1.1 Introduction

Dear Customer,
Congratulations on purchasing Mahindra XUV500. Your vehicle has been designed to provide years of safe and dependable service, as long as it is used and maintained in accordance with the instructions provided in this manual.

All persons who will use and/or maintain this vehicle must read, understand and follow all warnings and instructions provided in this manual. This Owner's Manual should be considered an integral part of the vehicle and should remain with the vehicle. However, nothing in this manual, and none of the safety devices installed in the vehicle, are a substitute for careful operation and common sense. Always make sure that your vehicle is in optimum working order, and take note of the road and weather conditions under which you are using your vehicle.

If you have any questions concerning the proper use or maintenance of your vehicle, please call your Authorized Mahindra Dealer. A list of dealers can be found in the Dealer Directory Supplement.

Alternatively you can contact Mahindra at,

• 1800-209-6006 (Toll free)
• customercare@mahindra.com

We extend our best wishes for safe and pleasurable motoring. Sincerely,
MAHINDRA & MAHINDRA LTD.

1.2 Safety Symbols

Carefully read, understand and follow the safety symbols/ instructions given in this manual.

To emphasize information and procedures regarding safety, use, maintenance, etc., the following symbols are used throughout the manual.

1.3 General Safety Information and Instructions

Failure to follow the warnings and instructions provided in this manual could result in failure of the vehicle, an accident and/or serious personal injury.

1. Carefully read, understand and follow the warnings and instructions given in this manual. This manual is an essential part of the product. Keep it in a safe place for future reference
2. First-aid kit placed in the glove box of the vehicle. Ensure it is not taken out of the vehicle at any point in time.
3. Please note that throughout this manual, reference is made that “an accident” could occur. An accident could cause you or a bystander to sustain severe personal injury, or result in property damage
4. Never use a mobile phone, personal music device or pager while driving. This may take your focus off the road and lead to accidents
5. Please be advised that many service and repair tasks require specialized knowledge, tools and experience. General mechanical aptitude may not be sufficient to properly service or repair your vehicle. If you have any doubt whatsoever regarding your ability to properly service or repair your vehicle, please contact your Authorized Mahindra Dealer or a qualified mechanic
6. Inspect the seat belt system periodically, checking for cuts, frays or wear in the seat belt webbing, or loose buckles, retractors, anchors or other loose parts. Damaged parts must be replaced immediately
7. Always start and operate the engine in a well-ventilated area. If in an enclosed area, vent the exhaust to the outside. Do not modify or tamper with the exhaust system
8. Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread and check sidewalls for any cuts, cracks, or other signs of wear. Replace as necessary
9. Always maintain the safety labels affixed to your vehicle in a good legible condition
10. All signal lamps, buzzers, shields, guards and other protective safety devices must always remain in place and in good, proper working condition
11. The life span of Mahindra products depend on many factors. Improper use, abuse or harsh use in general may compromise the integrity of the vehicle and significantly reduce its life span. The vehicle is also subject to wear over a period of time. Please have your vehicle regularly inspected by an Authorized Mahindra Dealer or a qualified mechanic. If the inspection reveals any damage or excessive wear, immediately replace or have the component serviced
12. We recommend that you use only genuine parts supplied by Mahindra. The use of non-Mahindra parts will not be covered by warranty
13. Never crawl under or be in close proximity to the vehicle when it is lifted off the ground (by a jack), unless the vehicle is properly supported with jack stands, wheel chocks and other appropriate safety devices
14. Never attempt any repairs or adjustments to any component while the vehicle is in motion. Always switch off the engine, and wait for the engine to come to a complete stop before performing any repairs or adjustments
15. The vehicle identification plates are the only legal identification reference, hence it is necessary to keep them in good condition. Never modify data on the plates or remove them. The customer is responsible for any possible tampering with the plates, which will immediately void the warranty
16. Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control. When the vehicle is fully loaded, drive at a slow speed, especially when turning. Note that the center of gravity of the vehicle increases as the vehicle is fully loaded on the roof carrier

1.4 To Owner’s of a Mahindra Vehicle

When first driving the vehicle after long periods of non-use, you may experience a temporary drive disturbance. This is a characteristic of the tires and should be no reason for concern. The condition should correct itself within 5-15 kms. of driving. If the disturbance persists, have the tires checked by an Authorized Mahindra Dealer.

Your driving ability can be seriously impaired by alcohol even if the blood alcohol level is far below the legal minimum. Drunken driving is one of the most frequent causes of accidents.

Your driving ability can be seriously impaired through the use of prescription or non-prescription drugs or medication (even cough syrup). If you are taking any sort of drug or medication, be sure that it will not affect your driving ability.

Use of electrical devices such as mobile phones, computers, portable radios or other by the driver while driving is dangerous. Dialing a number on a mobile phone while driving also ties up the driver's hands. Use of these services will cause the driver to be distracted and may lead to a serious accident. If a passenger is unable to use the device, pull off the right-of way to a safe area before use. If use of a mobile phone is necessary despite this warning, use a hands free system to at least leave the hands free to drive the vehicle. Never use a mobile phone or other electrical devices while the vehicle is moving.

Please comply with the legal regulations concerning the use of communication equipment in vehicles in your country.

When you are driving over long distances, follow these tips so that you have a safe journey;

• Lack of sleep or fatigue may impact your ability to drive safely.
• Exercise your eyes by shifting the focus of your eyes to different parts of the road.
• Use stimulating beverages such as coffee or tea.
• Relax and stay calm.
• Take breaks at regular intervals.

All of us should play our part in protecting our environment. Judicious vehicle usage and ensuring hazardous waste disposal (including cleaning and lubrication fluids) are important steps towards this initiative.

Mahindra vehicles confirm to existing emission norms (standards). Adhering to the periodical maintenance schedule and using Mahindra genuine parts will help retain emission performance of the vehicle and is a pre-requisite to emissions warranty coverage.

If you have any questions concerning the proper use or maintenance of your vehicle, please call your Authorised Mahindra Dealer. A list of dealers can be found in the Dealer Directory Supplement or on the Internet.

Alternatively, you can contact us on 1800-209-6006 / customercare@mahindra.com.

Driving smoothly during first 1000 kms. will help to prevent premature failures and abnormal system wear improving the life of drivetrain and vehicle components.

A new engine may consume more oil during the first 1000 kms. of running. This should be considered as a normal part of break-in and not interpreted as any problem with the engine.

Mahindra uses high quality parts for building vehicles.

In the event that any parts need replacement, we recommend that you use only Mahindra genuine parts.

Non-Mahindra parts may harm vehicle performance and will not be covered by your Mahindra warranty.

To avoid counterfeit parts and to protect our brand image, Mahindra genuine parts are packed in a branded carton. Look for the “Mahindra Genuine Parts” logo.

Any unauthorised modifications or alternations th this vehicle or failure to use appropriate specification and quality spare parts could seriously affect vehicle roadwothiness and safety leading to an accident, resulting in serious injury.

A wide selection of quality accessories are available through your Authorised Mahindra Dealer. These accessories have been specifically engineered to allow you to personalise your vehicle to suit your requirements and complement its style and aerodynamic appearance.

Each accessory is made from high quality materials and meets Mahindra's rigid engineering and safety specifications. Every Mahindra accessory installed according to the Mahindra installation provisions comes with the respective accessory warranty.

Consult your Authorised Mahindra Dealer for detailed information about accessories available for your specific model variant.

For maximum vehicle performance and safety considerations, always keep the following information in mind:

• When adding accessories, equipment, passengers and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front and rear axle. Consult Authorised Mahindra Dealer for specific weight information.
• Bull bars and nudge guards are not recommended for variants with an airbag.
• Accessories causing any change in vehicle specifications like wheel rims, bull bars, etc., may affect the performance of safety systems.
• Mobile communication systems such as two-way radios, telephones and theft alarms that are equipped with radio transmitters and installed in your vehicle should comply with the local regulations and should be installed only by a your Authorised Mahindra Dealer.

When leaving your vehicle unoccupied:

• Always remove the ignition key when you park the vehicle
• Close all the windows completely and lock all the doors
• Do not leave any valuables in your vehicle. If you must leave something in your vehicle, hide them and securely lock all the doors

1.5 Audio/Infotainment Manual

Please refer the Audio/Infotainment manual available in the manual pouch for details regarding:

• Audio/Video functions
• Bluetooth functions
• Navigation (if equipped)
• Map upgradation details

To upgrade the maps in your navigation system (if equipped), please refer the Infotainment manual.

2.1 Feature Matrix

We recommend you to contact the nearest Mahindra dealer for latest features applicable to your vehicle.

2.2 Dimensions

2.2.1 Front View

2.2.2 Rear View

2.2.3 Side View

2.3 Lubricants and Capacities

2.4 Bulb Specification

2.5 Fuses and Relays

A fuse is the most common electric protection device. A fuse is placed in an electrical circuit, so that when current flow exceeds the rating of the fuse it blows off.

The element in the fuse melts, opening the circuit and preventing other components of the circuit from being damaged by the over current. The size of the metal fuse element determines the rating. Once a fuse blows off, it must be replaced with a new one.

Switch the ignition and all electrical equipment OFF before touching or attempting to change a fuse.

2.5.1 Engine Compartment Fuse Box

Engine compartment fuse box is located adjacent to vehicle battery. Release the lock to access the fuse box contents. Remove the fuse box cover by pressing the clips from both sides using both hands simultaneously. Spare fuses are provided in the fuse box for replacement of blown fuses. Ensure the correct rating fuse is replaced with the blown fuse.

2.5.2 Instrument Panel Fuse Box

Fully open the driver door and slide the driver seat backwards. The main central fuse box is located on the right side of the instrument panel. Price out the securing cover to access the fuse box.

