, press the start/stop button while turning the steering wheel right/left to release the tension on the lock.


Still if you are not able to turn ON the IGN, please contact the nearest Authorised Mahindra Service Centre.

• If the key is not detected inside the vehicle or far away from the driver which is not in detectable position


– A warning would be displayed in the infotainment system along with a beep sound for few sec. Bring the smart key inside the vehicle if not in the vehicle or keep the key away from any electronics gadgets to allow the system to detect the key
– If still the key is not detected, the key battery might be low. Press the start/stop button once and while the status LED in the button is blinking green, bring the key fob on top of the start stop button and hold for few seconds till status LED changes to permanent green. Once start/stop status LED turns Green, press Start/Stop button to turn ON IGN immediately


• When the engine start/stop button is in ON or engine running condition with vehicle stand still or in ACC position, and if any door is opened, the system checks for the smart key. If the smart key is not in the vehicle, an alert in Infotainment screen is displayed along with a chirp for 5 times to indicate key not detected inside


Bring the smart key inside the vehicle or keep the key in the detectable position whenever you are inside the vehicle.

Starting the vehicle

To start the engine, press the brake and press the engine start/stop button once with the key inside the vehicle. The engine can be started from any position (OFF/ ACC / ON) of the start/stop switch.

Ensure the gear lever is in park or neutral position before starting.
If Engine start/stop button is pressed without pressing the brake pedal, engine will not start and the vehicle power modes will change as follows; OFF -> ON -> OFF -> ON
If the engine start/stop button is pressed from the OFF position directly, along with the brake in depressed position, there may be a small delay in the engine cranking. This is normal and not to be taken as a fault.

Never press the engine start/stop button while the vehicle is in motion except in an emergency. This will result in the engine turning off and loss of power assist for the steering and brake systems. This may lead to loss of direction control and braking function, leading to an accident.
Once the engine is started, it would not stop even if the key is not inside the vehicle. Before leaving the driver seat, always make sure engine start/stop button is in OFF position and always take the smart key with you. Vehicle safety and security would be affected if these precautions are not followed.
In case of any failure in brake switch, engine can be started by pressing the start/stop button continuously for 10 seconds without depressing the brake pedal.

To turn the engine OFF in an emergency, press and hold the engine start/stop button for more than 2 seconds or rapidly press and release the engine start/stop button 3 times within 3 seconds. On doing so, the vehicle ignition is changed to ACC position.

If the vehicle need to be restarted while in motion, press the brake and start/stop button after shifting to N position.

If the key fob battery is low, the key may not be detected. In such a situation, press the start/stop button once while the status LED in the button is blinking green, bring the key fob on top of the start/stop button and hold it there for few seconds till status LED changes to permanent green. Once start/stop status LED turns Green, press start/stop button to turn ON IGN immediately.

If key fob battery is detected low by the system, an alert would be triggered while turning OFF the ignition. Change the battery by following the procedure as mentioned in the section for battery replacement.

Key fob battery low can be detected only if the key has been continuously used in the vehicle. Keeping the key outside the vehicle for longer duration and then using it with the drained battery cannot be detected.

7.4.2 Vehicle locking/Unlocking in an Emergency Situation

If the smart key does not operate normally, you can lock or unlock the doors by using the mechanical key.

1. To remove the mechanical key, press and hold the release button in the side of the key fob and pull the mechanical key head.
2. Insert the key into the key hole in the door nearer to the door handle. Turn the key towards the rear of the vehicle to unlock and turn it towards to front to lock.
3. To reinstall the mechanical key, put the key into the key fob and push it until a click is heard

It is strictly not advisable to leave the key fobs in the vehicle. Vehicle can be started by any unauthorized person.
A maximum of 2 smart keys can be registered to a single vehicle. If you loose a key, we strictly recommend to contact Mahindra Authorized Dealer immediately to block the lost key and to get a new key.

The smart key may not work if any of the following occur:

• The smart key is close to a radio station, airport or an area where there is a possibility of large radio transmissions which can interfere with the normal operation of the smart key
• The smart key is near a mobile or a cellular phone or some electronic gadgets like Laptop/Tablets. The signal from the smart key could be blocked by normal operation of your cell phone or smart phone. Avoid placing the smart key and your electronics gadgets in the same trouser or jacket pocket or in the bag and maintain adequate distance between the two devices
• Another vehicle smart key is being operated close to your vehicle
• Smart key kept inside the glove box or top bin in the instrument panel may not be get detected some times. Keep the smart key in the visible zone or in your pocket for getting it detected
• Keep the smart key away from the water or any liquid. If the keyless entry system is inoperative due to exposure to water or liquids, it will not be covered by your manufacturer’s vehicle warranty.

Make sure the vehicle ignition is in OFF state whenever leaving the vehicle even with the key. By keeping the vehicle ignition in ON/ACC state will hamper the vehicle security.
Do not hand over the smart key to any unauthorized person or service provider. Your vehicle security system may be compromised in doing so.

7.4.3 Smart Key Battery Replacement

If the Smart key operation is inconsistent when any of the buttons are pressed it indicates that the Smart key battery is weak. Follow the below procedure to change the battery in the Smart key.

While prying the old battery out, take care not to damage the Smart key housing.
Do not touch the battery terminals or contacts by hand.
Using the wrong battery can cause the Smart key to malfunction. Be sure to use the correct battery
An inappropriately disposed battery can be harmful to the environment and human health. Dispose the battery accordingly to your local law(s) or regulations

7.4.4 If Smart key is Lost

If you have lost the programmed Smart key, contact an Authorized Mahindra Dealer for procuring a new Smart key.

While programming a new key set, you will have to submit all the keys available with you, to an Authorized Mahindra Dealer.

Please note that there is a limitation (max 2 keys at a time) to the number of keys that can be ordered. The minimum time frame required to supply the duplicate keys is 10 days after all the formalities are completed. Please contact the dealer to understand the formalities involved.
If you make your own duplicate key, you will not be able to deactivate the anti-theft devices or start the engine.
If the key is stolen or lost, communicate to Authorized Mahindra Dealer for de-activating the function of the lost or stolen key. This is essential to avoid unauthorized access using the misplaced key.
Only Smart key transmitters programmed to your vehicle electronics can be used for remote locking and unlocking of your vehicle.

7.5 Engine Immobilizer System

An Engine Immobilizer System is a security system that prevents the vehicle being operated by an unauthorized person. The Engine immobilizer prevents the engine from being started unless it recognizes signals from the correct coded key. When a wrong key is inserted or a theft attempt is detected, the alarm is set off, and the hazard lamps flash along with a siren.

The system is automatically activated when the key is removed from the ignition.

Features of the Immobilizer System:

• Prevents the vehicle being started by anyone not in possession of the correct vehicle key
• The vehicle is automatically protected after the key is removed from the ignition. At every ignition ON, if the vehicle does not recognize the correct key code, the engine check lamp will be illuminate/blink and the engine cannot be started
• The vehicle will not be protected until the key has been taken out of the ignition

If the engine check lamp flashes or remains continuously illuminated after the ignition being switched ON, there is a system malfunction. Contact an Authorized Mahindra Dealer immediately.

Inserting the correct coded key in the ignition and switching the ignition ON, automatically deactivates the system. This enables the engine to start.

In the event of the vehicle not starting with the correct key, switch off the ignition for a minimum of 1 minute and attempt to start the vehicle again.

Do not modify, remove or disassemble the engine immobilizer system. Any unauthorized changes or modifications can affect proper operation of the system and will void your warranty.

The security system will be activated only when the vehicle is locked using the RKE. Locking the doors with the manual key will not activate the security system. Using the ignition key to open the door, when the vehicle was locked and armed with RKE will be treated as unauthorized by the system setting off the alarm. Press the unlock button on the RKE to cancel the alarm.

8 FEATURES AND CONTROL

8.1 Quadruple Switch

The quadruple power window switch on the driver door armrest/handle controls the following functions;

• Both LH and RH ORVM folding
• ORVM selector
• ORVM adjustment
• Power window functions of all doors in the vehicle.
• Power window safety switch that enables/disables power window operation of other doors when operated independently from the respective doors

8.1.1 Power Windows

Power windows can be operated only when the ignition is “ON” position. The driver can operate all the power windows in the vehicle through the quadruple switch on the driver door armrest/handle. Other passengers in the vehicle can raise or lower their respective window glasses individually by using the separate switches provided on each of the door trim pads/arm rests.

To lower/raise the window glass push/pull the power window switches respectively.

Do not operate the power windows frequently when the engine is OFF. This will drain the vehicle battery.

If you operate the switches often during a short period of time, the system might become inoperable for a certain duration to prevent damage due to overheating. The system will return to normal functioning shortly. It is recommended to operate one window switch at a time.

While operating the power windows, check for obstructions like head, hand, etc. which may lead to personal injuries.

Power Window Control after IGN OFF — The power window control will be available for 30 s after IGNOFF condition.

8.1.2 Power Window Lock Switch

The main power window quadruple switch in the driver door trim has a power window lock switch to enable or disable operation of rear passenger and front passenger window switches. To disable the rear or front passenger power windows, press the window lock switch down. To revert to normal operation, press the window lock switch again.

8.1.3 Auto/Express DOWN (driver side only)(if equipped)

Press the driver power window switch down for a moment and release. The glass moves all the way down automatically. You do not need to hold the switch till the glass comes down.

8.1.4 Auto Express Up Window(driver side only)(if equipped)

Pull the driver side power window switch up for a moment and release. The glass moves all the way up automatically. You do not need to hold the switch.

The driver side power window is equipped with anti-pinch, however please do not insert your finger during express up as it may result in injury.

If power window anti-pinch is used continuously for 15 times, the power window express feature will go to de-initialization mode.
In case of de-initialization, re-calibration or re-initialization of the power window needs to be done.

Re-initialization/Re-calibration of Power Window

Operate the window glass to top most position and hold the power window switch for 200 ms (minimum). Then, operate the power window to bring the glass to fully down position.

Same procedure of re-initialization/re-calibration to be followed in case of express feature not working due to battery removal/power failure.

8.2 Mirrors

8.2.1 Manual ORVM (if equipped)

Integrated exterior rear view mirrors on both the sides facilitate maximum rear view information to the driver.

Fold both the ORVM’s manually while parking the vehicle in congested roads or narrow parking slots. This avoids hindrances and safeguards the ORVM’s.

8.2.2 Electric ORVM (if equipped)

The ORVM fold switch, ORVM adjustment switch (perimeter switch) and the Left (L)/Right (R) ORVM selector switches are located on the driver door trim/handle.

Both the ORVM’s can be electrically folded or unfolded by the pressing the ORVM fold button (A).

All ORVM controls work only when ignition is ON or engine is in running condition.

The ORVM folding/unfolding operation is limited to 2 times / minute.

The electric ORVM’s fold automatically when the vehicle is locked through RKE or unlocked through RKE and ignition switched ON.

Do not overestimate the distance of the objects that you see in the mirrors. Objects seen in convex mirrors are much closer than they appear.

Use the ORVM L/R selector switch, to select Left/Right side exterior mirror respectively. The ORVM adjustment switch adjusts the selected ORVM in the required direction. Lock the ORVM’s by setting the ORVM selector switch to the middle position.

8.2.3 Interior Mirrors

There are two interior mirrors, one is a conversation mirror (fish eye type) and other interior rear view mirror.

8.2.4 Conversation Mirror (if equipped)

The conversation mirror can be used to converse with the rear passengers in the vehicle. Press the mirror cover to lower the conversation mirror. Close the mirror back and press to lock the mirror in position.

8.2.5 Interior Rear View Mirror

The interior rear view mirror provides the rear view information to the driver and also aids during reversing.

This mirror has day and night (anti-glare) positions. The night position reduces glare from head lamps of vehicles behind you. Flip the tab (A) on the bottom edge of the mirror to select the day or night position.

8.3 Sun Visor

Sun Visors are provided for both driver and co-driver above the windshield. The sun visors can be used for either frontal or sideward shade, to reduce glare or to shut out direct rays of the sun.

Pull down the sun visor to block the glare of the sun. The sun visor can also be swivelled to the side as shown.

The vanity mirror lamp will remain ON as long as the mirror flap/cover is open. This may lead to battery drain if left unchecked for long durations. Ensure the mirror flap/cover is always closed properly before folding back the sun visor in its position.

8.4 Utility Holders

8.4.1 Upper Console Tray

Do not place large or heavy objects on the foldable trays, accessing the centre console storage will be difficult. Ensure the tray cover is latched properly once closed.

Unlock the console tray cover by unlocking the tray latch (A) and lifting the cover all the way up.

8.4.3 Multi-box Storage

The multi-box is located above the infotainment screen in the centre console. It can be used for storing small items like mobiles, wallets, tickets, etc.

To open the lid, gently press the lid. To close, gently press the lid all the way down till it locks.

Do not store big items in the multi-box which may obstruct the proper closure of the multi-box lid. On rough or uneven roads, the lid might open up spilling the contents and leading to distraction.

8.4.4 Centre Box

The centre box is located below the HVAC/Switch bank near the gear lever. Small objects like tickets, wallet, etc., can be stored. To open, gently press the centre box lid. To close, gently press the lid all the way down till it locks.

8.4.5 Glove Box

There are two glove boxes on the co-driver side of the instrument panel.

• Upper Glove Box
• Lower Glove Box

The upper glove box can be opened by gently pressing the unlock push button (A). To close, gently lower the glove box lid and press to lock.

Do not overload the glove box.

Do not store loose or small metal objects inside glove box. This will lead to rattling while the vehicle is driven on bad roads.

The lower glove box is located just below the upper glove box. To open, gently press the unlock push button, and lower the lid. To close the glove box, raise the lid all the way up and gently press to lock the lid.

The lower glove box is illuminated automatically when it is opened and the light turns OFF when it is closed.

It is suggested to keep copies of all vehicle documents along with the owner’s manual kit in the glove box for reference when needed.

To avoid the possibility of injury in case of an accident or a sudden stop, both the upper and lower glove box lids should be kept closed when the vehicle is in motion.