2.5.3 Floor Fuse Box (If ewuipped)

The floor fuse box is located under the LH A-Pillar lower trim.

2.6 Flat Tyre

In case of a flat tyre during driving, reduce your speed gradually, keeping a straight line. Move cautiously off the road to a safe place well away from traffic. Park on a level spot with firm ground. Stop the engine and turn ON your hazard warning flashers.

Firmly apply the parking brake. Have everyone come out of the vehicle on the side away from traffic.

Lifting a vehicle to change a tyre or perform maintenance is very dangerous if you do not have the requisite tools, safety equipment and training. The jack provided along with the vehicle is to be used only for changing a spare tire. It is never to be used to perform any other maintenance or repair on the vehicle.

Find level, solid ground that is clear of oncoming traffic. If you cannot find a safe place to stop, it is better to drive on a flat tyre and damage the rim than it is to risk being hit by oncoming traffic.

After changing a flat tire, never store the tyre or other equipment in the passenger compartment of the vehicle. This loose equipment could strike an occupant in the event of a sudden stop or collision. Store all of these items in the proper place.

2.6.1 Tool Kit

The tool kit is located behind the third row seats on the floor.

The tool kit consists of the following tools packed in a PVC tool bag;

• Assembly Screw Jack
• Jack Operating Lever
• Wheel Spanner
• Tow Bar
• DEO Spanner 10mm x 12mm
• Screw Driver

The warning triangle is located on the rear door trim below the camping lamp. Rotate the two securing knobs and lower the hinged cover. Un-strap the two holding belts and remove the warning triangle pouch.

2.6.2 Spare Wheel Removal

Spare wheel is located below the floor at the rear end of the vehicle. It is held in place by a securing nut underneath the rear luggage compartment floor carpet.

• Locate the plug covering the securing nut below the rear luggage compartment floor carpet. Remove the plug using a coin.

• Loosen the securing nut counter clockwise to winch down/lower the secured spare wheel to the ground.
• Rotate the securing bracket counter clockwise and remove it out of the spare wheel hub
• Remove/pull away the spare wheel

To remove the wheel cover, wrap the tip of a screw driver with cloth, insert it near the lugs of the wheel cover and pry the cover away from the wheel.

2.6.3 Wheel Nut Loosening

Always loosen the wheel nuts before raising the vehicle. Turn the wheel nuts counter clockwise to loosen. To get maximum leverage, fit the spanner to the nut so that the handle is on the right side. Grab the spanner near the end of the handle and push down on the handle. Be careful that the spanner does not slip off the nut. Do not remove the nuts, but loosen them by one or two turns.

Block the wheel diagonally opposite the flat tyre to keep the vehicle from rolling when it is jacked up. When blocking the wheel, place a wheel block in front of one of the front wheels or behind one of the rear wheels.

2.6.4 Jacking

Locate the jack points in the front or rear as needed. They can be identified by a slot used to fit the jack precisely.

Position the jack at the correct jacking point. Make sure the jack is positioned on a level and solid place.

To raise the vehicle, insert the jack handle end with the jack operating lever, wheel spanner square slot into the jack operating lever and turn it clockwise with the handle. As the jack touches the vehicle and begins to lift, check that it is properly positioned.

Ensure no one is in the vehicle. Raise it high enough so that the spare tyre can be installed. Remember you will need more ground clearance when putting on the spare tyre than when removing the flat tire.

• Use the jack only for lifting your vehicle during wheel changing
• When raising the vehicle, do not place any objects on top of or underneath the jack.
• Do not raise the jack with someone in the vehicle.
• Raise the vehicle only high enough to remove and change the wheel.
• Follow jacking instructions
• Do not start or run the engine while your vehicle is supported by the jack.

Lower the vehicle completely and tighten the wheel nuts using the wheel nut spanner. Turn the jack operating lever counter clockwise using the wheel nut spanner to lower the vehicle, making sure the handle remains firmly fitted onto the jack handle extension. Do not use other tools or any additional leverage other than your hands, such as a hammer, pipe or your foot. Make sure the spanner is securely engaged over the nut. Tighten each nut a little at a time in the diagonally opposite order. Repeat the process until all the nuts are tight.

Put the wheel cover into position aligning the nozzle on the wheel to the nozzle clearance on the wheel cover. Tap it firmly on the sides with your hand to snap it into place.

2.6.5 Restore all the Tools, Jack and Flat Tyre Securely

Replace the tools (jack, wheel spanner, etc.,) in their storage locations.

Align the spare wheel bracket to the centre hub of the wheel. Winch up the flat tyre to the floor at the rear of the vehicle. Firmly tighten the securing nut and put the floor carpet back.

Double check to ensure the tyre is snug against the rear floor of the vehicle. The spare wheel bracket/cable may be damaged if the vehicle is driven with the spare wheel loosely mounted.

Drive slowly to the nearest service station and inflate to the correct pressure. Always reinstall the valve cap after checking or adjusting tyre pressure, dirt and moisture could get into the valve core and cause air leakage or valve damage.

2.7 Technical Specifications

2.8 Vehicle Identification Number (VIN)

Vehicle Identification Number (VIN) is the legal identity of your vehicle. The vehicle identification number is stamped on the VIN plate riveted on to the bottom of the B-Pillar on the driver side.

The engine number is punched on the LHS face of the crankcase adjacent to the water pump. The engine number is also stamped on the VIN plate near the bonnet release lever.

2.9 Engine Number

The engine number is punched on the LHS face of the crankcase adjacent to the water pump. The engine number is also stamped on the VIN plate near the bonnet release lever.

3 VEHICLE OVERVIEW

3.1 Front Overview

3.2 Rear Overview

3.3 Instrument Panel Overview

4 INSTRUMENT CLUSTER OVERVIEW

4.1 Instrument Cluster

4.2 Warning Lamps Overview

Sr No	Symbol	Warning Lamp/Tell Tale	Lamp Pre-check	Lamp Status while Engine running	Action/Remarks
A		Parking Lamp	No	Continuously ON	Indicates Parking Lamp is ON
B		AWD Lamp	No	Continuously ON	Indicates a malfunction of the AWD system. Contact an Authorised Mahindra Dealer Immediately
C		Rear Fog Lamp Indicator *	No	Continupusly ON	Indicates rear fog lamp is ON
D		Left Turn Indicator	No	Slow or Fast Blinking	Indicates left turn lamp is blinking Slow Blinking: Normal operation Fast Blinking: One / more left turn lamp bulb has fused. Have the bulb replaced
E		Airbag Warning Lamp *	For about 2 seconds	Continuously ON	Indicates malfunction of the airbag system. Contact an Authorized Mahindra Dealer immediately
F		Front Fog Lamp Indicator	No	Continuously ON	Indicates Front Fog Lamp is ON
G		Glow Plug Indicator	For about 2 seconds	Continuously ON	Indicates a malfunction in the starting system. Contact an Authorized Mahindra Dealer immediately
H		Vehicle Armed Status Lamp	No	Blinking	Slow Blinking: Vehicle is armed with the remote Fast Blinking/Continuously ON: Indicates a system malfunction. Contact an Authorized Mahindra Dealer immediately
I		Low Fuel Warning Lamp	No	Continuously ON	Indicates fuel level has reached the reserve level. Re-fuel immediately.
J		Water in Fuel	Yes	Continuously ON	Indicates water in fuel filter. Drain the water from filter or contact an Authorized Mahindra Dealer for assistance
K		Right Turn Indicator	No	Slow or Fast Blinking	Indicates right turn lamp is blinking Slow Blinking: Normal operation Fast Blinking: One /more right turn lamp bulb has fused. Have the bulb replaced
L		Cruise Control Indicator *	Yes	Continuously ON	Indicates vehicle is in Cruise mode
M		High Coolant Temperature Warning Lamp	Yes	Continuously ON	Engine temperature very high. Contact Authorized Mahindra Dealer immediately
N		Low Engine Oil Pressure Warning Lamp	Continuously ON till Engine Starts	Continuously ON	Indicates engine oil pressure is low. Check oil level and top-up or contact an Authorized Mahindra Dealer for assistance
O		ESP System Warning Lamp *	For About 2 Seconds	Continuously ON or Blinking	Blinking: Indicates ESC has taken control of the vehicle stability Continuously ON: Indicates a malfunction in the ESC system. Contact an Authorised Mahindra Dealer immediately
P	ABS Warning Lamp	ESP OFF Lamp *	No	Continuously ON	Indicates ESC OFF
Q		ESP OFF Lamp *	No	Continuously ON	Indicates ESC OFF
R		Tiretronics	For About 2 Seconds	Continuously ON or Blinking	Indicates low/high tyre pressure or possible malfunction in Tiretronics. Refer to Tiretronics section in FEATURES AND CONTROL/WHEELS AND TIRES chapter for further details
S		Check Engine Lamp	For About 2 Seconds	Continuously ON or Blinking	Indicates a potential malfunction in the EMS, contact an Authorized Mahindra Dealer immediately
T		Parking Brake ON/Brake Fluid Low Warning Lamp	Yes	Continuously ON	Either one of below conditions- 1. Park Brake might be engaged 2. Brake fluid level might be low 3. Front Brake Pads are worn Contact Authorized Mahindra Dealer immediately for assistance
U		OBD Check Lamp	Continuously ON till Engine Starts	Continuously ON	There is a potential malfunction related to emission system, contact an Authorized Mahindra Dealer immediately
V		Headlamp High Beam Indicator	No	Continuously ON	Indicates Head lamp high beam is ON
W		Stop/Start Lamp	No	Continuously ON or Blinking	Continuously ON: Engine is in auto stop mode Blinking: Stop/Start is about to stop the engine
X		Charging System Warning Lamp	Continuously ON till Engine	Continuously ON	Indicates malfunction in charging system. Contact Authorized Mahindra Dealer for assistance
Y		Door Ajar Warning Lamp	No	Continuously ON	Indicates one or more doors and/or boot/hood are open
Z		Seat Belt Warning Lamp	Yes	Continuously ON	If tell-talee is not turning OFF even after fastening the seat belt, contact an Authorised Mahindra Dealer for assistance
* if equipped / select models or variants only

5 SEATS AND SEAT BELTS

5.1 Front Seats

5.1.1 Sitting in Correct Position

Follow the tips below for a comfortable and safe journey;

• Sit in an upright position with the base of your spine pressed against the seat back
• The driver and front passenger seat head restraint has 5 positions. Adjust it as close as possible to the above specified position, with the top of the head restraint even with the top of your head
• Maintain sufficient distance between yourself and the steering wheel. Maintain at least a ten inch (10") distance from the centre of the steering wheel to your chest
• The top curve of the steering wheel should align with your chin for ideal road visibility
• Adjust your seat and seat back angle such that your wrists rest on the steering wheel
• Ensure your legs are in bent position while fully depressing the clutch pedal.