8.4.6 Cup Holder

The cup holder located in the floor console between the front seats, It can be used for small cups or cans that are closed or have a lid.

Only sealed cups/cans with lid to be used in the cup holders.

Use caution when using the cup holders. A spilled beverage that is very hot can injure driver or passengers. Spilled liquids can also damage interior trim and electrical components. Any spilled beverage can also startle the driver and cause a loss of control of the vehicle resulting in an accident.

8.4.7 Ash Tray (if equipped)

An ash tray is provided in the cup holder. Lift the lid to use the ash tray. To empty the ash tray, firmly pull the ash tray up. Similarly, to put it back, gently press the ash tray back in the same location.

Do not use the ashtray for disposing of waste paper or other combustible items. They may catch fire when a cigarette butt is extinguished in the ash tray.

8.4.8 Second Row Seat Arm Rest — Cup Holder (if equipped)

The second rows seats have an armrest embedded into the seat back. The arm rest can be unfolded and used as a cup holder.

Only sealed or cups with lid and cans to be used in the cup holders.

Use caution when using the cup holders. A spilled beverage that is very hot can injure the passengers and damage interior trim. Never place objects other than cups or cans in the cup holder. These objects can be thrown out in the event of a sudden stop or an accident, possibly injuring the passengers in the vehicle.

8.4.9 Second Row Seat Arm Rest — Storage Bin (if equipped)

The second rows seats have an armrest embedded into the seat back. The arm rest incorporates a storage bin with smooth operating magnetic bin cover and a cup holder.

Only sealed or cups with lid and cans to be used in the cup holders.

Use caution when using the cup holders. A spilled beverage that is very hot can injure the passengers. Spilled liquids can also damage interior trim. Never place objects other than cups or cans in the cup holder. These objects can be thrown out in the event of a sudden stop or an accident, possibly injuring the passengers in the vehicle.

8.4.10 Third Row Cup Holder

The cup holders are located on both left and right side trims below the magazine holder.

Only sealed or cups with lid and cans to be used in the cup holders.

8.4.11 Bottle and Umbrella Holder

Bottle and Umbrella holders are located on both the front door lower trims. You can use them to store umbrellas, maps, papers, small books, bottles, etc.

NOTICE

Only sealed/closed bottles are to be used in the bottle holders.

8.4.12 Seat Back/Magazine Pocket

The seat back pockets are located on the back of the front seats for holding light weight papers/books/magazines, etc.

CAUTION

To avoid injury, do not place large or hard objects in the seat back pockets. Do not put more than 1 Kg weight in seat back pockets.

8.4.13 Third Row Magazine Pocket

The third row magazine pockets are located on the trims on either side of the third row seats. They can be used for holding light weight papers/books/magazines, etc.

CAUTION

Do not place large or hard objects in the magazine pockets. Do not put heavy objects in the magazine pockets.

There are two ticket, mobile or small object holders on either side of the front floor console.

8.4.14 Grip Handle

Foldable grip handles are provided above the front (passenger only), second row and third row outboard seats.

8.4.15 Coat Hook

The second row outboard passenger seats grip handles feature a coat hook for hanging your coat, shirts, etc.

NOTICE

Hang light weight articles only. Hanging excess/bulky weight/items may cause breakage of the hook and inconvenience to the passengers.

8.4.16 Sun Glass Holder

Roof mounted sun glass holder is integral part of the front interior lamp. Press the lid to release the latch and lower the holder. It is strategically positioned to be accessed easily by both the driver and front passenger.

CAUTION

Do not access the sun glass holder while you are driving. It may distract your concentration and could lead to an accident.

8.4.17 Floor Mat (if equipped)

Floor mats are provided in the front and rear foot wells to avoid stains on the floor carpet.

WARNING

Always keep the floor mats in their correct position to avoid interference with the movement of the accelerator or brake pedals during driving, which may lead to accidents.

8.5 Horn

Press the pad on the steering wheel to blow/sound the horn. The horn functions even when the ignition has been switched OFF.

8.5 Interior Lamps

Interior lamps comprise of front/rear roof lamps, map reading lamps, ambience lamps and ignition key ring illumination. These lamps can be used for an illuminated entry. In auto mode, the roof lamps (courtesy lamps) and ignition key ring illuminate when any of the doors are opened. Once all doors are closed, the interior lamps switch OFF.

8.6.1 Front Roof Lamp

The front roof lamp is located above the interior rear view mirror. The roof lamp can be switched ON by the switch on the lamp.

8.6.2 Map Reading Lamp (if equipped)

Do not leave the roof/map reading lamp in permanent ON mode. This will drain your vehicle battery.

8.6.3 Second Row Roof Lamp

The second row roof lamp is located on the roof above the second row seats. The courtesy lamp can be switched ON/OFF by the switch on the lamp.

The roof lamp switch has three operation modes to choose from

1. The roof lamp remains permanently ON in this position irrespective of the door open status
2. The roof lamp remains in DOOR/AUTO mode in this position.
3. The roof lamp remains permanently OFF in this position

The roof lamp remains permanently ON in this position irrespective of the door open status

The roof lamp remains in DOOR/AUTO mode in this position.

The roof lamp remains permanently OFF in this position

The operation of the roof lamp in door mode is as follows:

• Roof lamp switches ON, dims and goes OFF after 10 sec delay during RKE unlock
• Roof lamp switches ON when any of the doors is/are open
• Roof lamp dims and goes OFF after 10 sec delay upon closing of all doors
• Roof lamp dims and goes OFF immediately on RKE lock after all doors are closed
• If any of the doors are not closed properly, the roof lamp switches OFF automatically after a preset duration
• Roof lamp goes OFF with ignition ON and all doors closed properly

The roof lamp will be turned ON in the case of an accident in a SRS equipped variant provided the roof lamp switch is in “Door” mode.

8.6.4 Ambience Lamp (Icy Blue) (if equipped)

The ambience lamps give out a light red ambience in the vehicle. They can be switched ON/OFF by the ambience button on the centre bezel switch bank.

Ambience lamps are located in the following locations

• Around the front roof lamp

• Under the seat

• Above the pedals in the driver side foot well

• Below the door handle
• Above the bottle holder in the inner door trim

8.6.5 Door Ajar Lamp (if equipped)

The door ajar lamp is present on all four doors. The respective door lamp illuminates when that particular door is open or improperly locked.

The door ajar lamp illuminates even in the vehicle switched OFF condition with the ignition key removed.

8.6.6 Illuminated Scuff Plates (if equipped)

The illuminated scuff plates are switched ON every time the door is opened. This can also be used as a guide light during ingress or egress.

Camping Lamp (if equipped)

Camping lamp aids you during brief stops in night trips and also while loading/unloading luggage in the rear. It is switched ON/OFF by pressing the switch (A) on the camp lamp.

8.7 Power Outlet

There are three (depends on the variant) 12V power supply sockets provided for power take OFF. Electrical equipment/appliances like mobile phone charger, cigarette lighter, etc. can be used in the outlets.

The power sockets function only when the ignition is in ACC or ON positions. It is recommended to use the power sockets when the engine is ON to avoid battery drain.

The power outlets are located in the following places in the vehicle

• Front - In the compartment below the centre bezel switch bank.

• Second Row - Behind the centre console storage (if equipped)

• Third Row - Below the manual fuel lid open knob (if equipped)

To avoid serious injury:

• Close the power outlet cap when not in use
• Do not allow children to use or play with the power outlet
• When using electrical appliances, strictly follow the manufacturers instruction manual
• Never use the power outlet for electric heaters while sleeping
• Never insert foreign objects into the power outlet
• Never use malfunctioning electrical appliances
• Never insert inappropriate or badly fitting plugs into the power outlet

Do not modify, disassemble or repair the power outlet in any way. Doing so may result in unexpected malfunction or fire, which could cause serious damage to equipment and/or personal injuries. Contact an Authorized Mahindra Dealer for any necessary repairs.

To prevent injuries and accidents, secure all electrical appliances before use. Do not use any appliance that may:

• Distract the driver while driving, or hamper safe driving
• Result in a fire or burn injuries due to the appliance rolling, falling or overheating
• Emit steam, while the windows of the passenger compartment are closed

• Use the power outlets only when the engine is running. Remove the plug from the power outlet after using the electric device. Using the power outlets when the engine is OFF or leaving the electric device plugged in for many hours may cause the battery to drain
• Do not use the power outlet to connect electric accessories or equipment that are not designed to operate on 12V
• Some electronic devices can cause electronic interference when plugged into the power outlet. These devices may cause excessive audio noise and may interfere with other electronic systems or devices in your vehicle

8.8 Instrument Panel Illumination

The instrument panel light intensity can be varied by the illumination control knob located on the RHS near the head lamp levelling switch.
Roll up/down for bright/dim intensity of illumination for the following lighting:

• Instrument cluster
• Ambient lamp
• Interior switches
• Infotainment screen/display

8.9 AUX and USB Ports

The AUX and USB ports are provided on the centre switch bezel below the infotainment controls. They can be used as an input to the music system. You can connect ipods, USB memory sticks, etc., as an input and listen to the music through the vehicle speakers.

It is recommended to connect an input device only when the vehicle is stationary. Trying to connect an input device while driving may distract your attention and lead to accidents.

8.10 Exterior Lamps

8.10.1 Lighting Control Stalk

The lighting control stalk is located on the right hand side of the steering wheel and is a part of the combination switch. It controls operations of parking lamps, head lamps, head lamp beam selection, high beam flashing, front/rear fog lamps and turn signals when the ignition switch is ON.

8.10.2 Turn Signals

8.10.3 Turn Signal - Right

• Push the lighting control stalk clockwise (to stop position B) to indicate a right turn. The instrument cluster arrow lamp pointing towards the right flashes along with the right side turn signal lamps (front, rear & ORVM) with chime indicating your intention of turning towards right

After you have completed your right turn, the stalk will automatically return to the neutral position switching OFF all the lamps.

8.10.4 Taking a Left turn

• Push the lighting control stalk anti-clockwise (to stop position A) to indicate a left turn. The instrument cluster arrow lamp pointing towards the left flashes along with the left side turn signal lamps (front, rear & ORVM) with chime indicating your intention of turning towards left
• After you have completed your left turn, the stalk will automatically return to the neutral position switching OFF all the lamps.

If the turn signal lamps on the instrument panel flash faster than normal, there may be a possibility that one or more of the turn signal lamp bulbs have blown. Replace the blown bulb immediately.

8.10.5 Lane Changing

To signal a lane change, move the light control stalk clockwise or anti-clockwise to the limit point of free movement of the lever and release. The turn signals will flash three times and stop.
The turn signals will continue flashing as long as the lighting control stalk is held in the limit point of free movement.

8.10.6 Lamps OFF

Rotate the outer rotary switch on the lighting control stalk clockwise aligning the “arrow” on the stalk to “OFF” on the switch to switch OFF all lamps.

8.10.7 Parking Lamp ON

Rotate the outer rotary switch on the lighting control stalk clockwise aligning the “arrow” on the stalk to the “1st detente” position on the switch to switch ON the parking lamps.

The tail lamp, license plate lamp, instrument panel illumination lamps and all interior switches are also activated when the parking lamp is switched ON.

Park–On Reminder — When the Park Lamp is in ON condition and IGN is turned off, a chime will be triggered in instrument cluster to remind that the Park Lamp is ON.

Park/Position Lamps will not be switched off automatically. User has to turn it off manually.

8.10.8 Head Lamp ON

otate the outer rotary switch on the lighting control stalk clockwise aligning the “arrow” on the stalk to the “2nd detente” position on the switch to switch ON the head lamps.

Switch ON the head lamp, and push the lighting control stalk down (away) from steering wheel to switch ON the head lamp high beam or lift/pull the lighting control stalk up towards the steering wheel to switch ON the head lamp low beam. In head lamp high beam, the high beam telltale lamp in the instrument cluster illuminates indicating high beam option selected.

8.10.10 Head Lamp Flash

ull the lighting control stalk (from the head lamp low beam position) towards the steering wheel to instantaneously flash the head lamp high beam. The head lamp flash works only when the head lamp is OFF or in low beam position.

8.10.11 Auto Head Lamp

The auto head lamp feature works on the outside ambient light intensity input by the RLS (Rain-Light Sensor). Based on this input, the head lamps are turned ON/OFF. For Eg., this feature will be helpful while driving through a tunnel or poor lit area.

The RLS is located behind the interior rear view mirror on the windshield.

To turn ON the auto head lamp feature, rotate the outer rotary switch on the lighting control stalk anti-clockwise aligning the “arrow” on the stalk to the auto head lamp icon on the switch. This is indicated by the auto head lamp tell tale in the infotainment screen.

To de-activate the auto head lamp, rotate the outer rotary switch on the lighting control stalk clockwise aligning the “arrow” on the stalk to the OFF position on the switch.

There is a difference between ambient light intensity sensed by the RLS (Rain-Light Sensor) on the windshield and by the human eye. The RLS may activate the head lamps early during evening hours or may de-activate late during morning hours. This is absolutely a normal behavior.

In case of a windshield replacement, the RLS also needs to be replaced along with the windshield. An old RLS cannot be calibrated to a new windshield.

8.10.12 Head Lamp Levelling System

When the vehicle is either fully or partially loaded, it may have an upward inclination disturbing the head lamp aiming. A correct head lamp setting provides good visibility to the driver with minimum inconvenience to other road users.

To properly aim the head lamp beam, use the head lamp leveling switch. This switch is located on the right side of the steering column shroud in the instrument panel. This switch has four positions marked as 0, 1, 2 & 3.

Select the suitable switch position depending on the pay load as advised in the table.

The headlights can only be adjusted when the low beam is switched ON

8.10.13 Static Bending Lamp (if equipped)

Static Bending lamps are available on both the head lamps. The static bending lamp assists the driver while taking a turn. It will be activated when the head lamp is ON and steering wheel turned more than 90° at 5 kmph or 45° at 100 kmph speeds.

8.10.14 Fog Lamps (if equipped)

Fog lamps are to be used along with head lamp low beam, to improve the vision during foggy and misty conditions.

8.10.15 Fog Lamps OFF

Align the “OFF” of inner rotary switch on the lighting control stalk to the “arrow” mark on the inner fixed stalk as shown to switch OFF the fog lamps.

8.10.16 Front Fog Lamps ON

To switch ON the front fog lamps, first switch ON the parking lamps, rotate the inner rotary switch on the lighting control stalk anti-clockwise aligning the front fog lamp icon to the “arrow” on the inner fixed stalk as shown. The rotary switch moves back to its neutral position once released.

The front fog lamp indicator in the instrument cluster indicates the operation status.

Fog lamps will turn ON only if parking lamp is ON.

8.10.17 Rear Fog Lamp

To switch ON the rear fog lamps, first switch ON the parking lamps, rotate the inner rotary switch on the lighting control stalk clockwise aligning the rear fog lamp icon to the “arrow” on the inner fixed stalk as shown. The rotary switch moves back to its neutral position once released.

he rear fog lamp indicator in the instrument cluster indicates the operation status.

Fog lamps will turn ON only if parking lamp is ON.

8.10.18 Puddle Lamp (if equipped)

Puddle lamps are provided at the bottom of the front and rear doors. They are switched ON automatically when either of the front or rear doors are opened. This illuminates the ground below the respective door thereby assisting in a safe entry and exit.

8.10.19 Entry Assist Lamp (if equipped)

Entry assist lamps are located on the bottom of both left and right ORVM’s. They provide a illumination outside the driver and front passenger doors when the FMH or LMV features are activated.

8.10.20 Logo Projection Lamp (if equipped)

Entry Assist Lamp logo projection lamps are located on the bottom of both left and right ORVM’s. They provide a illumination of the XUV500 logo outside the driver and front passenger doors as per the following logic;

Logo Projection Lamp — Operating Logic

• When the vehicle is unlocked either by remote or through passive entry in the night time, the ORVM unfolds and ‘XUV 500’ Logo projection lamp will be projected in the ground along with lead me to Vehicle function. The logo remains ON for 20seconds or till engine is started, whichever is earlier.
• The logo projection lamp is also switched ON when the engine is shut off in auto stop mode. The logo projection lamp remains ON for 20 seconds or till the engine is restarted, whichever is earlier.
• During exit, the ‘XUV 500’ Logo projection lamp will be projected in the ground along with follow me home function for 20 seconds. The mirror will fold after the logo lamp is switched OFF.

Activating the logo lamp and ORVM folding through remote repeatedly or unnecessarily may lead to

premature failure of ORVM folding function.

8.10.21 Follow-Me Home (FMH) (if equipped)

This feature helps the driver and passengers to easily get out of the vehicle during poor light conditions. The head lamp low beam and entry assist/logo projection lamps are turned ON for about 20 seconds assisting the passengers to find their way.

• Switch OFF the parking lamps
• Remove the ignition key
• Open the driver door
• Head lamp and entry assist lamp switches ON for 20 seconds unless cancelled by UNLOCK signal.

For FMH to be activated, the vehicle should have been driven with the park lamps or auto head lamp ON before switching OFF.

To extend the FMH feature further for 20 seconds, press RKE LOCK button. This FMH extension can be availed for maximum 2 minutes from the first activation.

With FMH mode ON; First LOCK signal received from RKE will lock the doors and subsequent LOCK signal is used to toggle the head lamp ON and OFF.

With FMH mode ON, if UNLOCK signal is received twice from RKE; the feature gets deactivated and cannot be extended further. Also, the doors are unlocked and vehicle disarmed.

8.10.22 Lead Me to Vehicle (LMV) (if equipped)

LMV is the feature that switches the head lamp and entry assist/logo projection lamps ON for 20 seconds helping the passengers to reach the parked vehicle safely and comfortably at night.

• Pressing the unlock button on the RKE under poor light conditions (if vehicle is equipped with auto head lamp)
• Pressing the unlock button on the RKE when FMH was activated while locking the vehicle previously (if vehicle is not equipped with auto head lamp)

• At the end of 20 seconds after activation
• When any door is opened
• Ignition is switched ON
• LOCK command is received from RKE

To extend the LMV feature further for 20 seconds, press RKE UNLOCK button. This LMV extension can be availed for maximum 2 minutes from the first activation.

With LMV mode ON; First UNLOCK signal received from RKE will unlock the doors and subsequent UNLOCK signal is used to toggle the head lamp ON and OFF.

8.10.23 Hazard Warning Lamp

The hazard warning lamp switch is located in the centre bezel switch bank on the instrument panel.

To turn the hazard warning lamp ON, push the switch in. All the turn signal lamps flash. The instrument cluster turn indicator lamps also flash indicating the same. To turn OFF, push the switch again.

Use the hazard warning lamp when your vehicle is stationary or to warn other road users to be cautious while passing your vehicle.

The turn lamps do not work when the hazard warning lamps are operational.

8.11 Windshield Wipers

8.11.1 Wiper Control Stalk

8.11.2 Wiper Off

The wipe function is OFF when the wiper control stalk is in neutral position (B).

8.11.3 Flick-Wipe (Mist)

Push the wipe control stalk to position (A) for a flick-wipe, hold to operate the wipe continuously (simultaneously lift the wiper stalk towards the steering wheel to operate the wash). The stalk automatically comes back to position (B) when released.

8.11.4 Intermittent (INT) Mode

Intermittent (INT) wiping is selected when the wipe control stalk is pushed down to position C. In the INT mode, the wiper operates on preset intervals.

The delay between each wipe can be varied by rotating the wiper speed intensity rotary switch (F).

8.11.5 Low Speed Wiping

Push the wipe control stalk down to the position (D) to operate the wiper at a fixed low speed.

8.11.6 High Speed Wiping

Push the wiper control stalk down to position (E) to operate the wiper at a fixed high speed.

The wipe/wash function can be activated only when the ignition is in “ON” position.

8.11.7 Auto Wipe

The auto wipe feature works by sensing water (by the RLS) on the windshield. Based on this input, the wipers are turned ON/OFF. For Eg., this feature will be helpful when the rain is inconsistent.

The RLS (Rain-Light Sensor) is located behind the interior rear view mirror on the windshield.

To turn ON the auto wipe feature, press the outer rotary switch side/edge on the wiper control stalk. This is indicated by the auto wipe tell tale in the infotainment screen and the wiper performing one single wipe.

The sensitivity of the RLS can be varied by the wiper speed intensity rotary switch (F) on the wiper stalk.

There is a difference between the RLS (Rain-Light Sensor) sensing rain (water) on the windshield and the human eye sensing rain. The RLS may activate the wipers when the windshield (top band) is wet. This is absolutely a normal behavior.

In case of a windshield replacement, the RLS also needs to be replaced along with the windshield. An old RLS cannot be calibrated to a new windshield.

8.11.8 Wipe/Wash

Pull/Lift the wiper control stalk towards the steering wheel from any position to activate wipe/wash function. Washer fluid from front washer reservoir is pumped and sprayed onto the windshield. The wipers wipe the windshield 3 times after the washer spray is stopped and wipe once after 5 sec. Hold the stalk in position for continuous spray of washer fluid.

When wiper is in OFF or Interval mode:
After completion of the wipe/wash cycle, wipers return to their bottom position.
If the wipers are in interval mode and DWELL delay is less than or equal to 5 seconds, then the wiper will continue in the interval mode.
If the wipers are in interval mode, and DWELL delay is more than 5 seconds, then a further single wipe will be performed 5 seconds after the wash/wipe cycle. After the drip wipe (last wipe), wiper returns to normal interval wipe.

8.11.9 Rear Wiper

Rotate the outer rotary switch on the wiper control stalk to align the “arrow” on the stalk to the rear wipe “ON” position to operate the rear wiper.

8.11.10 Rear Wash

The rear windshield wash & wipe operates 3 to 4 times or as long as the stalk end is turned/rotated to the rear wash position. Wiping will continue for few seconds after releasing the stalk end switch.

Using a windshield washer in freezing temperatures could be dangerous. The washer fluid could freeze on the windshield, and block your vision resulting in an accident. If you operate your vehicle in temperatures below 4°C, use washer fluid with antifreeze protection.

• Do not operate the wipers when the windshield is dry. It may lead to scratches on the glass
• It is recommended not to use the wiper when the windshield glass is covered with debris, snow or leaves. Clean the glass before using the wiper to avoid damage to the wiper blades and glass
• Do not operate the windshield washer for more than 10 seconds or when the reservoir is empty.

8.11.11 Auto-rear Wiping

With the front wipers ON and rear wipers OFF, engaging the reverse gear activates the rear wiper.

8.11.12 Windshield Washer - Front & Rear

There are two nozzles with three adjustable washer jets in the front (below the wipers). Using a pin, the eye ball jets can be adjusted precisely for direction. Always direct the washer jet to hit middle of the windshield. This will enable the wiper blade to wipe the complete width of the windshield.

In the rear, two nozzles with twin adjustable washer jets are provided for the rear windshield wash. Adjust the nozzle to direct the washer jet to hit the middle of rear windshield using a pin. Rear windshield washer fluid is supplied from rear washer reservoir located in the back door.

8.12 Electric Sunroof (if equipped)

A Sunroof will make the driving experience more enjoyable by bringing light and sunshine into the vehicle. It provides a real open air feeling along with pure driving fun. With fresh air, your driving experience automatically becomes significantly more relaxed. A sunroof allows air to flow evenly from above the driver, which is much quieter and less intrusive than wind blowing through a side window.

Press the sunroof control lever backward/open (B), both the sunshade and sunroof glass will slide all the way open. To stop the sunroof movement at any point, press the sunroof control glass lever (B) momentarily.

Press the sunroof glass control lever backward/open (B), the sunroof glass will slide all the way open. To stop the sunroof glass movement at any point, press the sunroof control lever (B) momentarily.

With the sunroof open, to close the sunroof glass press the sunroof glass control lever forward/close (A).

In cold and wet climates, the sunroof may not work properly due to freezing conditions.

After a vehicle is washed or in a rainstorm be sure to wipe off any water that is on the sunroof before operating it.

Tilt up — The sunroof is tilted up when the Sunroof Glass Control Lever —Forward/Close (A) is shortly pressed (in the sunroof closed condition).

Tilt down/close — The sunroof is tilted down/closed when the Sunroof Glass Control Lever —Backward/Open (B) is pressed (in the sunroof tiled up condition).

• Even though the sunroof can be operated when the ignition key is in the ON position (the engine is not running), operating the sunroof repeatedly with the engine turned off will run down the battery. Operate the sunroof while the engine is running
• When a desired sunroof operation is completed, release the switch. If you keep the switch operating, it could cause a malfunction. Especially in the winter, never operate the sunroof if moving areas are iced. Wait until the areas are deiced
• When leaving the vehicle unattended, be sure to completely close the sunroof. This may otherwise lead to risk of vehicle theft or, the interior of the vehicle getting wet when it rains or snows
• If there are children in the car: Close the sunroof securely and remove the key before leaving the vehicle.
• Ensure children do not stand on the “armrest” to lookout of the sunroof. The armrest is a movable part and may move causing injury/accident.
• Do not leave the sunshade closed while the sunroof is open.

To prevent any body parts from being trapped by the auto-closing sunroof, an Anti-Pinch Function automatically opens the sunroof when an object is trapped.

• The sunroof pinch protection function only operates during automatic closing, not manual closing
• When operating the sunroof, be aware of safety conditions before operation. Parts of the body can be trapped
• Never adjust the sunroof or sunshade while driving. This could result in loss of control and an accident that may cause death, serious injury, or property damage.
• Anti-pinch function is not available in sunroof “Tilt” close operation
• If you would like to carry items on the roof rack using a cross bar, do not operate the sunroof. When carrying cargo on the roof rack, do not load heavy items above the sunroof or glass roof.

When you drive the vehicle with the window or sunroof open at a certain position, you may feel some pressure upon your ears or hear some noises similar to those from a helicopter. This happens because of an influx in air through the window or sunroof and its resonance effect. If this happens, adjust by opening the window or sunroof.

• When the battery is disconnected/discharged the sunroof may malfunction, reset the system.

Battery Discharge/Disconnect or Power Failure while Operating Sunroof

f the sunroof is stopped midway due to a discharged battery or power failure or battery has been disconnected, you need to re-calibrate the starting point of the sunroof. In addition, the following cases need the re-calibration.

• The sunroof does not completely close or open by operating the switch once
• The sunroof slides back to close. But the operation does not stop even after a complete close and tilts up the sunroof
• The opening gap remarkably decreases for the sliding open or tilt up
• Operation of the sunroof switch does not do anything or work properly Re-Calibrating the Sunroof Starting Point
• Close the sunroof completely by using the Sunroof Glass Control Lever —Forward/Close (A). Release the lever
• Push the sunroof control lever forward/close in the direction of close (for about 10 seconds) until the sunroof moves a little. Then, release the lever
• Push the sunroof control lever forward/close in the direction of close, until the sunroof operates as follows; The sunshade and sunroof glass slide open → The sunroof glass slide close → The sunshade close
• Release the lever
• When this is completed, the sunroof system has been reset

When the sunroof is completely opened with the sunroof switch and the switch is operated to the “OPEN” direction for more than 5 seconds, the sunroof cannot completely be either closed or opened by operating the switch once. The sunroof will be moving only when the switch is being operated. When this happens, re-calibrate the beginning point of the sunroof to reactivate the one touch function.

Periodically remove any dirt that may accumulate on the guide rail. Close the sunroof when driving in dusty environments. Dust may cause a noise or malfunction of the system.

8.13 Instrument Cluster

The instrument cluster comprises of the tachometer, speedometer, trip meter (A & B), Reset Button, Odometer, Fuel gauge, Coolant Temperature gauge, Warning lamps and Telltale indicators.

8.13.1 Tachometer

The tachometer indicates the real time engine speed in thousands of RPM (revolutions per minute). Each division is 500 RPM. Running the engine in very high RPM leads to excessive engine wear and poor fuel economy. Maintain steady engine speed below 2500 RPM and do not accelerate or decelerate abruptly.