5.1.2 Front Seat Slide

Move the seat forward or backward by lifting the adjustment lever located under the seat front and release once the desired position is reached.

5.1.3 Front Seat Recline

To adjust the seat back, lift the lever located on the outboard side of the seat, lean back, and release the lever at the desired position. To return the seat back, lift the lever, lean forward, and release the lever.

When returning the rear-reclined seat back to its upright position, make sure you support the seat back while operating the lever.

5.1.4 Front Seat Lumbar Adjustment (if equipped)

Both the front seat backs feature lumbar adjustment. The lumbar contour of the lumbar support can be adjusted by means of the adjusting wheel on the inner side of the seat back.

Properly adjusted lumbar support provides adequate back support essential during long journeys.

5.1.5 Front Seat Height Adjustment

The driver seat height can be raised or lowered to three positions.

To RAISE the seat height, lift the seat height adjust handle while there is no load or prior to occupying the seat. Release the lever once desired seat height is reached.

To LOWER the seat height, lift the seat height adjust handle while seated in the driver seat. Release the lever once desired seat height is reached.

5.2 Power Seat (Driver Side Only) (if equipped)

The power seat provides advanced 6-way electrical adjustments for the driver seat. It is equipped with electrically-operated power slider, power recliner and power height adjustment mechanisms.

The graphics on the switches guide you to the function it has been assigned.

• Power seats will be operated even when the ignition switch is turned to the “OFF” position. However, to prevent battery discharge, operate your seats when the engine is runnin
• Do not use two or more seat adjustment buttons simultaneously. It can damage the motor. Be sure to operate the electric seat button one by on
• Do not forcibly operate any power adjustment switch if the seat comes in contact with other object and cannot be adjusted anymor
• If the power seats are not operational, the seats should be checked and fixed before any drivin

5.3 Head Restraint

The head restraint comprises of the padded portion which contacts your head and is inserted/locked in receptacles on the top of the seat back.

5.3.1 Adjustable Head Restraint

The head restraint comprises the padded portion which contacts your head and is inserted/locked in receptacles on the top of the seat back.

Your vehicle seats are equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of rear collision.

Always align top of the head restraint with the top of your head or as close to it as possible. To raise the head restraint, press the lock knob and pull the restraint up. To lower the head restraint, press the lock knob and push the head restraint down.

The head restraint can be pulled out completely by depressing the locking button while pulling the restraint out.

Align the head restraint shafts over the holes on the seat top and push the restraint straight down till you hear the lock click

Keep the seat back as upright as possible so the headrest is behind, not beneath, and almost touching your head.

5.4 Second Row Seats

5.4.1 Second Row Seat Recline

To change the second row seat back angle, lean forward slightly while raising the recline lever on the top corner of the seat back, lean back to the desired position and release the recline lever. Make sure the recline lever returns to its original position and the seat back is locked in place by rocking the seat back forward/backward.

When returning the rear-reclined seat back to its upright position, make sure you support seat back while operating the lever.

5.4.2 Second Row Seat Folding (Third Row Seat Access)

The second-row seat can be flipped forward to provide more cargo space.

• Lower the second-row seat head restraint to the lowest position (else it will obstruct and hit the floor)
• Insert the lap belt into the pocket of the seat bottom
• Recline the seat back to full forward direction
• Recline the seat back to full forward direction

• Push side actuation lever (B) in forward direction for Ingress, OR
• Pull rear actuation lever (A) for Egress

• Push seat back to rear side of vehicle for locking
• Pull seat back for upright position till it locks in design position
• Push seat cushion downward by sitting on it (>45 kg) for locking seat cushion

5.5 Third Row Seats

Access to or exit from third row seat and luggage area is possible by completely folding the second row seat. Second row seat features 60:40 split configuration. Instead of folding the complete seat back and seat cushion, the required seat alone can be folded to gain access to third row seat.

5.5.1 Third Row Seat Folding

To fold the third row seat, unlock the seat back by pulling the lever on the rear of the seat back outwards.

Similarly lower the other half of third row seat to get a completely flat surface.

Both the second row and third row seats can be folded flat to maximise the luggage space.

5.6 General Warnings and Instruction - Seat Belts

At least once each month, inspect the seat belt webbing for any cuts, tears, or other signs of wear (such as fraying along the edges). Also inspect the anchors, retractors, and buckles to be sure they are tight and operational.

5.6.1 General Warnings and Instructions

• All occupants, including the driver, should always wear their seat belt no matter how short the trip in order to minimize the risk of severe injury in the event of a crash. In an accident, an unbelted passenger becomes a projectile, and can cause serious injury to himself or another passenger.
• In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt
• Some people believe that wearing a seat belt will lead to entrapment in the vehicle after an accident. However, your chances of surviving the initial impact, being able to unbuckle yourself and escaping from the vehicle is much greater if you are belted.
• In order to be properly buckled, you must always sit up straight and keep your feet on the floor in front of you. The lap part must be worn low and tight across your hips, just touching the top of your thighs. While fastening the seat belt, the shoulder strap of the seat belt must pass over your chest and top of your shoulder. It must never touch your neck, face, the side of your shoulder, arm, or pass under your arm. The belt must always be flat against your body and not twisted in any way. Nothing, such as an arm rest, a pocketbook, or any external objects should be between you and the seat belt. Improper wearing of a seat belt will reduce the protection in an accident.
• Seat belts should be adjusted as tightly as possible, consistent with comfort to properly secure the wearer in the seat. A slack belt will greatly reduce protection to the user, and could cause additional injuries.

• The seat belts provided for your vehicle are designed for people of adult size, must be properly used and maintained.
• Passengers should not move out of or change seats while the vehicle is moving. A passenger who is not wearing a seat belt can be thrown against the inside of the vehicle, against other occupants, or out of the vehicle during a crash or emergency stop
• Do not use any accessories on seat belts or modify in any way the seat belt system. Devices claiming to improve occupant comfort or reposition the seat belt can reduce the protection provided by the seat belt and increase the chance of serious injury in a crash
• An accident or emergency stop, can damage your seat belt system, even if the accident is “minor”. Please have your Authorized Mahindra Dealer inspect the seat belt system after an accident
• Please be aware that any unsecured item in your vehicle, such as your pet, unsecured child restraint system, or a laptop, can become a projectile in the event of an accident or sudden stop, causing injuries to occupants in the vehicle

Seat Belts - Patients

Persons with serious medical conditions should also wear a seat belts. Consult your doctor for specific recommendations before travel.

Seat Belts - Pregnant Women

Pregnant women must also wear seat belts. Consult your doctor for specific recommendations.

The lap belt should be worn snugly and as low as possible over the hips. The shoulder belt should be worn across your shoulder, but never across the stomach area. When worn properly, the seat belt will protect both the mother and the fetus in an accident or emergency stop.

Seat belt usage is necessary to:

• Reduce the possibility of being thrown from your
• Reduce the possibility of injuries to lower body and legs during an accident
• Hold the driver in a position which allows better control of the vehicle

Children who are too large for child restraint systems should always occupy the rear seat and use the vehicle seat belts. The lap portion should be fastened snug on the hips and as low as possible and the shoulder strap should be across the child's shoulder, not the neck or face. If you are unable to position the strap across the child's shoulder, the child should remain in a booster seat. Frequently check the seat belt to be sure it remains snug and in position. A squirming child could cause the seat belt to come out of position.

5.7 Fastening the Seat Belt (3-Point type)

Adjust the seat as needed, sit up straight and well back in the seat. To fasten your seat belt, pull the webbing out of the retractor and insert the metal tab into the buckle. An audible “click” would be heard when the tab locks into the buckle. Pull up on the shoulder strap to tighten the lap belt across your hips. The seat belt retractor will pull in any slack in the shoulder strap. A slow and easy motion will allow the belt to extend and let you move your body around freely.

Periodically check the seat belt as you ride to be sure it remains snug and in position. If there is a sudden stop or impact, the belt will lock into position. It will also lock (restrict) if you try to lean forward too quickly.

5.8 Fastening the Seat Belt (2-Point Lap type)

This seat belt is applicable to the second row middle passenger seat. Insert the tongue into the buckle until it snaps. Position the lap belt on the hips as low as possible.

5.9 Unfastening the Seat Belt (both 3-Point & 2-Point)

To release the belt, press the buckle release button and allow the belt to retract. If the belt does not retract smoothly, pull it out and check for kinks or twists. Then make sure it remains untwisted as it retracts.