Do not over-accelerate the engine during idling, this can cause severe engine damage and would be treated as abuse of the engine which is not covered by warranty.

8.13.2 Speedometer

The speedometer indicates the real time road surface speed of the vehicle in kilometers per hour.

The vehicle speedometer is affected by size of the tires used. If the size of the tires are changed from those fitted at the factory, the speedometer might not display the correct road surface speed and distance travelled.

8.13.3 Odometer

The odometer records and displays the total distance traveled in kms. Press the reset button (A) to cycle through odometer and tripmeter displays. Odometer cannot be reset.

8.13.4 Tripmeter and Reset Button

Tripmeter displays the elapsed distance travelled since the last trip reset. There are two tripmeter’s (A/B) which can be reset individually as necessary.

Odometer and Tripmeter are displayed only when the ignition is ON and their displays are cycled/toggled by the reset button (A).

• To select trip A or B, press and release reset button (A) for a second
• To shift from trip A to trip B or vice versa, press and release the reset button (A) again for a second
• While on trip A or B, press and hold the reset button (A) for more than 1 second to reset the respective trip reading to zero\
• Pressing the reset button (A) while in trip B, displays the odometer reading. Again pressing the rest button (A) displays trip A

8.13.5 Engine Coolant Temperature Gauge

The engine coolant temperature gauge functions only when the ignition is switched ON. It indicates the instantaneous engine coolant temperature. The coolant temperature varies with changes in weather, load on engine and driving pattern. Temperature rises from Cold (C) (Blue color) to Hot (H) (Red Color).

When coolant temperature reaches the red zone, the high engine coolant temperature warning lamp illuminates.

In such situations switch OFF the AC and observe for any improvements in temperature gauge. If not, stop the vehicle and allow the engine to cool down. Check the coolant level in the coolant reservoir and top-up if required. If the engine is still heating up, contact your nearest Authorized Mahindra Dealer.

Never remove the radiator cap when the engine is hot. The engine coolant is under pressure and could splash on to skin/eyes causing severe burns. Wait for the engine to cool down before adding coolant to the reservoir.

Do not continue driving the vehicle with a overheated engine. This will lead to damage of engine components and engine seizure.

8.13.6 Fuel Level Gauge

The fuel level gauge functions only when the ignition is switched ON. It gives the status of the fuel level in the fuel tank. F indicates the tank is full (70 liters), E indicates the tank in empty.

When the fuel level reaches the reserve, the last 2 bars are displayed. The last bar in the display blinks when the fuel in the tank reaches the low level (approx. 5 liters).

The amount of fuel required to fill the tank up may be less than the specified tank capacity, as a small amount of reserve fuel always remains in the tank.

On inclines or curves, due to the movement of fuel in the tank, the fuel level may fluctuate or the last bar may flash earlier than usual. Always check the fuel level when the vehicle is on level road.

If the last bar flashes even after filling sufficient fuel, contact your Authorized Mahindra Dealer as soon as possible.

When all the bars in the display starts blinking/ flashing, contact the nearest Authorized Mahindra Dealer at the earliest.

8.14 Warning/Telltale Lamps in the Instrument Cluster

A	Parking Lamp	N	High Coolant Temperature Warning Lamp*
B	Seat Belt Warning Lamp	O	Low Engine Oil Pressure Warning Lamp**
C	AWD Lamp	P	ESC System Warning Lamp@
D	Left Turn Indicator	Q	ABS Warning Lamp*
E	Airbag Warning Lamp	R	ESC OFF Lamp@
F	Front Fog Lamp	S	Tiretronics*
G	Glow Plug Indicator	T	Check Engine Lamp**
H	Vehicle Armed Status Lamp	U	Parking Brake ON/Brake Fluid Low Warning Lamp
I	Rear Fog Lamp	V	OBD Check Lamp*
J	Low Fuel Warning Lamp	W	Head lamp High Beam Indicator
K	Water in Fuel Filter Warning Lamp*	X	Automatic Transmission Warning Lamp
L	Right Turn Indicator	Y	Charging System Warning Lamp**
M	Cruise Control Indicator@	Z	Door Ajar Warning Lamp
	@ if equipped
	** Come ON momentarily with ignition ON and will remain ON till engine is started.
	* Come ON momentarily with ignition ON and go OFF in few seconds.

8.14.1 Seat Belt Warning Lamp

The seat belt warning lamp illuminates reminding the driver to fasten the seat belt when the ignition is ON. The lamp will continue to illuminate till the driver fastens the seat belt properly.

8.14.2 Turn Lamps

The turn lamp arrows in the instrument cluster flash showing the direction indicated by the turn signals. A sudden increase in the rate of flashing indicates failure of one or more of the lamp bulbs. Have them replaced as soon as possible.

8.14.3 Airbag Warning Lamp

The airbag warning lamp in the instrument cluster illuminates when the ignition is switched ON and goes OFF in about 2 seconds once the engine is running. If the lamp remains ON continuously or flash’s intermittently, contact an authorized Mahindra dealer immediately.

Following conditions indicate airbag malfunction:

• Lamp fails to go OFF after engine is started
• Lamp does not illuminate at all
• Illuminates while driving

Contact an authorized Mahindra dealer immediately when the airbag warning lamp indicates a system malfunction. The airbag may not deploy when needed, which could result in serious or fatal injury, or it might deploy unexpectedly or unnecessarily, which may result in personal injury.

8.14.4 Front Fog Lamp (if equipped)

The front fog lamp telltale indicates the status of the front fog lamp. The front fog lamp can be switched ON only when the parking lamp is ON.

8.14.5 Low Fuel Warning Lamp

When the fuel level in the fuel tank falls below the reserve limit, the low fuel warning lamp is illuminated. Refuel sufficiently and the lamp goes out. If the lamp continues to remain ON even after refueling, contact an Authorized Mahindra Dealer.

8.14.6 Glow Plug Indicator

Glow plug indicator illuminates when the ignition is turned ON. It automatically goes OFF when the glow plug reaches the required temperature. Contact an Authorized Mahindra Dealer if the glow plug lamp does not illuminate with ignition ON or illuminates while driving.

8.14.7 Vehicle Armed Status Lamp

The vehicle armed status lamp flashes intermittently (few seconds frequency) once the ignition is switched OFF and the vehicle security system is armed (when locked using the RKE).

Fast blinking indicates a malfunction in the engine immobilizer system. Contact an Authorized Mahindra Dealer immediately.

8.14.8 Rear Fog Lamp (if equipped)

The rear fog lamp telltale indicates the status of the rear fog lamp. The rear fog lamp can be switched ON only when the front fog lamp is ON.

8.14.9 High Engine Coolant Temperature Warning Lamp

The high engine coolant temperature warning lamp flashes when the coolant temperature is above 105ºC. It starts to flash at double the rate when the temperature reaches 110ºC and will be continuously ON with buzzer alert when the temperature reaches 114ºC.

The “red” bars in the temperature gauge also flash in same frequency as the high temperature warning lamp when the above set temperature thresholds are reached.

CAUTION

Do not continue driving the vehicle with an overheated engine. This may result in engine damage, which will not be covered by the limited warranty.

8.14.10 Water-in-Fuel Warning Lamp

The water-in-fuel warning lamp illuminates when the accumulation of water in the fuel filter reaches the maximum permissible limit. The fuel filter needs to be drained. Contact an authorised Mahindra dealer.

CAUTION

Do not continue driving the vehicle with the water in fuel warning lamp ON. This may result in fuel pump/ other fuel system component damage, which will not be covered by the limited warranty.

8.14.11 Cruise Indicator

The cruise control lamp illuminates when the ignition is switched ON and goes off in about 2 seconds indicating normal status. The lamp blinks if the accelerator is depressed, while in cruise mode When SET+ button in the steering wheel is pressed, cruise control is activated and the lamp illuminates indicating the vehicle is in cruise mode.

When CRUISE OFF button in the steering wheel is pressed, the cruise mode is deactivated and the lamp goes OFF indicating that the vehicle is not in cruise mode.

If the lamp does not illuminate when the vehicle is in cruise mode or does not go OFF when the vehicle is out of cruise mode, there is a possible malfunction in the lamp or the cruise control system. Have the vehicle checked by an authorized Mahindra dealer.

8.14.12 Low Engine Oil Pressure Warning Lamp

The low engine oil pressure warning lamp illuminates when the ignition switch is turned ON goes out as soon as the engine is started. If the lamp remains ON even after starting the engine, or illuminates while driving, stop immediately, check the oil level after 2-3 minutes. If low, add engine oil to the “MAX” level and check status. If problem persists, contact an Authorized Mahindra Dealer immediately.

WARNING

Operating the vehicle with the low oil pressure warning lamp ON could cause sudden unexpected engine failure and loss of vehicle control, resulting in an accident and/or serious personal injury.

CAUTION

Do not run the engine with low oil pressure warning indicator ON. This may result in engine damage, which will not be covered by the limited warranty.

8.14.13 ESP System Warning Lamp

While driving, if the ESC system warning lamp blinks, it indicates that ESP has taken control of the vehicle stability. If the lamp remains ON, it indicates the malfunction in the ESP System. Contact the nearest Authorized Mahindra Dealer.

8.14.14 ESP OFF Lamp

The ESP OFF lamp illuminates when the ESP has been switched OFF manually.

8.14.15 Tiretronics

The Tiretronics lamp illuminates if there is a tyre pressure or temperature difference in one of the tires. The Tiretronics lamp blinks (for approx. 75 sec.) and then illuminates continuously when there is a malfunction in the Tiretronics.

8.14.16 Check Engine Lamp

The check engine lamp illuminates when the ignition is switched ON and goes out in 2 seconds indicating normal status. The lamp blinks or illuminates continuously if there is a fault in the engine management system. Switch OFF the engine immediately. Contact the nearest Mahindra dealer for necessary repairs.

8.14.17 Parking Brake Lamp

The lamp illuminates when; Parking brake is engaged or when brake fluid level is low or when front brake pads are worn. If the lamp illuminates while driving, do the following:

• Check if the parking brake is engaged. If yes, disengage it
• Check if brake fluid level is low. If yes, top-up brake fluid to the required level

If the brake lamp still continues to illuminate, immediately get the vehicle checked at an Authorized Mahindra Dealer.

WARNING

Clean the top of the brake fluid reservoir before removing the cap. Make sure no dirt, impurities or other items fall into the reservoir. Do not leave the cap off for more than a few minutes. Any contaminants, impurities or moisture in the brake fluid can affect brake operation, resulting in an accident.

WARNING

If the brake warning lamp comes ON while driving, the brake system might not be working properly. The pedal might be harder to operate or might go closer to the floor and it can take longer to stop. Pull off the road carefully and stop the vehicle. Have the vehicle towed to the nearest Authorized Mahindra Dealer for checks or repairs.

WARNING

Driving the vehicle with the brake warning lamp ON or when you suspect brake trouble is very dangerous and could result in serious injuries. Have your vehicle towed to an Authorized Mahindra Dealer.

8.14.18 OBD Check Lamp

The OBD check lamp illuminates when the ignition is switched ON and remains ON till the engine is started indicating normal status. If the lamp remains ON, it indicates a potential malfunction.

There may be a malfunction in:

• The fuel management system
• The emission control system
• Systems which affect emissions

Such malfunctions may result in excessive emissions. Contact an Authorized Mahindra Dealer immediately.

8.14.19 Head Lamp High Beam Lamp

The head lamp high beam telltale illuminates whenever the head lamps are switched ON to high beam or when the head lamp flash is used.

8.14.20 AT Malfunction Indicator Lamp

• This warning lamp comes on when the ignition switch is turned on and it goes off when the engine is started.
• If the lamp stays on or comes on while driving, some of the Transmission control components including sensors and devices may be malfunctioning.
• If the Indicator lamp is blinking continuously, reduce the vehicle speed until the lamp stops blinking. Contact the Mahindra dealer as soon as possible.

8.14.21 Anti-lock Brake System (ABS) Malfunction Lamp (if equipped)

The ABS malfunction lamp illuminates when the ignition is switched ON and goes OFF after about 2 seconds. If the ABS malfunction lamp continues to remain ON or illuminates while driving (and the brake system warning lamp is OFF), ABS will not operate. But the brake system will still operate conventionally. In this condition, the wheels can lock during severe braking. Have the vehicle checked by an authorized Mahindra dealer as soon as possible.

However, if ABS malfunction lamp and brake warning lamp are simultaneously glowing, there is a severe malfunction in the ABS. Operate the vehicle with extreme care and have the vehicle checked as soon as possible at an authorized Mahindra dealer.

8.14.22 Battery Charging System Warning Lamp

The battery charging system warning lamp illuminates when the battery is not being charged or when there is a malfunction in the alternator.

This lamp illuminates when the ignition is switched ON and goes out as soon as the engine is started. If the lamp continues to remain ON even after starting the engine, it is an indication that the battery is not being charged or there is a malfunction in the alternator. Check the alternator drive belt for looseness/breakage. If the drive belt is okay, switch OFF all unnecessary electrical equipment and recheck. Contact an Authorized Mahindra Dealer for further assistance.

8.14.23 Door Ajar Warning Lamp

The door ajar warning lamp illuminates and the buzzer chimes 3 times when any of the doors including the hood and back door are open during ignition ON. The lamp goes OFF when all the doors are closed properly.

8.15 Radio Frequency ID (RFID) Tag

Your vehicle is fitted with a RFID tag as per CMVR regulations on front windshield.

RFID tag may be used for Electronic Toll Collection (ETC).

NOTICE

Do not peel or remove the RFID.

9.1 Steering

Your vehicle is equipped with power steering. Power steering uses energy from the engine to decrease the driver's effort in steering the vehicle. The power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. If for some reason the power assist is interrupted, it will provide mechanical steering capability to steer the vehicle. Under these conditions, you will observe a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.

NOTICE

Upon initial start-up in cold weather, the power steering pump may produce noise for a short amount of time. This is due to the cold, thick fluid in the steering system. This noise should be considered normal, and it does not in any way damage the steering system.

WARNING

Continued operation with reduced power steering performance could pose a safety risk to yourself and others. Have the vehicle serviced at specified intervals or whenever a power steering problem is noticed.

WARNING

Do not grip the steering wheel spokes when driving off road. A bad bump could jerk the wheel and injure your hands. Keep both hands especially your thumbs on the outside of the steering wheel rim.

To help prevent damage to the power steering pump:

• Never hold the steering wheel to the extreme right or the extreme left for more than a few seconds when the engine is running
• Heavy or uneven steering efforts may be caused by low power steering pump fluid level. Check for low power steering pump fluid level before seeking service by an Authorized Mahindra Dealer
• Do not fill the power steering pump reservoir above the MAX mark on the reservoir, this may result in leaks from the reservoir

NOTICE

If the power steering system breaks down (or if the engine is turned OFF), you can still steer the vehicle manually, but it takes more effort.

If the steering wanders or pulls, check for:

• Under inflated tire(s) on any wheel(s)
• Uneven vehicle loading
• High crown in the centre of the road
• High crosswinds
• Wheels out of alignment
• Wheels out of balance
• Loose or worn suspension components

9.1.1 Tilt Steering

The steering wheel can be adjusted for both rake and reach as required using the lever in the steering shroud under the steering wheel.

To tilt/adjust the steering wheel;

1. Pull the tilt lever down to unlock.

2. Raise or lower the steering wheel to the desired position.
3. Pull or push the steering wheel to the desired position.
4. Push the tilt lever back up to its original position to lock the steering.

WARNING

improperly locked steering wheel could cause loss of control and lead to accidents. Never adjust the steering wheel while driving.

9.2 teering Controls - Audio (if equipped)

The steering wheel also houses switches to control the main audio functions.

NOTICE

Refer to the Audio/Infotainment Manual for complete information on audio system features and controls.

9.2.1 Steering Audio Operations

A	Mute	C	Source Selection
B	Volume + / -	D	Up / Down or Call Selection

• SOURCE - Press SOURCE button to toggle between AUX, BLUETOOTH, TUNER & USB mode
• Leaving unattended children in a vehicle is dangerous for a number of reasons. Children should be warned not to touch the parking brake or the gear shift lever. Do not leave the key in the ignition. A child could move the vehicle leading to accidents
• VOLUME CONTROL - Press ‘+’ and ‘-’ button to increase or decrease the volume
• MUTE - Press MUTE button to mute audio while in TUNER and AUX mode and pause the song while in BLUETOOTH, USB mode
• BLUETOOTH USB MODE - Press ‘UP’ /‘DOWN’ button to go to next/previous track

TUNER MODE - Press ‘UP’ /‘DOWN’ button to go to next/ previous frequency. Press ‘UP’ /‘DOWN’ button for 2 seconds to AUTO TUNE

9.3 Brakes

Your vehicle is equipped with disc brakes in the front and drum brakes in the rear.

Disc brakes offer good braking capability and reduced stopping distance. Wet brake discs result in reduced braking efficiency. After a car wash or driving the vehicle through water, dab the brake pedal while driving to remove the film of water from the brake pads. Brake pads feature wear indicator. When the brake pad is worn, metallic squeal noise is heard indicating the pad wear. Have them replaced immediately.

WARNING

Driving with wet brakes is dangerous. Stopping distance increases considerably when braking.

Dry the brakes by driving at very slow speed and applying the brakes lightly until the brake performance becomes normal.

CAUTION

Even if the power assist (vacuum assistance) is completely lost, the brakes will still work. The brake pedal would be much harder than normal and the vehicle stopping / braking distance will be longer than usual.

9.3.1 Parking on a Hill/Incline

If you have to park facing uphill, select first gear and turn the front wheels away from the kerb. If you have to park facing downhill, select reverse gear and turn the front wheels towards the kerb. Always ensure the vehicle is in gear and parking brakes is engaged before leaving the vehicle.

9.3.2 Parking Brake

To apply the parking brake, pull the park brake lever up as firmly as possible. When the parking brake is applied with the ignition ON, the brake warning lamp in the instrument cluster illuminates. To release the parking brake, pull the parking brake lever up slightly, press the release button on the lever tip and lower the parking brake lever completely.

NOTICE

The brake warning lamp indicates only the parking brake status. It does not indicate the degree of brake application. Be sure the parking brake is firmly set when parked and the gear shift lever is in gear. When parking on a hill you should apply the parking brake before placing the shift lever gear, since the load on the transmission locking mechanism may make it difficult to move the shift lever out of gear.

CAUTION

Be sure the parking brake is fully disengaged before driving off. Failure to do so can lead to brake problems due to excessive heating of the rear brakes.

• The parking brake should be adjusted as per recommended maintenance schedule
• Always apply the parking brake when leaving the vehicle, and be certain to leave the transmission in gear. Failure to do so may allow the vehicle to roll and cause damage, hit a bystander resulting in personal injury.
• Leaving unattended children in a vehicle is dangerous for a number of reasons. Children should be warned not to touch the parking brake or the gear shift lever. Do not leave the key in the ignition. A child could move the vehicle leading to accidents
• The parking brake should always be applied when the driver is not in the vehicle.

Engaging the parking brake while the vehicle is in motion can cause the rear wheels to lock up. You could lose control of the vehicle and cause an accident.

9.5 Anti-Lock Brake System (ABS) (if equipped)

The Anti-lock Brake System (also called as ABS) is designed to help prevent lock-up of the wheels and stable stopping of vehicle during a sudden, panic emergency braking or braking on slippery road surfaces. The ABS system takes input from wheel speed sensors and brake pedal switch to control the brake fluid pressures at the wheels to avoid wheel lock-up. It allows vehicle to be steered during braking.

The minimum speed for ABS to function is 12 kmph. ABS is activated only during wheel lock conditions where ABS takes over and prevents wheel lock.

During the ABS operation, a slight pulsation may be felt in the brake pedal to indicate ABS is active. You may also hear motor noise from the engine compartment. It is recommended to hold the brake pedal firmly while the ABS is active rather than pumping the brake pedal.

Depressing the brake pedal on slippery road surfaces as on a manhole cover, a steel plate at a construction site, a joint in a bridge, etc. on a rainy day, tends to activate the anti-lock brake system.

The ABS warning lamp lights up when you switch ON the ignition and should go out after a few seconds. If the ABS warning lamp does not go out or if it comes ON while driving, it means there is a fault in the ABS system. In both cases, the normal braking system remains efficient, exactly as on a vehicle without ABS. The vehicle should be examined as soon as possible by an authorized Mahindra dealer.

The Anti-lock brake system is not designed to shorten the stopping distance: Always drive at a moderate speed and maintain a safe distance from the vehicle in front of you. The stopping distance may be longer in the following cases:

• Driving on rough, gravel or snow covered roads.
• Driving with tyre chains installed.
• Driving over the steps such as the joints on the road.
• Driving on roads where the road surface is pitted or differences in surface height.

WARNING

Do not overestimate the Anti-lock Brake System: Although the Anti-lock Brake System assists in providing vehicle control, it is still important to drive with all due care and maintain a moderate speed and safe distance from the vehicle in front of you. There are limits to the vehicle stability and effectiveness of steering wheel operation even with ABS active.
If tyre grip performance exceeds its capability, or if hydroplaning occurs during high speed driving in the rain, the Anti-lock Brake System will not assist with vehicle control.

10.1 HVAC Overview

A	Side Vents	D	Side Defrost Vents
B	Centre Vents	E	Foot Vents
C	Windshield Defrost Vents	F	HVAC Controls

10.1.1 Centre/Side Vents

A

Adjustable Louvers

B

Thumb Wheel

Two centre vents are located on either side of the infotainment screen in the centre console. The two side vents are located one each at the left and right extreme ends of the instrument panel. Both the centre and side vents provide air flow to the front seat passengers.

Rotate the thumb wheel (B) left to close or right to open the air vent. Direct air to the desired direction by the adjusting louvers (A) up/down or left/right.

10.1.2 Defrost Vents - Side/Windshield

There are four defrost vents in your vehicle; two side defrost and two windshield defrost vents. They are located just below the windshield. The side defrost vents prevent the front windows from de-misting, whereas the windshield A Adjustable Louvers B Thumb Wheel defrost vents help in clearing the mist from windshield.

10.1.3 Second/Third Row Roof Vents

Two (LH & RH) vents for the second row are provided on the B-Pillars. The vents have adjustable louvers to direct the air flow and thumb wheels for vents open/close operations.

The third row vents (LH & RH) are located on side trims on either side of the third row seats.

10.2 Climate Control

There are two types of climate control depending on the variant ;

A	Temperature Control Dial	G	Front Windshield Defrost
B	Economy Button (ECon)	H	Floor Defrost Mode
C	AC ON	I	Floor Mode
D	Re-circulation Mode	J	Face Floor Mode
E	Rear AC (Third Row)	K	Face Mode
F	Blower Fan Speed Control Dial	L	Rear Windshield Defrost

10.3 Temperature Control

A	Cool Air
B	Hot Air

By operating the temperature control knob, temperature of air being discharged from various vents can be adjusted to the desired level. Engine coolant is utilized to heat whereas the air conditioner is used to cool the air inside the AC unit. Based upon selected position of the temperature control dial, the desired discharged air temperature can be obtained.

By rotating the dial counter-clockwise and setting it to the extreme left position, cool air is discharged.

When the dial is rotated clockwise, the discharge air progressively starts getting warmer.

By rotating the dial further in the clockwise direction and setting it to the extreme right position, hot air is discharged.

10.4 Blower Speed Control

Blower force-circulates air through the HVAC unit and distributes it throughout the passenger compartment.

To increase the blower speed, rotate the control dial clockwise (B) and to reduce the blower speed, rotate the dial counter clockwise (A).

To switch OFF the blower, rotate the dial to “0”.

Third Row Blower Speed Control

A blower control is provided below the third row (RH) vent to control the air flow to the third row vents.

NOTICE

The third row AC is switched ON by the Rear AC button on the central switch bank. The airflow is controlled by the blower control on the third row RH side trim.

10.5 Economy Button (ECon)

ECON switch turns ON economy mode. During ECON AC operation the system automatically cuts OFF at a higher temperature than normal AC. The operation can be used during mild weather conditions for better fuel efficiency. Comfort level may be compromised during this operation.

LED on the button indicates the status of the button. Press the ECON switch again to turn OFF economy mode.

10.6 Air-conditioner ON (AC ON)

This button turns the air-conditioner ON or OFF. Adjust the temperature control dial as per the temperature requirement. LED on the button indicates the status. Push the button to turn ON/OFF the AC.

When the air conditioner is functioning, air gets cooled and de-humidified before being circulated inside the cabin. In hot weather conditions, it will take a slightly longer time to cool the interior as compared to cooler weather. Fuel consumption will be relatively higher if the vehicle is being driven with the air conditioner ON.

NOTICE

AC will function only when both engine and blower are switched ON.

NOTICE

• In certain operating conditions when the engine gets overheated, the engine management system may switch off the air conditioner intermittently.
• The air conditioner should be operated at least for ten minutes once every fortnight, even during winter months. This allows AC system components to get lubricated periodically and ensures optimum system
• During extreme cold weather conditions, the air conditioner may not function until temperature of the air near the evaporator rises above a predefined threshold.
• When air conditioner is ON, moisture is extracted from the air. The resulting condensate is drained off from the vehicle. It is therefore normal, if you see a small pool of water under your vehicle.

10.7 Re-circulation Mode

To set the HVAC system to recirculation mode, press the recirculation mode button. The LED on the button illuminates, indicating the recirculation mode is active.

In this intake mode, the air from inside the passenger compartment will be sucked by the blower and utilized further to ventilate/cool/heat the cabin.

For quick cabin cooling/heating or while driving through dusty/polluted region, re-circulation mode can be selected for short periods. Driving with this mode active may lead to better fuel economy and longer HVAC filter life.

However, running the air conditioner in re-circulation mode for long will make cabin air too dry and oxygen level drops inside cabin turning the air stale. On the contrary, keeping air intake control in recirculation mode for long, with air conditioner switched OFF, will make cabin air too humid and are more likely to become foggy. Hence never drive in recirculation mode for long, shift back to fresh air mode as soon as possible.

WARNING

Never keep recirculation mode selected continuously for long. Prolonged use of the HVAC system in recirculation mode may cause windshield/windows to mist/fog-up, impairing visibility which can lead to an accident, endangering you and others.

10.8 Fresh Air Mode

To set the HVAC system to fresh air mode, press the re-circulation mode button again. The LED on this button switches OFF, indicating that re-circulation mode is active.

10.9 Rear AC

The rear AC provides cooling for the third row AC vents. Adjust the temperature control dial as per the temperature requirement. LED on the button indicates the status.

NOTICE

The rear AC can be switched ON only when the AC button (front/second row AC) is ON.

10.12 Air Distribution Mode

Air distribution mode allows you to select the below air flow patterns;

• Face Mode — Air is discharged through the centre and side vents on the instrument panel, and through the second row B-pillar vents
• Face and Floor Mode — Air is discharged through the centre, side and foot vents on the instrument panel, and through the second row B-pillar vents
• Floor Mode — Air is discharged through the foot/floor vents on the instrument panel
• Floor Defrost Mode — Air is discharged through the foot/floor vents, windshield vents and side defrost vents on the instrument panel.

Press the required mode button on the switch bank.

10.14 Front Windshield Defogging/De-misting

Front windshield glass defogger switch is located on the blower speed control dial in the central switch bank. Press the switch once to activate the defogger. The lamp on the switch illuminates upon activation. AC is turned ON, air is discharged through the windshield defroster vents, side defroster vents and side vents. Air intake mode is switched to fresh air mode automatically. The defogger heats the front windshield clearing the fog/ frost.

Switch OFF the defogger by pressing the switch again as soon as the fog/frost is cleared.