5.10 Seat Belt Height Adjuster

You can adjust the height of the shoulder belt anchor for maximum comfort and safety in both front seats. If the height of the seat belt is too near your neck, you will not be getting the most effective protection. The shoulder portion of the belt should be adjusted so that it lies across your chest and midway over your shoulder nearest to the door and not your neck.

To adjust the height of the seat belt anchor, lower or raise the height adjuster to an appropriate position while pressing the height adjuster button. Release the button to lock the anchor into position. Try sliding the height adjuster to make sure that it has locked into the position.

5.11 Seating Positions for Child Restraints System (CRS)

Use a child restraint system only if the child is not big enough to properly wear the seat belts. Else, use the regular seat belt instead of the child restraint system. Seat the child in the rear seat and use the seat belt. According to accident statistics, children are safer when properly restrained in the rear seat than in the front seat. Always secure a child in a proper child restraint system in accordance with age and size of the child as recommended by the child restraint system manufacturer.

6 SUPPLEMENTARY RESTRAINT SYSTEM (SRS) (if equipped)

The Supplemental Restraint System (SRS) includes airbags, pretensioners and ECU. The airbags are designed to provide further protection to the vehicle occupants in addition to the primary protection provided by the seat belts and seat belt pre-tensioners.

The primary components of the system are the sensors which measure the crash severity. In the event of a significant frontal impact, the SRS airbags inflate to work in conjunction with the seat belts and help reduce injuries mainly to the driver's or front passenger's head/chest.

6.1 Airbags

• One frontal airbag for the driver (A)
• One frontal airbag for the front passenger (B)
• Two side (seat) impact airbags (C) (if equipped)
• Two curtain airbags (D) (if equipped)

Airbag Location

• In the steering wheel hub - Driver Airbag

• Above the upper glove box - Passenger Airbag

• Outboard side of driver and front passenger seats - Side Impact Airbag

• In the inner roof rail (LH & RH) - Curtain Airbag

6.2 Driver and Front Passenger Air Bag

Your vehicle is equipped with a Supplementary Restraint (Air Bag) System and lap/shoulder belts at both the driver and front passenger seating positions. The indications of the system's presence are the letters “SRS AIR BAG” embossed on the horn pad in the steering wheel and on the passenger side IP pad above the glove box.

The SRS consists of air bags installed under the pad covers in the centre of the steering wheel and the passenger's side front panel above the glove box.

The purpose of the SRS is to provide the vehicle's driver and/ or the front passenger with additional protection than that offered by the seat belt system alone in case of a frontal impact of sufficient severity.

The SRS is designed to deploy the front air bags only when an impact is sufficiently severe and when the impact angle is less than 30° from the forward longitudinal axis of the vehicle.

Front air bags are not intended to deploy in side-impact, rear impact or rollover crashes. In addition, front air bags will not deploy in frontal crashes below the deployment threshold.

6.3 Side Impact Airbag

Your vehicle is equipped with side impact airbag in both the front seats. The purpose of the airbag is to provide the vehicle's driver and/or the front passenger with additional protection during side impacts or collisions.

The side impact airbags are designed to deploy only during certain side-impact collisions, depending on the crash severity, angle, speed and point of impact.

6.4 Curtain Airbag

They are designed to help protect the heads of the front seat occupants and the rear outboard seat occupants in certain side impact collisions.

The curtain airbag are designed to deploy depending on the crash severity, angle, speed and impact. The curtain airbag are not designed to deploy in all side impact situations, collisions from the front or rear of the vehicle or in rollover situation.

6.5 Airbag System Malfunction Lamp

Airbag’s do not require any regular maintenance of service. The airbag system malfunction lamp illuminates when the engine is started, and it turns OFF after about two seconds as self check confirming normal operations of airbag system and malfunction lamp.

This lamp monitors airbag sensor assembly, airbag sensors, indicator lamp, seat belt pre-tensioner's assemblies, inflators, interconnecting wiring and power sources.

If either of the following conditions occur, there is a malfunction of the airbag’s or seat belt pre-tensioner’s. Immediately contact your Mahindra dealer.

• The lamp does not glow when the ignition is switched ON or glows beyond six (6) seconds after switching the ignition ON
• The lamp comes ON at any other time, even briefly

Never make any modifications to your vehicle which could affect the performance of your airbag system. In particular, changes to the vehicle frame, bumpers, bull bar, front fenders, ride height, suspension, seat belts, interior trim, seats or steering wheel (especially covers, pads or other trim), could prevent proper deployment of the airbag. If you need to make any modifications to accommodate any disability you may have, please contact your authorized Mahindra dealer.

Never try to open or strike the airbag cover. If the airbag cover is cracked or damaged in any way, the airbag may not function as intended to. Take the vehicle to an authorized Mahindra dealer.

Even if the airbag’s do not deploy during an accident, take your vehicle to an authorized Mahindra dealer for a thorough inspection of the airbag and seat belt systems, no matter how minor the accident. The airbag system could have been damaged, and may not work as intended in a subsequent accident, resulting in serious injury.

6.6 Airbag Inflation/Deployment

The airbag sensors constantly monitor the forward deceleration of the vehicle. If an impact results in a forward deceleration beyond the designed threshold level, the system triggers the airbag inflators. The deceleration threshold level is low when the vehicle impacts straight into a fixed barrier that does not move or deform. This threshold deceleration will be considerably higher if the vehicle strikes an object, such as a parked vehicle or sign pole, which can move or deform on impact, or if the vehicle is involved in an underside collision. Once the deceleration level is met, a chemical reaction is triggered in the inflators which quickly fills the airbag with non-toxic gas.

Upon deployment, tear seams molded directly into the pad covers separate under pressure from the expansion of the air bags. Further opening of the covers allows full inflation of the airbag’s. A fully inflated air bag, in combination with a properly worn seat belt, slows the driver's or the passenger's forward motion, reducing the risk of head and chest injury.

After complete inflation, the air bag immediately starts deflating, enabling the driver to maintain forward visibility and the ability to steer or operate other controls.

Deployment of the airbag’s happen in a fraction of a second, producing a loud noise releasing smoke and residue along with a non-toxic gas. This does not indicate a fire. This smoke may remain inside the vehicle for some time, and may cause some minor irritation to the eyes, skin or breathing. Be sure to wash off any residue with soap and water as soon as possible to prevent any potential skin irritation. If you can safely exit from the vehicle, you should do so immediately.

• Do not modify, remove, strike or open the seat belt pre-tensioner assemblies, airbag sensor or surrounding area or wiring. Failure to follow these instructions may prevent them from activating correctly, cause sudden operation of the system or disable the system, which could result in serious injury.
• Parts of the airbag module (steering wheel hub, airbag cover and inflator) may be hot for several minutes after deployment. The airbag’s inflate only once.
• Never place objects in front of you or on the dashboard while you are seated in the front seat. You could be injured by the object when it is forced toward you by the inflating airbag.
• Do not cover the steering wheel, instrument panel with any object (e.g. dash panel covers) which may prevent the airbag’s from inflating properly.
• The airbag’s inflate with considerable force. While the system is designed to reduce serious injuries, primarily to the head and chest, it may also cause other, less severe injuries to the face, chest, arms and hands. These are usually in the nature of minor burns or abrasions and swelling, but the force of a deploying airbag can also cause more serious injuries, especially if an occupant's hands, arms, chest or head is in close proximity to the airbag module at the time of deployment. Sit straight and well back into the seat. Move your seat as far back as practical to allow room for airbag inflation, while still allowing you to properly operate/drive the vehicle.
• The driver or front passenger who is too close to the steering wheel or dashboard can be seriously injured during airbag deployment.
• The driver must sit as far back as possible from the steering wheel while still maintaining control of the vehicle.
• The front passenger must sit as far back as possible from the dashboard.
• Sitting improperly or out of position can cause occupants to be shifted too close to a deploying air bag, strike the interior structure or be thrown from the vehicle resulting in serious injury.

• Always sit upright with the seat back in an upright position, on the seat cushion centre with your seat belt on, legs comfortably extended and your feet on the floor.

• All vehicle occupants must be properly restrained using the seat belts.
• All infants and children must be placed in the rear seat of the vehicle and be properly restrained by seat belts or in a child restraint system.
• Front and side air bags can injure occupants improperly positioned in the front seats.

• Even with air bags, improperly belted and un-belted occupants can be severely injured when the air bag inflates. Always follow the precautions about seat belts, air bags and occupant safety contained in this manual.
• Do not modify the front seats. Modification of the front seats could interfere with the operation of the supplementary restraint system sensing components or side impact air bags.
• Do not place items under the front seats. Placing items under the front seats could interfere with the operation of the supplementary restraint system sensing components and wiring harnesses.

6.7 Child Restraint and Airbag’s

6.8 Airbag Deployment

6.8.1 Front Airbag

Front air bags are designed to inflate in a frontal collision depending on the intensity, speed or angles of impact of the front collision.

6.8.2 Airbag Non-deployment

Impacts below a pre-determined moderate threshold may not cause the airbag to deploy in the following cases:

Airbag may not inflate if the vehicle collides with objects such as utility poles or trees, where the point of impact is concentrated to one area and the full force of the impact is not delivered to the sensors.

Running under a truck's tail gate may not provide the decelerations necessary for airbag deployment. Just before impact, drivers often brake heavily. Such heavy braking lowers the front portion of the vehicle causing it to “ride” under a vehicle with a higher ground clearance. Air bags may not inflate in this “under-ride” situation where deceleration forces that are detected by sensors may be significantly reduced by such “under-ride” collisions.

Frontal airbags are not designed to inflate in rear collisions, where occupants are moved backward by the force of the impact. In this case, inflated air bags would not be able to provide any additional benefit.

Frontal impact within 30º range from head-on to the vehicle will not inflate the airbag.

Driving into a big pot-hole, stepped surface or hitting the far side of a hole/incline will not inflate the airbag.

Air bags may not inflate in rollover accidents where airbag deployment would not provide protection to the occupants.

Frontal Side Swipe impact to the vehicle may not provide the deceleration force necessary for airbag deployment. In an angled collision, the force of impact may direct the occupants in a direction where the airbags would not be able to provide any additional benefit, and thus the sensors may not deploy any airbags.

6.9 Airbag Replacement

Self-servicing or tampering with the airbag system is dangerous. An airbag could accidentally deploy causing serious injuries, or will not deploy when there is a need. Always take your vehicle to an Authorised Mahindra Dealer for inspection and repairs

6.10 Self Removing SRS Related Parts

Self removing the instrument panel, steering wheel, seats or airbag related parts or sensors is not recommended. Airbags could accidentally activate and cause serious injuries, or they may not deploy when there is a need. Visit an Authorised Mahindra Dealer if these parts must be removed

6.11 Airbag Disposal

Improper disposal of an airbag or a vehicle with live airbags can be extremely dangerous. Approach an authorized Mahindra dealer to do these jobs.

6.12 Airbag Repair

If the front airbag cover shows signs of damage or having been removed, the vehicle should be towed to the nearest authorized Mahindra dealer for repair. Do not attempt to self repair or reinstall the cover.

6.13 Airbag Maintenance

For cleaning the airbag covers/areas, use only a soft dry cloth or one which has been moistened with plain water. Solvents or cleaners could adversely affect the airbag covers and proper deployment of the system.

7 LOCKS AND KEYS

XUV500 comes with two keys. Your key number is given on the tag attached to the key. It is recommended that you record the key number and store in a safe place. The keys operate all locks in your vehicle including those of the doors and ignition with steering lock. We advise you to keep one of these keys at a safe place for emergency use, but not in the vehicle.

Press the key release button on the RKE to unfold the key.

7.1 Doors

7.1.1 To Open a Door from Inside

Pull the door lever away from the door and push the door outward to open.

7.1.2 To Open a Door from Outside

Pull the door handle firmly outwards to unlock and swing the door open.

7.1.3 Locking/Unlocking Individual Doors from Inside

Individual doors can be locked/unlocked from inside by the respective door lock tabs. Lift the lock tab outwards to unlock or press the tab inwards to lock that particular door.

7.1.4 Manual Locking/Unlocking Doors from Outside

The driver/co-driver door can be manually locked/unlocked from outside by using RKE. Open the key by pressing the key release button on the RKE. The key is bi-directional; you can insert it into the key hole either way. Turn the key anticlockwise to lock or clockwise to unlock the door.

7.1.5 Locking/Unlocking the Back Door

The back door can be manually unlocked by pressing the unlock button under the rear applique.

To close the back door, lower the back door half way down and allow it fall on its own weight. The door is locked automatically

7.2 Central Locking System

All doors of the vehicle can be simultaneously locked or unlocked from the driver door.

7.2.1 Central Locking/Unlocking All Doors from Outside

To manually lock/unlock all the doors from outside using the RKE, turn the key anti-clockwise (A)/clockwise (B) respectively in the driver door key hole.

7.2.2 Central Locking/Unlocking All Doors from Inside

Press the driver door lock tab down (A) to lock or lift the lock tab up (B) to unlock all doors simultaneously.

7.2.3 Child Safety Rear Door Lock

Your vehicle is equipped with left and right side child safety rear door locks. When the lock mechanism is engaged, the rear door(s) cannot be opened from the inside. The door(s) can only be opened from the outside.

To activate the child safety right rear door lock push the lever down (A) till you hear a distinct click indicating the activation of the child lock.

To de-activate the child safety right rear door lock pull the lever up (B) till you hear a distinct click indicating the deactivation of the child lock.

7.3 Remote Keyless Entry (RKE) System

The front side of the RKE has three control buttons; Unlock, Lock and Search buttons. There is also a mechanical key release button (D). The Remote Keyless Entry (RKE) system operates on Radio Frequency (RF). You can insert the key into the ignition with either side up.

7.3.1 Precautions while handling RKE:

• Do not cover the key grip with any material that cuts off RF waves
• Do not leave the key exposed to high temperatures for a long period, such as on the dashboard or hood under direct sunlight
• Do not put the key in any liquid or wash it in an ultrasonic washer

7.3.2 To Lock and Arm the Vehicle with RKE

Press the lock button on the RKE for locking and arming the vehicle. When the vehicle is successfully locked and armed using the RKE, the hazard lamps flash once. If there are any open doors, the hazard lamps flash five times along with audible beeps indicating the same.

• If any of the doors, except the driver door, are open while locking the vehicle with RKE, the vehicle locks all doors (door locks) irrespective of the open door/doors. When the open door(s) is/are closed later, the vehicle is locked and armed.
• If the driver door is open while locking the vehicle with RKE, the vehicle is not locked or armed. Close the driver door and lock the vehicle again with RKE to arm the Anti-theft system.

7.3.3 Unlock and Disarm the Vehicle with RKE

Press the unlock button on the RKE to unlock and disarm the vehicle. When the vehicle is unlocked and disarmed using RKE, hazard lamps flash twice

7.3.4 Theft Alarm

If there was an unauthorized attempt to open/start the vehicle by someone from the time you had locked and armed the vehicle to the time you press the unlock button of RKE, the hazard lamps flash four times along with an alarm indicating the attempt. If this occurs, press the “UNLOCK” button on the RKE to disarm the security alarm.

Press the unlock button on the RKE to cancel the alarm.

7.3.5 Back Door Open

Press the back door open button on the RKE to unlock the back door. The hazard lamps flash four timesindicating the same.

7.3.6 Search Function

The search function can be used to locate the vehicle in a parking lot. Press the unlock button on the RKE for more than 3 sec. continuously to activate the search function.

When the Search function is ON, the hazard lamps flash for approx. 30 sec. helping you to locate your vehicle. To extend the search, press the search button again which will flash the hazard lamps for another 30 sec. You can turn it OFF by pressing the unlock button.

The head lamps also turn ON when UNLOCK button is pressed twice (enabling the LMV feature). For the first UNLOCK command, the doors are unlocked, and for the next UNLOCK command, the head lamps turn ON enabling you to safely board/locate the vehicle in the night.

Search function works both during Locked/Unlocked conditions of the vehicle.

7.3.7 Mute/Un-mute the Alarm/Beeps

The alarm or beeps heard when one of the doors are open can be muted/un-muted. Press the lock button for more than 3 sec. to swap between mute and un-mute.

The beeps heard during the door open situation can be muted/unmuted. There are NO BEEPS during normal locking/unlocking of doors.

7.3.8 Panic Alarm Function

The panic alarm function can be used during emergencies to draw the attention of onlookers/bystanders. Press the unlock button on the RKE for more than 3 sec. continuously when the key is in the ignition to activate the panic alarm.

7.3.9 Auto Locking

When the vehicle crosses 20 kmph road speed range with all the doors closed properly, all doors are locked automatically.

7.3.10 Auto Unlocking

All the doors are unlocked automatically, when the vehicle has halted and ignition switched OFF. If the ignition is not switched ON for the next few seconds, all the doors are locked due to auto locking, provided doors are not open.

7.3.11 Auto Re-locking

Once you press the unlock button on the RKE, if you do not open any of the doors for the next 45 sec., all the doors are re-locked automatically.

In case of an accident/collision where a SRS has been activated (Eg. airbag), all the doors are unlocked automatically.

7.3.12 RKE Operating Range

Using RKE, you can lock/arm or unlock/disarm the vehicle from distances approx. 30ft.(9m).

If there is reduction in RKE range, please follow the steps below:

• Check the distance: The RKE may be too far from the vehicle. Stand closer to the vehicle during rain or bad weather
• Check the location: Other vehicles or objects may be blocking the signals. Take a few steps to the left or right, hold the RKE higher, and try again. Moreover, closeness to a radio transmitter such as radio station tower, airport transmitter, mobile or CB radios may lead to reduction in range of RKE
• Check the RKE battery: See battery replacement procedure, given later in this section
• If the RKE is still not working correctly, contact an Authorized Mahindra Dealer

7.3.13 RKE Battery Replacement

If the RKE operation is inconsistent when any of the buttons are pressed it indicates that the RKE battery is weak. The rear side of the RKE is snap fitted. Using a small screw driver or similar tool, pry or separate the two halves of the casing.

Pull out the batteries and discard the same. Insert two new batteries of 3V type. While fitting the new battery, ensure the positive side of the batteries face up. Align both the halves of the RKE and press to snap fit. Check operation of the RKE.

While prying the RKE case, take care not to damage the battery. Do not touch the battery terminals or contacts.

Do not mix old batteries with new batteries. Replace BOTH the batteries when the RKE operation is weak.

Perchlorate material needs special handling and disposal. Refer to local regulations.

7.3.14 If RKE is Lost

If you have lost the programmed RKE, contact an Authorized Mahindra Dealer for procuring a new RKE.

While programming a new key set, you will have to submit all the keys available with you, to an Authorized Mahindra Dealer.

Please note that there is a limitation (max 2 keys at a time) to the number of keys that can be ordered. The minimum time frame required to supply the duplicate keys is 10 days after all the formalities are completed. Please contact the dealer to understand the formalities involved.

If you make your own duplicate key, you will not be able to deactivate the anti-theft devices or start the engine.

If the key is stolen or lost, communicate to Authorized Mahindra Dealer for de-activating the function of the lost or stolen key. This is essential to avoid unauthorized access using the misplaced key.

Only RKE transmitters programmed to your vehicle electronics can be used for remote locking and unlocking of your vehicle.