If the windshield defogger switch is not switched OFF manually, it will turn OFF automatically after a pre-defined time, based on ambient temperature.

If you want to switch the defogger ON again, press the defogger switch again.

On second and subsequent activations of the rear windshield defogger in the same ignition cycle, the defogger ON time will be half the duration of the first activation.

10.15 Rear Windshield Defogging/De-misting

Rear windshield glass defogger switch is located on the temperature control dial in the central switch bank. Press the switch once to activate the defogger. The lamp on the switch illuminates upon activation and the defogger heats the rear windshield clearing the fog/ frost.

Switch OFF the defogger by pressing the switch once as soon as the fog/frost is cleared.

If the windshield defogger switch is not switched OFF manually, it will turn OFF automatically after a pre-defined time, based on ambient temperature.

If you want to switch the defogger ON again, press the defogger switch again.

On second and subsequent activations of the rear windshield defogger in the same ignition cycle, the defogger ON time will be half the duration of the first activation.

11.2 Starting the Engine

A	Accelerator Pedal	B	Clutch Pedal
C	Brake Pedal	D	Dead Pedal

Make sure all vehicle occupants are properly seated in their seats and have buckled their safety belts. For more information on seat, headrest positioning, safety belts and their proper usage, refer to the “Seat Belts” section in this manual.

NOTICE

Before cranking the engine

• Make sure the gear shift lever is in neutral
• Make sure the parking brake is engaged. Turn the key to IGN position but do not turn the key to start
• Few warning lamps briefly illuminate. See “Warning Lamps in the Instrument Cluster” section for more information

1. Shift the gear shift lever to neutral position.
2. Apply parking brake.
3. Turn the ignition ON.
4. Do not press the accelerator.
5. Turn the key momentarily to the START position to crank the
6. Once the engine starts, release the key; it will return to the IGN position
CAUTION

Do not continue cranking after the engine has started. This will lead to damage of the starter and other engine components.

7. If the engine fails to start, attempt to restart after about 10
8. If the engine fails to start even after repeated attempts as per the procedure given above, contact the nearest Authorized Mahindra Dealer
CAUTION
9. To prevent damage to the starter, wait 10 seconds before attempting to restart the engine.
WARNING
10. If the vehicle battery has discharged, use booster cables, a booster battery or a battery from another vehicle to start. Jump-starting a vehicle can be dangerous if done improperly. Refer to the “Jump-starting procedure” section in this manual.
11. If the engine still fails to start, contact an Authorized Mahindra Dealer for assistance.
12. The idle speed is controlled automatically and it will decrease as the engine warms up.
Observe the following when the engine is running;
• All warning lamps are OFF
• Low oil pressure lamp is OFF

After idling for a few seconds, release the parking brake, depress the clutch, shift the gear shift lever to 1st gear, release the service brake pedal, drive by releasing the clutch and depressing the accelerator pedal simultaneously.

11.2.1 Engine Idling - In Cold Weather

Avoid full throttle operation when the engine is cold and prolonged idling at low ambient temperatures. Long periods of idling may be harmful to your engine. Combustion chamber temperatures can drop so low that the fuel may not burn completely. Incomplete combustion allows carbon and varnish to form on piston rings and injector nozzles. Also, the unburned fuel can enter the crankcase, diluting the oil and causing rapid wear to the engine.

11.8 Ignition Switch

An illuminator ring is provided on the face of the ignition switch to help in locating the ignition switch at night. The ring will illuminate the moment the driver door is opened and will remain glowing till the driver door is closed.

The different positions of the ignition switch are;

LOCK - This is the ignition and steering lock position. The vehicle circuits and engine is completely switched OFF. The steering wheel is also locked and the key can be removed from the ignition only in this position.

ACC - The steering is unlocked and can be rotated. In this position all electrical circuits are enabled. Use this mode when you want to listen to music, etc., with the engine temporarily switched OFF.

ON - All electrical circuits are enabled. Some of the warning or information lamps illuminate in this position. While some of the lamps will go out after a few seconds, some will continue to remain ON till the engine is started. When the vehicle is being driven, ignition switch remains in the ON position.

NOTICE

Do not leave the ignition in ON when the engine is OFF. This could lead to battery drain and ignition switch damage.

START - This position is to start the engine by cranking the starter motor. This is a momentary position. When the key is turned to start position, the starter cranks the engine. Once the engine is running, release the key, and the key reverts back to ON position and the starter motor disengages from the engine.

CAUTION

Do not continue cranking after the engine has started. This will lead to damage of the starter and other engine components.

NOTICE

If turning the key is difficult, jiggle the steering wheel from side to side and try again.

The key can be removed only in the LOCK position. When the key is removed, the steering column lock is activated and the steering wheel cannot be turned.

WARNING

Never return the key to the LOCK position or try to remove the key, when the vehicle is in motion. Removing the key allows the steering wheel to lock. You will loose the control of the vehicle and may cause serious accident. Remove the key only when the vehicle is parked.

11.9 Transmission

The first few shifts on a new vehicle may be somewhat rough. This is a normal phenomenon, and precision shifts will develop within the initial few hundred kilometers of running.

11.9.1 Gear Lever

Your vehicle is fitted with manual transmission having six forward and one reverse gear. This shift pattern is imprinted on the gear lever knob. The transmission is fully synchronised in all forward gears so shifting to either a higher or a lower gear is easily accomplished. The clutch pedal should be depressed fully while shifting, and then released slowly.

11.9.2 Gear Indicator

The current gear lever position is indicated in the centre of the speedometer dial.

11.9.3 Neutral Position

This position stops the transmission of power from the engine to drive axle. With the gear lever in neutral and brakes released, the vehicle can move freely by pushing or towing. The engine can be started in this mode. It is always recommended to keep the brake pedal depressed in this position. It is advisable to shift into neutral when the vehicle is standstill for longer durations with the engine idling.

WARNING

Coasting the vehicle with the gear lever in neutral and engine ON/OFF is not recommended. In an event of panic braking, you will not have the power of engine braking to slow down the vehicle. This may lead to personal injury or accident.

CAUTION

Do not leave the vehicle with the gear lever in neutral position. Always engage manual parking brake before leaving the vehicle, to prevent any vehicle movement leading to possible injury to a by-stander or damage to vehicle.

11.9.4 Gears 1-6

Use the gears 1 to 6 as per vehicle load, road/traffic conditions or as per requirement. The current gear selection is indicated in the cluster.

CAUTION

Always depress the clutch fully before moving the gear lever from the current position to any desired position. Perform up-shifts or down-shifts one gear at a time, do not jump gears.

11.12 All Wheel Drive (AWD) Operation (if equipped)

In an AWD vehicle, power is transmitted to all the wheels. This is managed by the AWD System which intelligently transfers torque to all four wheels. AWD system includes electromagnetically operated clutch which is controlled by an ECU. According to the driving conditions this system automatically delivers torque to the rear wheels.

11.12.1 AWD System

AWD system is available in two operating positions viz., AUTO mode and AWD LOCK mode. Once the ignition key is turned ON, AWD system by default turns into AUTO mode. In AUTO mode, whenever a slippage is detected in the FRONT wheels (slippery surfaces like icy roads, wet surfaces, etc.) the torque is transferred to the REAR wheels by the AWD system.

11.12.2 AWD Lock

AWD LOCK button is located on the central bezel switch bank. The LED on the switch turns ON when the AWD Lock is activated. In this mode fixed amount of torque is transferred to the rear wheels irrespective of the driving condition.

The AWD warning lamp in the cluster illuminates when there is a malfunction in the AWD system.

CAUTION

AWD vehicles have to be towed only with the rear wheels lifted off the ground or on all four wheels. If vehicle needs to be towed by lifting the front wheels, then the propeller shaft needs to be disconnected in order to protect the coupling.

11.13 Electronic Stability Program (ESP) (if equipped)

This system enhances directional control and stability of the vehicle under various driving conditions. The ESP corrects for over-steering and under steering behavior of the vehicle by applying the brake of the appropriate wheel automatically. Engine power may also be reduced to assist in counteracting the condition of over-steer or under-steer and help the vehicle maintain the desired path.

ESP uses steering angle sensors and YAW rate sensor to determine the path that the driver intends to steer the vehicle and compares it to the actual path of the vehicle. When the actual path does not match the intended path, the ESP applies the brake of the appropriate wheel to assist in counteracting the condition of over-steer or under-steer.

Over-steer - when the vehicle is turning more than appropriate for the steering wheel position.

Under-steer - when the vehicle is turning less than appropriate for the steering wheel position.

WARNING

The ESP cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. The ESP cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents. The capabilities of an ESP equipped vehicle must never be exploited in a reckless or dangerous manner that could jeopardize the user’s safety or the safety of others.

11.13.1 ESP ON

Whenever the vehicle is started, the ESP system will be in active mode. This mode should be used for most driving conditions.

When the ESP is in operation, ESP indicator lamp blinks in the instrument cluster.

NOTICE

When the ESP is operating, you can feel a slight pulsation in the vehicle. This is only the effect of brake control and indicates nothing unusual.

When moving out of the mud or slippery road, accelerator response may be different because ESP system controls the engine rpm to come out this slippery road condition. This is normal.

11.13.2 ESP OFF

In some driving conditions, to maximise traction, it may be beneficial to de-activate ESP.

Such conditions are;

• To start in deep snow or on a loose surface
• Driving in deep sand
• Driving through deep mud etc.

To de-activate ESP, press ESP OFF button on the central bezel switch bank. Once ESP OFF mode is selected, a warning indicator illuminates in the instrument cluster.

Press ESP OFF button again to activate ESP function.

NOTICE

Mahindra recommends that ESP be operational in all normal driving conditions.

When ESP is in OFF mode, other functions like HHC (Hill Hold Control) HBA (Hydraulic Brake Assist), HDC (Hill Descent Control), DTC (Drag Torque Control), ROM (Roll Over Mitigation) will be in working mode.

However for safety reasons, if the ESP system detects that the vehicle is going into a unstable condition, ESP will be automatically activated on depressing the brake pedal

ESP, by default, will be in ON condition for every ignition cycle.

If the ESP indicator blinks while driving, it indicates that ESP is working. If this indicator illuminates continuously, it indicates a malfunction in the ESP system. Drive carefully to the nearest Authorized Mahindra Dealer and get the ESP system checked.

11.14 Hill Descent Control (HDC) (if equipped)

Assists the driver to descend a steep hill (max 50% inclination) by means of brake intervention limiting the vehicle speed without driver's input.

During HDC if the wheel slip becomes excessive, ABS will be activated automatically.

HDC is a user intended function. To activate press HDC button on the central bezel switch bank. The LED on the button illuminates indicating the status. Press the button again to de-activate HDC.

During a descent, if the vehicle speed is more than the rated speeds (refer recommended shift speeds), HDC (if selected) automatically operates the brakes to slow the vehicle and maintain a speed relative to the selected gear and the accelerator pedal position.

HDC will also work in neutral gear, and maintains the vehicle rolling speed by operating brakes automatically. HDC will deactivate automatically, if the vehicle speed is more than 45 kmph.

While HDC is controlling the vehicle speed, descent speeds can be varied using cruise control switches mounted on the steering wheel.

To decrease speed, press and hold “SET -” button. The vehicle speed at the point of switch release will become the new descent speed.

To increase, press and hold “SET +” button. The vehicle speed at the point of switch release will become the new descent speed. Alternatively, descent speeds can be adjusted by tapping the “SET _” or “SET +” buttons. Each press of the button will adjust the speed by approximately 0.5 kmph.

NOTICE

The descent speed increases only if the gradient is sufficiently steep to cause the vehicle to accelerate as the braking effect is reduced. On a shallow slope, pressing the “SET +” button may result in no speed increase.

If the brake pedal is depressed when HDC is active, HDC is overridden and the brakes will perform as normal (a pulsation might be felt through the brake pedal). If the brake pedal is then released, HDC will recommence operating if necessary.

HDC system monitors the brake temperature continuously. If brake application is continuous and brake temperatures are too high, HDC de-activates automatically. This is to ensure that the brake pads are not worn due to continuous brake application.

11.15 Hill Hold Control (HHC) (if equipped)

HHC will prevent the vehicle from rolling to the opposite direction of the driver intended direction.

Hill Hold Control with acceleration sensor identifies gradients and holds the vehicle for about a second after the brakes have been released in order to prevent the vehicle from accidentally rolling backwards during a hill start.

Imagine a situation where your vehicle is stopped on an uphill incline. If you release the brake while moving off, there are chances that your vehicle may roll back. HHC helps in such situations by holding the vehicle from rolling back.

NOTICE

HHC will be active only when the TGS in “D”, “R” or “M” mode.

11.16 Cruise Control (if equipped)

Cruise control allows you to maintain a set speed without the need to keep your foot on the accelerator pedal. It should be used for cruising on straight, open highways. Never use it for city driving, inclines, winding roads, slippery roads, heavy rain or in bad weather conditions.

It works on the closed loop system principle to maintain the set speed of the vehicle; the system controls the fuel injection of the engine in order to maintain the set speed.

A	Resume	C	SET +
B	Cruise Off	D	SET-

Cruise control enhances your comfort while driving and allows you to effortlessly maintain the desired lane speed limit. Improper use of the cruise control can lead to an accident.

NOTICE

Cruise control is designed to operate above a vehicle speed of 20 kmph for all gears except 1st and reverse gears. The cruise lamp in the instrument cluster functions only if the cruise control is active.

Cruise control will function only under the following conditions;

• The vehicle is cruising above 20 kmph.
• Engine RPM above 1200 RPM.
• Vehicle is in any gear except reverse.
• Brake pedal released.
• Cruise is activated first time in an ignition cycle by SET+ /SET- button.
• Subsequent cruise engagements can be done by RESUME SET+ /SET- buttons in the same ignition cycle.
Cruise control is deactivated under the following conditions;
• CRUISE OFF button is pressed.
• Brake pedal depressed.
• If the vehicle speed exceeds the cruise set speed by 30 kmph by accelerator pedal intervention.
• If vehicle speed is increased by 10 kmph for more than 30 sec. by pressing the accelerator pedal.
• When Set+/Set- switch is pressed for more than 12 sec. (In this case vehicle will not go into cruise mode in that ignition cycle. In order to restore the cruise function switch OFF the ignition, wait for 30 sec. and switch ON the ignition)
• Cruise influencing error indicated by Check Engine Lamp, OBD lamp, etc.,

11.16.1 Cruise Control Activation

Drive the vehicle to the desired cruising speed (any value greater than 20 kmph), press and hold the SET+ button until the cruise lamp in the instrument cluster illuminates.

If cruise is deactivated (eg. by depressing brake to handle an intervention in the road etc.,) in current driving cycle, reactivate the Cruise to the last active Cruise Speed by pressing the RESUME button.

Cruise control may not hold the set speed when you are going up or down hills, and the vehicle may come out of cruise control. This is indicated by the cruise lamp going OFF in the instrument cluster.

11.16.2 Cruise Control De-activation

You can cancel cruise control in any of the following ways;

• Press the CRUISE OFF button in the steering wheel.
• Press the brake pedal.
• Gear selector moved into neutral.
• HDC or ESP becomes active.

11.16.3 SET+ Button

SET+ button is used to activate cruise control and also to increase the cruise set speed.

To increase the speed in very small amounts, press the SET+ button. Each time you press, the cruise set speed increases by about 2 kmph. When you wish to continuously increase the cruising speed, press and hold the SET+ button and release when the desired speed is reached.

11.16.4 SET- Button

To decrease the speed in small amounts, press the SET - button. Each time you press, the cruise set speed decreases by about 2 kmph.

When you wish to continuously decrease the cruising speed, press and hold the SET- button. When the desired speed is reached, release the button.

CAUTION

If switch is pressed for more than 12 secs, the switch is assumed to be malfunctioning and the cruise functionality ceases to function in that ignition cycle. To resume functionality, ignition has to toggled.

WARNING

The cruise control is a convenience system designed to assist the driver during vehicle operation. The driver must at all times remain alert of road/traffic conditions and responsible for the vehicle brake operation / steering control.

WARNING

Never activate cruise control in traffic or when driven in adverse road conditions (heavy rains, windy, slippery etc.)

11.16.5 RESUME Button

With the help of RESUME, you can opt for the previous set cruising speed of the vehicle in the same ignition cycle. This is best explained with the following example:

1. Assume, you have activated cruise mode and set the vehicle speed at 50 kmph.
2. Due to an obstacle or a sharp turn, you have deactivated the cruise mode either by pressing the brake pedal or by switching OFF the CRUISE control.
3. Vehicle comes out of the cruise mode.
4. When the road condition is suitable to switch over back to cruise control mode, press RESUME button once. The system activates the cruise control mode to the previous cruising speed of 50 kmph.
5. To resume the previous cruise set speed, the vehicle speed should be above 20 kmph.

11.16.6 Override Function

This function enables user to ramp up the cruising speed to overtake front vehicle.

The cruising speed can be increased by using accelerator pedal. User has to complete this action within 30 seconds, to maintain the cruise mode. If user exceed the 30 seconds limit, cruise mode will be deactivated.

11.17 Fuel

Use only commercially available vehicular Ultra-low Sulfur Highway Diesel that meets the BIS standard (Conforming to IS 1460;2010 BSIV/BSIII specification or equivalent). Information on diesel quality can normally be found in the fuel pump. Please contact filling station personnel in case labels in the pump cannot be found.

CAUTION

Do not fill the fuel tank or mix the fuel with gasoline, alcohol based fuels, kerosene, etc. This will damage the engine, fuel and exhaust system components.

If you have accidentally filled the fuel tank with incorrect or non-approved fuel, do not start the vehicle. Contact an Authorized Mahindra Dealer to have the fuel system drained completely.

11.17.1 Fueling during Winter

During freezing weather if fuel is not winterized or is insufficiently winterized, waxing/gelling may start in fuel, leading to interruption in fuel supply to engine. For smooth functioning and reliable operation of the engine during cold weather conditions, use winterized ULSD which are available at the filling stations during winter months. Check with your fuel retailer for further details.

CAUTION

Avoid inhaling fuel vapors and any skin or clothing contact. Direct skin contact with diesel or the inhalation of fuel vapor may affect your health

WARNING

Diesel is highly flammable and poisonous. It burns violently and can cause serious injury. Never allow sparks, flames or smoking materials near diesel. Turn OFF the engine before refueling. Whenever you are around diesel, extinguish all smoking materials.

11.17.2 Minimum Fuel Requirement

It is recommended maintaining a minimum of 10 liters of fuel in the fuel tank. Driving the vehicle till the fuel tank is empty is not recommended. Always have sufficient fuel in the tank. Check the fuel level prior to starting your journey.

CAUTION

Never carry fuel in separate containers in the vehicle, it is dangerous and may lead to inadvertent fuel leak or spillage.

11.17.3 Fuel-Lid Opening and Closing

The remote fuel-lid can be opened by gently pressing the fuel lid button (adjacent to the head lamp leveling switch) on the instrument panel driver side.

NOTICE

Fuel filler lid cannot be released when the vehicle speed is more than 20 kmph.

Fuel filler lid operation is limited to 8 times / minute. Avoid unnecessary usage of fuel filler lid button.

Turn the fuel cap counter-clockwise to open. Refuel and put the cap back in its place and tighten in the clockwise direction till three distinct clicks are heard. Close the fuel lid shut.

CAUTION

Ensure the fuel cap and lid are securely closed before starting the vehicle.

11.17.4 Mechanical Override for Fuel Lid Opening

In the unlikely event of remote switch not opening the fuel lid, a mechanical over ride release is provided. It is located in the luggage compartment LH trim area behind the third row seats. Turn the knob anti-clockwise to open the fuel lid.

12.1 Tire Information

A	RADIAL TYRES OR BIAS-PLY TYRE.
B	“TUBELESS” OR “TUBE TYPE”
C	TYRE SIZE
D	MAX LOAD LIMIT
E	TREAD WEAR

12.2 Tyre Rating

Your vehicle is originally equipped with tyres supplied by a reputable manufacturer. If you ever have any questions regarding your tyres, please refer to literature supplied by the tyre manufacturer, or to the separate tyre warranty provided by the tyre manufacturer. You may also contact Mahindra directly, or the tyre manufacturer.

The tyre rating of XUV500 is;

• 235/65 R17 104H

Tyre rating is explained as below;

Tyre size (example: 235/65 R17 104H)

Callout (A): 235 (Three-digit number): This number gives the width in millimeters of the tyre from sidewall edge to sidewall edge. This is called as “Section Width”.

Callout (B): 65 (Two-digit number): This number, known as the aspect ratio, gives the tyres ratio of height to section width.

Callout (C): R: This is the Tyre Construction Code. The “R” stands for Radial.

Callout (D):17 (Two-digit number): This number is the wheel or rim diameter in inches.

Callout (E):104 (Two or three digit number): This number is the tyres load index. It is a measurement of how much weight each tyre can support.

Callout (F): H: Tyre speed rating or speed symbol. Never drive the vehicle faster than the tyre speed rating. The speed rating denotes the speed at which a tyre is designed to be driven for extended periods of time under a standard condition of load and inflation pressure.

12.2.1 Speed Rating

SPEED SYMBOL	MAX SPEED CAPABILITY	SPEED SYMBOL	MAX SPEED CAPABILITY
	KM/HR		KM/HR
L	120	T	190
M	130	U	200
N	140	H	210
P	150	V	240
Q	160	W	270
R	170	Y	300
S	180	Z	240+

12.3 Tyre Label (Vehicle Placard)

Tyre Label (Vehicle Placard) is located on the driver side inner B-pillar. This placard tells you important information about tyre size designed for your vehicle, and the tyre inflation pressures for the front & rear tyres.

XUV500 COLD TYRE INFLATION PRESSURE bar/psi/kPa
TYRE	P 235/65 R17
FRONT	2.2 / 32 / 220
REAR	2.0 / 30 / 200

WARNING

Never overload your vehicle. Overloading can cause tyre failure, affect vehicle handling, and increase your stopping distance, resulting in an accident and/or serious personal injury.

Improper inflated tyres can adversely affect vehicle handling or can fail unexpectedly, resulting in an accident and/or serious personal injury.

12.5 Tire Rotation Recommendations

Type 1 - Applicable for all 5 Steel / 5 Alloy wheels

Tires on the front and rear axles of vehicles operate at different loads and perform different steering, handling, and braking functions. For these reasons, they wear at unequal rates and develop irregular wear patterns.

Rotation will increase tread life, help to maintain mud, snow, and wet traction levels, and contribute to a smooth, quiet ride. Follow the recommended tire rotation frequency for your type of driving.

Type 2 – Applicable for 4 Alloy wheels and Spare wheel with Steel rim

It is recommended rotating the tires as per the “Maintenance Schedule”.

The suggested rotation method is the “forward-cross” shown in the diagram. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on On/Off-road type tires.

Rotation will increase tread life, help to maintain mud, snow, and wet traction levels, and contribute to a smooth, quiet ride. Follow the recommended tire rotation frequency for your type of driving. More frequent rotation is permissible if desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being performed.

12.5.1 Changing a Flat Tire

Refer to “If you have a Flat Tire” section in the general chapter for details.

12.5.2 Wheel Tightness

When you change a wheel, remove all rust and dirt at all locations where the wheel contacts the wheel hub. Use a scraper or wire brush to be sure that you remove all rust and dirt. A loose wheel could have damaged or elongated the holes in the rim, or damaged the rim/hub assembly. If any of the wheel studs or nuts are damaged, contact the nearest Authorized Mahindra Dealer.

WARNING

Always tighten the nuts in a crisscross sequence. Never use oil or grease on your wheel studs or nuts.

Never over tighten the nuts on the wheel stud. You could damage the stud or the nut.

Torque tighten the wheel nuts to the specified value at the nearest Authorized Mahindra Workshop.

NOTICE

The tyres fitted in this vehicle meet the requirements of BIS and they comply with the requirements under the Central Motor Vehicles Rules (CMVR) 1989.

12.6 Tiretronics (if equipped)

Tiretronics is an electronic system designed to monitor the air pressure inside the pneumatic tyres. This system will alert the driver if the tyre pressure falls below the low pressure or raises above high pressure warning limit for any reason, including low temperature effects and natural pressure loss through the tyre. The Tiretronics will continue to alert the driver and will not turn off until the tyre pressure is inflated to the recommended pressure.

12.6.1 Operation of Tiretronics

Tiretronics uses wireless technology with wheel rim mounted electronic sensors to monitor tyre pressure levels. Sensors mounted to the valve stem of each wheel, transmit tyre pressure readings to the receiver module. Receiver module in turn will communicate this information to the instrument cluster and infotainment system. Tyre locations will display as OK, if all tyre pressure and temperature are in the recommended range. The Tiretronics has been customized only for the manufacturer’s genuine tyres and wheels. Tiretronics pressure limits and warning messages have been established for the tyre size equipped on your vehicle.

Replacement of manufacturer’s parts with a different size, type or style of components may damage the sensor and lead to incorrect readings.

Do not use aftermarket tyre sealants or balance beads if your vehicle is equipped with Tiretronics. Failure to comply may lead to sensor damage.

The Tiretronics is not intended to replace normal tyre care and maintenance or to provide warning of a tyre failure or condition.

The Tiretronics should not be used as a tyre pressure gauge while adjusting vehicle tyre pressure. Driving with under-inflated tyres cause the tyres to overheat and may lead to tyre failure. Under-inflated tyres reduce fuel efficiency, tyre tread life and may affect the vehicle's maneuverability & braking ability.

The Tiretronics is not a substitute for tyre maintenance, it is the driver's responsibility to maintain correct tyre pressure using an accurate pressure gauge, even if under-inflation has not reached the level to trigger illumination of the Tiretronics warning indicator.

12.6.2 Tiretronics Warning Lamp

Tiretronics warning lamp will blink for 75 seconds (approx) and remain ON in the instrument cluster, if any of the below mentioned condition occurs in the tyres;

• Sensor signal missing
• Sensor faulty

The error is also displayed on the infotainment screen as below. If above condition occurs, contact the nearest Authorized Mahindra Dealer for further assistance.

Examples of Tiretronics warning lamp illumination and corresponding infotainment screen display;

• Low pressure

• High pressure

• Air leakage

12.6.3 Tiretronics Learning

After a tyre rotation or Tiretronics sensor replacement, the receiver must be learnt, else the Tiretronics warning lamp indicates a malfunction.

Tiretronics learning button (A) is located to the left hand side of the instrument cluster.

12.6.4 Tiretronics Learning Procedure

1. Press the Tiretronics button in the cluster and turn ignition ON along with the button pressed. The infotainment screen displays as below and Tiretronics warning lamp in the cluster starts blinking.

2. Start removing air from front left tyre, once the tyre gets learnt, vehicle alarm and hazard lamps flash once. The infotainment screen display is as below.

3. Repeat the above step for front right tyre, rear right tyre and rear left tyre (in the same order). Corresponding infotainment screen displays are as below.

4. Start removing air from spare tyre. Once the tyre gets learnt, vehicle alarm and hazard lamps flashes to indicate all the tyres were learnt. The infotainment screen display is as below indicating all tyres were learnt successfully.

If there were any problem in learning, the alarm and hazard lamps flash 3 to 5 times to indicate the tyre learning was not complete.

12.6.5 Tyre Swap

If a tyre was swapped with the spare tyre, system alerts the user through infotainment as below;

Please note, if swapping is done for more than one tyre or with the other running tyres, system cannot identify the same and the system needs to be relearned.

NOTICE

If any one of the running tyres goes faulty, spare tyre is swapped with the running tyre and the vehicle is driven, then:

• the system automatically recognizes the swap
• interchanges the running tyre and spare tyre data

13.1 Hazard Warning Flashers

The hazard warning flasher button is located in the central bezel switch bank. Press the button to turn ON the hazard warning flashers, all directional turn signals will flash to warn oncoming traffic. This is an emergency warning system and should be used only when there is an emergency. Use it when your vehicle is disabled and is a safety hazard for other motorists. Hazard warning flasher will work in all positions of the ignition key and even when the vehicle is fully locked.