7.4 Passive Keyless Entry (Smart Key) / Smart Key System (if equipped)

Passive Keyless Entry (Smart Key) System enables you to enter or exit your vehicle without the need to manually lock/unlock the doors. You can start/stop, lock or unlock the vehicle using Smart Key. To do this, you only need carry the Smart Key with you

The front side of the Smart Key has three control buttons: Unlock (A), Lock (D) and Back door release (C) buttons. There is also a emergency key release button (B), which releases a mechanical key for emergency purposes (E.g. when PKE battery is low). To remove the metal key, press and hold the release button (B) and pull the mechanical key out

Carrying the Smart Key along with you, you can lock or unlock the doors and tail door and even start and stop the engine without inserting the key. Functions of the buttons on a Smart Key is similar to the remote keyless entry

Locking the Vehicle:

• Carry the Smart Key
• Close all the doors
• Press the button in the door handle
• The hazard warning lights will blink once to indicate the locking (5 blinks will be provided if engine hood is open while locking)
• Make sure that the doors are locked by pulling at the outside door handles

Unlocking the vehicle:

• Carry the Smart Key
• Press the button in the door handle
• All doors would unlock and hazard warning lights will blink twice

Unlocking the Tail door alone:

• Carry the Smart Key
• Press the trunk release button in the tail door and pull the tail door
• Tail door would unlock and hazard warning lights will blink 3 times
• On closing the door, tail door would get locked automatically

7.4.1 Engine START/STOP Button

The engine can be started or stopped by the presence of the Smart key inside the vehicle

Upon any fault identification by the system in the start/stop switch, an alert would be provided in the Infotainment system along with a chime for 10 secs. Please visit the nearest Authorised Mahindra Dealer immediately to rectify the problem.

Engine start/stop button positions:

To operate the engine start /stop switch to its intended function, Smart Key should be inside the vehicle

Off:

To turn off the engine, stop the vehicle and press the engine start/ stop button once. Status LED in the engine start /stop button goes OFF to indicate the OFF position

Your vehicle is equipped with electronic anti-theft steering column lock. The steering wheel locks when the engine start/stop button is in OFF position to protect against the theft. The steering wheel locks automatically when the driver door is opened or 30 secs after engine start stop button changes to OFF position. If the steering wheel is not locked properly when you open the driver door and on attempting to lock the vehicle, a warning chirp along with the hazard blinks thrice. Try locking the steering wheel again (by toggling Engine Start/Stop button). If the problem is not solved, we recommend to take the vehicle to nearest Authorised Mahindra Dealer immediately.

ON

To switch ON the ignition, press the engine start/stop button when the switch position is in OFF/ACC without depressing the clutch pedal and with the Smart Key inside the vehicle. Status LED in the engine start/stop button will turn green to indicate the IGN ON position and the vehicle is ready for starting. Status LED colour would change to orange if the vehicle is not started within 30 secs, but the vehicle ignition remains in ON position.

Vehicle ignition would not turn to ON position on any of the following conditions:

• If the electronic steering lock is not getting unlocked

  A warning would be displayed in the Infotainment system along with beep sound for a few secs. If the steering wheel doesn’t unlock properly, press the start/stop button while turning the steering wheel right/left to release the tension on the lock

  Still if you are not able to turn ON the IGN, please contact the nearest Authorised Mahindra Service Centre

  
• Still if you are not able to turn ON the IGN, please contact the nearest Authorised Mahindra Service Centre
• If the key is not detected inside the vehicle or far away from the driver which is not in detectable position

  A warning would be displayed in the infotainment system along with a beep sound for a few secs. Bring the Smart Key inside the vehicle if not in the vehicle or keep the key away from any electronic gadgets to allow the system to detect the key

  If still the key is not detected, the key battery might be low. Press the start/stop button once and while the status LED in the button is blinking green, bring the key fob on top of the start/stop button and hold for few seconds till status LED changes to permanent green. Once start/stop status LED turns green, press Start/Stop button to turn ON IGN immediately

  
• When engine start/stop button is ON or engine is in running condition with vehicle at standstill and if any door is opened, the system checks for the Smart Key. If the Smart Key is not inside the vehicle, an alert in the infotainment screen is displayed along with a chirp for 5 times to indicate key not detected inside
  Bring the Smart Key inside the vehicle or keep the key in the detectable position whenever you are inside the vehicle.

To start the engine, press the clutch and press the engine start/ stop button once with the key inside the vehicle. The engine can be started from any position (OFF / ACC / ON) of the start/stop switch

To turn the engine OFF in an emergency, press and hold the engine start/stop button for more than 2 seconds or rapidly press and release the engine start/stop button 3 times within 3 seconds. On doing so, the vehicle ignition is changed to ACC position

If the vehicle is still moving, you can restart the engine (without depressing the brake pedal) by: pressing the engine start/stop button, pressing the clutch, gear lever in N position

If the key fob battery is low, the key may not be detected. In such a situation, press the start/stop button once while the status LED in the button is blinking green, bring the key fob on top of the start/ stop button and hold it there for few seconds till status LED changes to permanent green. Once start/stop status LED turns green, press start/stop button to turn ON IGN immediately

If key fob battery is detected low by the system, an alert would be triggered while turning OFF the ignition. Change the battery by following the procedure as mentioned in the section for battery replacement.

7.4.2 Vehicle locking/Unlocking in an Emergency Situation

If the Smart Key does not operate normally, you can lock or unlock the doors by using the mechanical key:

• To remove the mechanical key, press and hold the release button in the side of the key fob and pull the mechanical key head
• Insert the key into the keyhole in the door nearer to the door handle. Turn the key towards the rear of the vehicle to unlock and turn it towards the front to lock
• To reinstal the mechanical key, put the key into the key fob and push it until a click is heard

The Smart Key may not work if any of the following occurs:

• The Smart Key is close to a radio station, airport or an area where there is a possibility of large radio transmissions which can interfere with the normal operation of the Smart Key
• The Smart Key is near a mobile or a cellular phone or some electronic gadgets like Laptop/Tablets. The signal from the Smart Key could be blocked by normal operation of your cell phone or smartphone. Avoid placing the Smart Key and your electronic gadgets in the same trouser or jacket pocket or in the bag and maintain adequate distance between the two devices
• Another vehicle Smart Key is being operated close to your vehicle
• Smart Key kept inside the glove box or top bin in the instrument panel may not be detected sometimes. Keep the Smart Key in the visible zone or in your pocket for getting it detected
• Keep the Smart Key away from the water or any liquid. If the keyless entry system is inoperative due to exposure to water or liquids, it will not be covered by your manufacturer’s vehicle warranty

7.5 Smart Key Battery Replacement

If the Smart Key operation is inconsistent when any of the buttons are pressed, it indicates that the Smart Key battery is weak. Follow the below procedure to change the battery in the Smart Key.

7.6 If Smart Key is Lost

If you have lost the programmed Smart Key, contact an Authorised Mahindra Dealer for procuring a new Smart Key

While programming a new key set, you will have to submit all the keys available with you, to an Authorised Mahindra Dealer.

7.7 Engine Immobilizer System

An Engine Immobilizer System is a security system that prevents the vehicle being operated by an unauthorized person. The Engine immobilizer prevents the engine from being started unless it recognizes signals from the correct coded key. When a wrong key is inserted or a theft attempt is detected, the alarm is set off, and the hazard lamps flash along with a siren.

The system is automatically activated when the key is removed from the ignition.

7.7.1 Features of the Immobilizer System:

• Prevents the vehicle being started by anyone not in possession of the correct vehicle key
• The vehicle is automatically protected after the key is removed from the ignition. At every ignition ON, if the vehicle does not recognize the correct key code, the engine check lamp will be illuminate/blink and the engine cannot be started
• The vehicle will not be protected until the key has been taken out of the ignition

If the engine check lamp flashes or remains continuously illuminated after the ignition being switched ON, there is a system malfunction. Contact an Authorized Mahindra Dealer immediately.

Inserting the correct coded key in the ignition and switching the ignition ON, automatically deactivates the system. This enables the engine to start.

In the event of the vehicle not starting with the correct key, switch off the ignition for a minimum of 1 minute and attempt to start the vehicle again.

Do not modify, remove or disassemble the engine immobilizer system. Any unauthorized changes or modifications can affect proper operation of the system and will void your warranty.

The security system will be activated only when the vehicle is locked using the RKE. Locking the doors with the manual key will not activate the security system.

Using the ignition key to open the door, when the vehicle was locked and armed with RKE will be treated as unauthorized by the system setting off the alarm. Press the unlock button on the RKE to cancel the alarm.

8 FEATURES AND CONTROL

8.1 Quadruple Switch

The quadruple power window switch on the driver door armrest/handle controls the following functions;

• ORVM selector
• ORVM adjustment
• Power window functions of all doors in the vehicle.
• Power window safety switch that enables/disables power window operation of other doors when operated independently from the respective doors

8.1.1 Power Windows

Power windows can be operated only when the ignition is “ON” position. The driver can operate all the power windows in the vehicle through the quadruple switch on the driver door armrest/handle. Other passengers in the vehicle can raise or lower their respective window glasses individually by using the separate switches provided on each of the door trim pads/arm rests.

To lower/raise the window glass push/pull the power window switches respectively.

Do not operate the power windows frequently when the engine is OFF. This will drain the vehicle battery.

If you operate the switches often during a short period of time, the system might become inoperable for a certain duration to prevent damage due to overheating. The system will return to normal functioning shortly. It is recommended to operate one window switch at a time.

While operating the power windows, check for obstructions like head, hand, etc. which may lead to personal injuries.

8.1.2 Power Window Lock Switch

The main power window quadruple switch in the driver door trim has a power window lock switch to enable or disable operation of rear passenger and front passenger window switches. To disable the rear or front passenger power windows, press the window lock switch down. To revert to normal operation, press the window lock switch again.

8.1.3 Auto/Express DOWN (driver side only)

Press the driver power window switch down for a moment and release. The glass moves all the way down automatically. You do not need to hold the switch till the glass comes down.

8.1.4 Auto Express UP (Driver Side only) (if equipped)

Pull the driver side power window switch up for a moment and release. The glass moves all the way up automatically. You do not need to hold the switch.

Re-initialisation/Re-calibration of Power Window

Operate the window glass to topmost position and hold the power window switch for 200 milliseconds (minimum). Then, operate the power window to bring the glass to fully down position

8.2 Mirrors

8.2.1 Manual Folding ORVM (if equipped)

Integrated exterior rear view mirrors on both the sides facilitate maximum rear view information to the driver.

Fold both the ORVM’s manually while parking the vehicle in congested roads or narrow parking slots. This avoids hindrances and safeguards the ORVM’s.

8.2.2 Electric ORVM

The ORVM adjustment switch (perimeter switch) and the Left (L)/Right (R) ORVM selector switches are located on the driver door trim/handle.

8.2.3 Interior Mirrors

The interior rear view mirror provides the rear view information to the driver and also aids during reversing.

This mirror has day and night (anti-glare) positions. The night position reduces glare from head lamps of vehicles behind you. Flip the tab (A) on the bottom edge of the mirror to select the day or night position.

8.2.4 Conversation Mirror (if equipped)

The conversation mirror can be used to converse with the rear passengers in the vehicle. Press the mirror cover to lower the conversation mirror. Close the mirror back and press to lock the mirror in position.

8.2.5 Interior Rearview Mirror

The interior rearview mirror provides the rearview information to the driver and also aids during reversing.

This mirror has day and night (anti-glare) positions. The night position reduces glare from head lamps of vehicles behind you. Flip the tab (A) on the bottom edge of the mirror to select the day or night position

8.3 Sun Visor

Sun Visors are provided for both driver and co-driver above the windshield. The sun visors can be used for either frontal or sideward shade, to reduce glare or to shut out direct rays of the sun.

Pull down the sun visor to block the glare of the sun. The sun visor can also be swivelled to the side as shown.

A illuminated vanity mirror (in select variants) is provided on the back of both the driver and co-driver sun visors. Slide the flap/cover to access the mirror. The lamp (A) above the sun visor illuminate automatically when the flap is opened and switch OFF when flap is closed.

The vanity mirror lamp will remain ON as long as the mirror flap/cover is open. This may lead to battery drain if left unchecked for long durations. Ensure the mirror flap/cover is always closed properly before folding back the sun visor in its position.

8.4 Utility Holders

8.4.1 Upper Console Tray

Unlock the console tray cover by unlocking the tray latch (A) and lifting the cover all the way up

8.4.2 Centre Console Storage

Bigger objects, cans, etc., can be stored in the centre console storage. Unlock the centre console cover by unlocking the latch and lift the console cover all the way up.

In select variants, a cooler (air vents) is provided in the centre console storage. You can cool cans, small bottles, etc. by opening the air vents at the bottom floor of the storage. Turn the cooler clockwise to open the air vents, or anti-clockwise to close the air vents

8.4.3 Multi-box Storage

The multi-box is located above the infotainment screen in the centre console. It can be used for storing small items like mobiles, wallets, tickets, etc

To open the lid, gently press the lid. To close, gently press the lid all the way down till it locks.

8.4.4 Center Box

The centre box is located below the HVAC/Switch bank near the gear lever. Small objects like tickets, wallet, etc. can be stored. To open, gently press the centre box lid. To close, gently press the lid all the way down till it locks.

8.4.5 Glove Box

There are two glove boxes on the co-driver side of the instrument panel.

• Upper Glove Box
• Lower Glove Box

The upper glove box can be opened by gently pressing the unlock push button (A). To close, gently lower the glove box lid and press to lock.

The lower glove box is located just below the upper glove box. To open, gently press the unlock push button, and lower the lid. To close the glove box, raise the lid all the way up and gently press to lock the lid.

It is suggested to keep copies of all vehicle documents along with the owner’s manual kit in the glove box for reference when needed.

8.4.6 Cup Holder

The cup holder located in the floor console between the front seats, It can be used for small cups or cans that are closed or have a lid.

8.4.8 Second Row Seat Arm Rest Cup Holder

The second rows seats have an armrest embedded into the seat back. The arm rest can be unfolded and used as a cup holder.

8.4.10 Third Row Cup Holder

The cup holders are located on both left and right side trims below the magazine holder.

8.4.11 Bottle and Umbrella Holder

Bottle and Umbrella holders are located on both the front door lower trims. You can use them to store umbrellas, maps, papers, small books, bottles, etc.

8.4.12 Seat Back/Magazine Pocket

The seat back pockets are located on the back of the front seats for holding light weight papers/books/magazines, etc.

8.4.13 Third Row Magazine Pocket

The third row magazine pockets are located on the trims on either side of the third row seats. They can be used for holding light weight papers/books/magazines, etc.

8.4.14 Grip Handle

Foldable grip handles are provided above the front (passenger only), second row and third row outboard seats.

8.4.15 Coat Hook

The second row outboard passenger seats grip handles feature a coat hook for hanging your coat, shirts, etc.

8.4.16 Sun Glass Holder

Roof mounted sun glass holder is an integral part of the front interior lamp. Press the lid to release the latch and lower the holder. It is strategically positioned to be accessed easily by both the driver and front passenger

8.4.17 Floor Mat(if equipped)

Floor mats are provided in the front and rear foot wells to avoid stains on the floor carpet

8.5 Horn

Press the pad on the steering wheel to blow/sound the horn. The horn functions even when the ignition has been switched OFF.

8.6 Interior Lamps

Interior lamps comprise of front/rear roof lamps, map reading lamps, ambience lamps and ignition key ring illumination. These lamps can be used for an illuminated entry. In auto mode, the roof lamps (courtesy lamps) and ignition key ring illuminate when any of the doors are opened. Once all doors are closed, the interior lamps switch OFF.

8.6.1 Front Roof Lamp

The front roof lamp is located above the interior rear view mirror. The roof lamp can be switched ON by the switch on the lamp.

8.6.2 Map Reading Lamp (if equipped)

8.6.3 Second Row Roof Lamp

The second row roof lamp is located on the roof above the second row seats. The courtesy lamp can be switched ON/OFF by the switch on the lamp.

8.6.3 Roof Lamp Operation

Both the front and second row roof lamps switch has three operation modes to choose from

The roof lamp remains permanently ON in this position irrespective of the door open status

The roof lamp remains in DOOR/AUTO mode in this position.

The roof lamp remains permanently OFF in this position

The operation of the roof lamp in door mode is as follows:

• Roof lamp switches ON, dims and goes OFF after 10 sec delay during RKE unlock
• Roof lamp switches ON when any of the doors is/are open
• Roof lamp dims and goes OFF after 10 sec delay upon closing of all doors
• Roof lamp dims and goes OFF immediately on RKE lock after all doors are closed
• If any of the doors are not closed properly, the roof lamp switches OFF automatically after a preset duration
• Roof lamp goes OFF with ignition ON and all doors closed properly

The roof lamp will be turned ON in the case of an accident in a SRS equipped variant provided the roof lamp switch is in “Door” mode.

8.6.4 Ambience Lamp (Icy Blue) (if equipped)

The ambience lamps give out a light red ambience in the vehicle. They can be switched ON/OFF by the ambience button on the centre bezel switch bank

• Around the front roof lamp

• Under the seat

• Above the pedals in the driver side foot well

• Below the door handle
• Above the bottle holder in the inner door trim

8.6.5 Door Ajar Lamp (if equipped)

The door ajar lamp is present on all four doors. The respective door lamp illuminates when that particular door is open or improperly locked

8.6.6 illuminated Scuff Plates (if equipped)

The illuminated scuff plates are switched ON every time the door is opened. This can also be used as a guide light during ingress or egress.

8.6.7 Camping Lamp (if equipped)

Camping lamp aids you during brief stops in night trips and also while loading/unloading luggage in the rear. It is switched ON/OFF by pressing the switch (A) on the camp lamp

8.6.8 Battery Saver

The battery saver feature helps in switching OFF interior lamps that are inadvertently ON for long durations. This feature works only after the vehicle is locked with the interior lamp ON. If the vehicle is improperly closed/locked, the battery saver switches OFF the lamp after a duration of 3 mins.

8.7 Power Outlet

A 12V power supply socket provided for power take OFF. Electrical equipment/appliances like mobile phone charger, cigarette lighter, etc. can be used in the outlets.

NOTICE

The power sockets function only when the ignition is in ACC or ON positions. It is recommended to use the power sockets when the engine is ON to avoid battery drain.

The power outlet is located in the compartment below the centre bezel switch bank.

WARNING

To avoid serious injury:

• Close the power outlet cap when not in use
• Do not allow children to use or play with the power outlet
• When using electrical appliances, strictly follow the manufacturers instruction manual
• Never use the power outlet for electric heaters while sleeping
• Never insert foreign objects into the power outlet
• Never use malfunctioning electrical appliances
• Never insert inappropriate or badly fitting plugs into the power outlet

Do not modify, disassemble or repair the power outlet in any way. Doing so may result in unexpected malfunction or fire, which could cause serious damage to equipment and/or personal injuries. Contact an Authorized Mahindra Dealer for any necessary repairs.