NOTICE

With extended use, the hazard warning flasher may drain your vehicle battery.

14.3 Engine Compartment

A	Degassing Tank	G	Dipstick
B	Power Steering Fluid Reservoir	H	Fuel Priming Pump
C	Front Windshield Washer Fluid Reservoir	I	Air Filter Assembly
D	Engine Oil Cap	J	Battery
E	Brake/Clutch Fluid Reservoir	K	Engine Compartment Fuse Box
F	Engine Cover

Maintenance is classified as below;

15.5 Maintenance Record

It's important to document the maintenance of your vehicle. For your convenience to maintain records of service, ecoupons are provided in the Warranty Information & Maintenance Guide. Every time you bring your vehicle in for scheduled maintenance, be sure to present this guide and certify the work. Also record the date of service, mileage at the time of service. This will make record keeping easy and, should your vehicle ever require warranty coverage, you will have all the documentation to show you've properly maintained it.

15.6 Maintenance Interval

Mahindra establishes recommended maintenance intervals based upon engineering testing to determine the most appropriate mileage to perform the various maintenance services. This protects your vehicle at the lowest overall cost to you. Mahindra recommends that you do not deviate from the maintenance schedules presented in this Maintenance Schedule.

15.7 Vehicle Self Maintenance - General Precautions

• Refer relevant sections of the manual before starting
• Set the parking brake
• Block the wheels to prevent the vehicle from moving unexpectedly
• Turn OFF the engine and remove the key
• Stay clear of hot vehicle parts
• Avoid repeated contact with fluids
• Do not let fuel, coolant and other fluids spill over electrical and hot vehicle parts
• Keep all open flames and other burning material like cigarettes away from the battery and all fuel related parts

WARNING

Do not start/run the engine when any engine/peripheral parts are removed.

14.2 Opening and Closing the Hood

The hood release lever is located in the driver side foot well area, below the instrument panel. To open the hood, follow the steps below;

1. Pull the lever below the driver side IP to release the hood

2. Lift the hood a little to access the safety latch holding the hood striker. This safety latch is located below the hood at the centre
3. Lift the safety latch and lift the hood
4. Release the unhinged end of the stay rod from its lock clip, swing the rod upwards and insert its unhinged end in the slot below the already lifted hood
5. Allow the hood to be supported by the stay rod

6. Do not apply any undue force on the bonnet when it is supported by the stay rod
WARNING

• Do not open the hood immediately after a drive; the engine compartment will be very hot.
• Always double check to be sure that the hood is firmly latched before driving away. If it is not latched properly, the hood could open while the vehicle is being driven, causing a total loss of visibility, resulting in an accident.
• Do not move the vehicle with the hood in the raised position, as vision is obstructed.

15.9 Closing the Hood

1. Remove the stay rod supporting the hood by slightly lifting the hood
2. Slowly lower the hood, while swinging down the stay rod and locking its unhinged end in the lock clip
3. Bring the hood just a few inches above its fully closed position
4. Now, release the hood and allow it to fall by its own weight. This ensures that safety latch firmly locks the hood in its fully closed position

15.10 Engine Compartment

A	Degassing Tank	G	Dipstick
B	Power Steering Fluid Reservoir	H	Fuel Priming Pump
C	Front Windshield Washer Fluid Reservoir	I	Air Filter Assembly
D	Engine Oil Cap	J	Battery
E	Brake/Clutch Fluid Reservoir	K	Engine Compartment Fuse Box
F	Engine Cover

Maintenance is classified as below;

• General Maintenance
• Scheduled Maintenance

In the Engine Compartment

• Front windshield washer fluid level
• Engine coolant level
• Battery condition
• Brake/Clutch fluid level
• Engine oil level
• Power steering fluid level
• Fluid leaks
• Hoses, joints and pipes for any abnormalities

Inside the Vehicle

• Lights
• Warning lamps
• Windshield wipe and wash
• Steering wheel
• Seats
• Seat belts
• Accelerator pedal
• Brake pedal
• Brakes
• Parking brake
• Gear lever shift mechanism

Outside the Vehicle

• Lamps
• Fluid leaks
• Doors and engine hood latches
• Tire inflation pressure
• Tire surface/thread and wheel nuts

14.5 In the Engine Compartment

14.5.1 Fluid Leaks

Check the engine compartment and the underbody of the vehicle for any leaks. If you smell fuel vapor or notice any leak, have the cause found and corrected immediately.

14.5.2 Engine Oil

Engine oil has the primary functions of lubricating and cooling the inside of the engine. It plays a major role in maintaining the engine in proper working order. Therefore, it is essential to check the engine oil regularly.

14.5.3 Engine Oil Consumption

It is normal for engines to consume some engine oil during operation.

Causes of consumption in a normal engine are as follows;

• Oil is used to lubricate pistons, piston rings and cylinders. Thin films of oil, left over when pistons move in cylinders, are sucked into the combustion chamber due to high negative pressure generated when the vehicle is decelerating. This oil gets burnt in the combustion chamber.
• Oil is also used to lubricate the stems of intake valves. Some of this oil is sucked into the combustion chamber together with the intake air and is burnt there.
• Engine oil consumption depends upon the viscosity and quality of the oil, and upon the conditions in which the vehicle is driven. Oil consumption will be more due to high speed driving and frequent acceleration and deceleration. A new engine may consume more oil since its pistons, piston rings and cylinder walls are not conditioned.

14.5.4 Checking/Topping the Engine Oil

• Make sure the vehicle is on level ground
• Turn the engine OFF and wait a few minutes for the oil to settle down into the oil sump
• Apply the parking brake
• Open the hood, use stay rod to support the hood. Protect yourself from engine heat
• Locate and carefully remove the engine oil level dipstick
• Wipe the dipstick with a clean cloth. Insert the dipstick fully, then remove it again
• If the oil level is between “Min” and “Max” marks, the oil level is acceptable. DO NOT ADD OIL
• If the oil level is below the Min mark, add enough oil through the oil filler cap to raise the level within the “Min” and “Max” marks. Wait for few minutes after every top up for the oil to settle down before checking the level.

• Oil levels above the “Max” mark may cause engine damage/poor performance.
• Put the dipstick and the oil filler cap back and ensure it is fully/properly seated.

CAUTION

To avoid possible oil loss and injury due to hot blow-by gas, DO NOT operate the vehicle with the engine oil level dipstick and/or the engine oil filler cap removed.

NOTICE

Draining/Changing of engine oil should always be done by an Authorized Mahindra Dealer.

14.5.5 Checking/Topping Engine Coolant Level

• Park the vehicle on flat-horizontal surface. Keep the parking brake fully engaged. Shut-off the engine

• Wait till the engine cools down and hence coolant temperature comes down to normal room temperature
• The coolant level should be between “MIN” and “MAX” marking provided on the degassing tank
• In case the coolant level is below the “MIN” marking, the coolant should be topped-up
• The coolant should be filled till the level rises above the 'MIN' but remain below the “MAX” marking on the degassing tank
• However if the degassing Tank is found to be near empty, it is recommended that the system be checked at an Authorized Mahindra Dealer

WARNING

Never open the pressure cap when the engine is hot. Hot coolant may splash resulting in serious personal injury or severe burns by the erupting liquid.

NOTICE

Top up only with recommended Ready To Use (RTU) coolants for ensuring performance, anti-freezing and corrosion protection. Do not add water directly. Mixing with other brand of coolants is not recommended and should be avoided.

NOTICE

Draining or changing of engine coolant should always be done by an Authorized Mahindra Dealer.

14.5.6 Checking/Topping Brake/Clutch Fluid

The brake and clutch systems are supplied fluid from the same reservoir.

The brake fluid level will drop slowly as the brakes wear, and will rise when the brake components are replaced. Fluid levels between the “MIN” and “MAX” lines are within the normal operating range; there is no need to add fluid. If the fluid levels are below the “MIN” mark, the performance of the systems could be compromised; the brake/clutch operation could be spongy and gear change harder. Top-up the recommended brake/clutch fluid till the “MAX” mark or contact an Authorized Mahindra Dealer immediately.

Carefully clean the cap on the reservoir before you remove it and be sure no debris fall in the reservoir. Do not keep the reservoir open for longer than necessary to add brake fluid.

Use only brake/clutch fluid that meets Mahindra specifications. Refer to ‘Lubricant and Capacities’ section.

NOTICE

Draining or changing of brake fluid should always be done by an Authorized Mahindra Dealer.

14.5.7 Checking/Topping Power Steering Fluid

Check the power steering fluid level at the defined service intervals. Refer to Maintenance Chart for details.

The fluid level should be checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as anticipated. Coordinate inspection efforts through an Authorized Mahindra Dealer.

CAUTION

Driving vehicle with power steering fluid below minimum mark will damage steering system.

CAUTION

Use only recommended power steering fluid. Do not use other types of power steering fluids which may damage the power steering system.

WARNING

Fluid level in the reservoir should be checked on a level surface with the engine OFF to prevent injury from moving parts and to ensure accurate fluid level reading.

Follow the below steps for checking and topping up the power steering fluid;

1. Start the engine and let it run until it reaches normal the operating temperature
2. While the engine idles, turn the steering wheel left and right a couple of times
3. Turn the engine OFF
4. Check the power steering fluid level in the reservoir
5. The fluid level should be maintained between the “MIN” and “MAX” marks
6. If the fluid is low, add fluid in small amounts, continuously checking the level until it reaches the correct operating range. Be sure to put the cap back on the reservoir
7. With a clean cloth, wipe any spilled fluid from all surfaces

NOTICE

Changing of power steering fluid should always be done by an Authorized Mahindra Dealer.

14.5.8 Windshield Washer Fluid Top-up

Top up both the front and rear (if equipped) windshield washer reservoirs as and when required.

The front windshield washer is located next to the power steering fluid reservoir in the engine bay. The rear windshield washer is located in rear luggage area LH trim behind the third row seats.

In very cold weather conditions, fill the reservoir with washer fluid premixed with anti-freeze.

CAUTION

If you operate your vehicle in temperatures below 4.5ºC, use washer fluid with anti-freeze protection. Failure to use washer fluid with anti-freeze protection in cold weather could result in impaired windshield vision and increase the risk of injury or accident.

14.5.9 Fuel Filter Bleeding/Priming

When the fuel level in the fuel tank falls very low, air may enter the fuel lines which leads to the engine not starting or abrupt switching OFF.

The air has to be removed from the fuel pump by priming the fuel pump. The fuel pump is located next to the air filter in the engine bay. Pump the fuel filter repeatedly using your palm and try starting the engine. If it fails, pump few more times and retry. If the engine still does not start, contact your nearest authorized Mahindra dealer for assistance.

14.8 Battery

Your vehicle is equipped with a Mahindra genuine battery. For longer, trouble-free operation, keep the top of the battery clean and dry. Also, make certain the battery cables are always tightly fastened to the battery terminals.

If you see any corrosion on the battery or terminals, remove the cables from the terminals and clean with a wire brush. To prevent corrosion, apply petroleum jelly to the battery terminals. Tighten loose terminals and hold down clamp nuts only enough to keep the battery firmly in place. Tightening excessively may damage the battery terminals.

14.8.1 For Best Battery Service

• Keep the battery securely mounted
• Keep the battery top clean and dry
• Keep the terminals and connections clean, tight and coated with petroleum jelly or terminal grease
• Rinse any spilled electrolyte from the battery immediately with a solution of water and baking soda

CAUTION

Do not disconnect battery terminals while the engine is running. This will adversely affect all electronic controllers.

WARNING

While removing the battery, always disconnect the negative terminal first. And while installing the battery, ensure the negative terminal is connected last.

It is recommended that the negative battery cable terminal be disconnected from the battery if you plan to store your vehicle for an extended period of time. This will minimize the discharge of your battery during storage.

WARNING

Battery fluid is a corrosive acid solution; do not allow battery acid to contact eyes, skin or clothing. Don't lean over battery when attaching clamps or allow the clamps to touch each other. If acid splashes in the eyes or on the skin, flush contaminated area immediately with large quantities of water.

A battery generates hydrogen gas which is flammable and explosive. Keep any flame or spark away from the vent holes.

Keep batteries out of reach of children. Battery posts, terminals and related accessories contain lead and lead components. Wash hands after handling batteries.

If the battery has been disconnected or a new battery has been installed, the clock (if equipped) and the preset radio (if equipped) stations must be reset once the battery is reconnected.

The replacement battery must meet the specification of the originally fitted battery.

14.8.2 Battery Charge Indicator - Amaron (if equipped)

A battery charge indicator is provided for Amaron batteries to view the charge status at a glance. Green indicates the battery is okay, and light blue indicates battery needs recharge or technical assistance from Amaron.

14.8.3 Battery Charge Indicator - Exide (if equipped)

14.8.3 Battery Charge Indicator - Exide (if equipped)

Three charge indicators are provided which give the following information;

• GREEN —OK (Battery condition good)
• WHITE — Needs charging
• RED —Add distilled water

14.8.4 Checking the Electrolyte Level

Check the electrolyte level and specific gravity at intervals of three months. Check all the six cells for proper electrolyte levels. If the level is below the lower marker, add distilled water until the level reaches the upper marker.

Adding distilled water;

• Remove the vent plugs
• Add distilled water to all the cells that require the fluid and secure the plugs properly

14.15 Projector Head lamp

A	Head lamp High Beam	D	Head lamp Low Beam
B	Parking Lamp	E	Turn Signal Lamp
C	Static Bending Lamp

NOTICE

Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol.

CAUTION

Using bulbs with units of higher output capacity/wattage is illegal and may damage your vehicle’s electrical system. Replacement bulbs must meet the specification of originally fitted bulbs.

CAUTION

14.16 Non Projector Head lamp

A	Head lamp High Beam	C	Head lamp Low Beam
B	Parking Lamp	D	Turn Signal Lamp