WARNING

To prevent injuries and accidents, secure all electrical appliances before use. Do not use any appliance that may:

• Distract the driver while driving, or hamper safe driving
• Result in a fire or burn injuries due to the appliance rolling, falling or overheating
• Emit steam, while the windows of the passenger compartment are closed
CAUTION
Use the power outlets only when the engine is running. Remove the plug from the power outlet after using the electric device. Using the power outlets when the engine is OFF or leaving the electric device plugged in for many hours may cause the battery to drain
Do not use the power outlet to connect electric accessories or equipment that are not designed to operate on 12V
Some electronic devices can cause electronic interference when plugged into the power outlet. These devices may cause excessive audio noise and may interfere with other electronic systems or devices in your vehicle

8.8 Instrument Panel Illumination

The instrument panel light intensity can be varied by the illumination control knob located on the RHS near the head lamp levelling switch.

Roll up/down for bright/dim intensity of illumination for the following lighting

• Instrument cluster
• Ambient lamp
• Interior switches
• Infotainment screen/display

8.9 AUX Port

The AUX port is on the left side of CD input slot in the music system interface. You can connect i pods, etc., as an input and listen to the music through the vehicle speakers.

It is recommended to connect an input device only when the vehicle is stationary. Trying to connect an input device while driving may distract your attention and lead to accidents.

8.10 Exterior Lamps

The lighting control stalk is located on the right hand side of the steering wheel and is a part of the combination switch. It controls operations of parking lamps, head lamps, head lamp beam selection, high beam flashing and turn signals when the ignition switch is ON.

8.10.2 Turn Signals

8.10.3 Turn Signal - Right

• Push the lighting control stalk clockwise (to stop position B) to indicate a right turn. The instrument cluster arrow lamp pointing towards the right flashes along with the right side turn signal lamps (front, rear & ORVM) with chime indicating your intention of turning towards right

After you have completed your right turn, the stalk will automatically return to the neutral position switching OFF all the lamps.

8.10.4 Taking a Left turn

• Push the lighting control stalk anti-clockwise (to stop position A) to indicate a left turn. The instrument cluster arrow lamp pointing towards the left flashes along with the left side turn signal lamps (front, rear & ORVM) with chime indicating your intention of turning towards left
• After you have completed your left turn, the stalk will automatically return to the neutral position switching OFF all the lamps.

You can signal a lane change by moving the lighting control stalk clockwise or anti-clockwise to the limit point of free movement of the lever and releasing it once you change the lane.

Rotate the outer rotary switch on the lighting control stalk clockwise aligning the “arrow” on the stalk to “OFF” on the switch to switch OFF all lamps.

Rotate the outer rotary switch on the lighting control stalk clockwise aligning the “arrow” on the stalk to the “1st detente” position on the switch to switch ON the parking lamps.

Rotate the outer rotary switch on the lighting control stalk clockwise aligning the “arrow” on the stalk to the “2nd detente” position on the switch to switch ON the head lamps.

Switch ON the head lamp, and push the lighting control stalk down (away) from steering wheel to switch ON the head lamp high beam or lift/pull the lighting control stalk up towards the steering wheel to switch ON the head lamp low beam. In head lamp high beam, the high beam telltale lamp in the instrument cluster illuminates indicating high beam option selected.

8.10.10 Head Lamp Flash

Pull the lighting control stalk (from the head lamp low beam position) towards the steering wheel to instantaneously flash the head lamp high beam. The head lamp flash works only when the head lamp is OFF or in low beam position.

8.10.11 Auto Head Lamp

The auto head lamp feature works on the outside ambient light intensity input by the RLS (Rain-Light Sensor). Based on this input, the head lamps are turned ON/OFF. For E.g.: This feature will be helpful while driving through a tunnel or poor lit area

The RLS is located behind the interior rearview mirror on the windshield.

To turn ON the auto head lamp feature, rotate the outer rotary switch on the lighting control stalk anti-clockwise aligning the “arrow” on the stalk to the auto head lamp icon on the switch. This is indicated by the auto head lamp tell-tale in the infotainment screen.

To de-activate the auto head lamp, rotate the outer rotary switch on the lighting control stalk clockwise aligning the “arrow” on the stalk to the OFF position on the switch.

8.10.12 Head Lamp Levelling System

When the vehicle is either fully or partially loaded, it may have an upward inclination disturbing the head lamp aiming. A correct head lamp setting provides good visibility to the driver with minimum inconvenience to other road users.

To properly aim the head lamp beam, use the head lamp leveling switch. This switch is located on the right side of the steering column shroud in the instrument panel. This switch has four positions marked as 0, 1, 2 & 3.

Select the suitable switch position depending on the pay load as advised in the table.

8.10.13 Static Bending Lamp (if euqipped)

Static Bending lamps are available on both the head lamps. The static bending lamp assists the driver while taking a turn. It will be activated when the head lamp is ON and steering wheel turned more than 90° at 5 kmph or 45° at 100 kmph speeds.

8.10.14 Fog Lamps (if equipped)

Fog lamps are to be used along with head lamp low beam, to improve the vision during foggy and misty conditions.

8.10.15 Fog Lamps OFF

Align the “OFF” of inner rotary switch on the lighting control stalk to the “arrow” mark on the inner fixed stalk as shown to switch OFF the fog lamps

8.10.16 Front Fog Lamps ON

To switch ON the front fog lamps, first switch ON the parking lamps, rotate the inner rotary switch on the lighting control stalk anticlockwise aligning the front fog lamp icon to the “arrow” on the inner fixed stalk as shown. The rotary switch moves back to its neutral position once released.

The front fog lamp indicator in the instrument cluster indicates the operation status.

8.10.17 Rear Fog Lamp

To switch ON the rear fog lamps, first switch ON the parking lamps, rotate the inner rotary switch on the lighting control stalk clockwise aligning the rear fog lamp icon to the “arrow” on the inner fixed stalk as shown. The rotary switch moves back to its neutral position once released

The rear fog lamp indicator in the instrument cluster indicates the operation status

8.10.18 Puddle Lamp (if equipped)

Puddle lamps are provided at the bottom of the front and rear doors. They are switched ON automatically when either of the front or rear doors are opened. This illuminates the ground below the respective door thereby assisting in a safe entry and exit

8.10.19 Entry Assist Lamp (if equipped)

Entry assist lamps are located on the bottom of both left and right ORVM’s. They provide a illumination outside the driver and front passenger doors when the FMH or LMV features are activated.

8.10.20 Logo Projection Lamp (if equipped)

Entry Assist Lamp logo projection lamps are located on the bottom of both left and right ORVM’s. They provide a illumination of the XUV500 logo outside the driver and front passenger doors as per the following logic

• When the vehicle is unlocked either by remote or through passive entry in the night time, the ORVM unfolds and ‘XUV 500’ Logo projection lamp will be projected in the ground along with lead me to Vehicle function. The logo remains ON for 20seconds or till engine is started, whichever is earlier.
• The logo projection lamp is also switched ON when the engine is shut off in auto stop mode. The logo projection lamp remains ON for 20 seconds or till the engine is restarted, whichever is earlier.
• During exit, the ‘XUV 500’ Logo projection lamp will be projected in the ground along with follow me home function for 20 seconds. The mirror will fold after the logo lamp is switched OFF.

8.10.21 Follow-Me Home (FMH) (if equipped)

This feature helps the driver and passengers to easily get out of the vehicle during poor light conditions. The head lamp low beam and entry assist/logo projection lamps are turned ON for about 20 seconds assisting the passengers to find their way.

To activate FMH:

• Switch OFF the parking lamps
• Remove the ignition key
• Open the driver door
• Head lamp and entry assist lamp switches ON for 20 seconds unless cancelled by UNLOCK signal.

To extend the FMH feature further for 20 seconds, press RKE LOCK button. This FMH extension can be availed for maximum 2 minutes from the first activation.

With FMH mode ON; First LOCK signal received from RKE will lock the doors and subsequent LOCK signal is used to toggle the head lamp ON and OFF.

With FMH mode ON, if UNLOCK signal is received twice from RKE; the feature gets deactivated and cannot be extended further. Also, the doors are unlocked and vehicle disarmed.

8.10.22 Lead Me to Vehicle (LMV) (if equipped)

LMV is the feature that switches the head lamp and entry assist/ logo projection lamps ON for 20 seconds helping the passengers to reach the parked vehicle safely and comfortably at night.

LMV is activated:

• Pressing the unlock button on the RKE under poor light conditions (if vehicle is equipped with auto head lamp)
• Pressing the unlock button on the RKE when FMH was activated while locking the vehicle previously (if vehicle is not equipped with auto head lamp)

LMV is de-activated:

• At the end of 20 seconds after activation
• When any door is opened
• Ignition is switched ON
• LOCK command is received from RKE

To extend the LMV feature further for 20 seconds, press RKE UNLOCK button. This LMV extension can be availed for maximum 2 minutes from the first activation.

With LMV mode ON; First UNLOCK signal received from RKE will unlock the doors and subsequent UNLOCK signal is used to toggle the head lamp ON and OFF.

8.10.23 Hazard Warning Lamp

The hazard warning lamp switch is located in the centre bezel switch bank on the instrument panel.

To turn the hazard warning lamp ON, push the switch in. All the turn signal lamps flash. The instrument cluster turn indicator lamps also flash indicating the same. To turn OFF, push the switch again.

Use the hazard warning lamp when your vehicle is stationary or to warn other road users to be cautious while passing your vehicle.

8.11 Windshield Wipers

8.11.1 Wiper Control Stalk

8.11.2 Wiper Off

The wipe function is OFF when the wiper control stalk is in neutral position (B).

8.11.3 Flick-Wipe (Mist)

Push the wipe control stalk to position (A) for a flick-wipe, hold to operate the wipe continuously (simultaneously lift the wiper stalk towards the steering wheel to operate the wash). The stalk automatically comes back to position (B) when released.

8.11.4 Intermittent (INT) Mode

Intermittent (INT) wiping is selected when the wipe control stalk is pushed down to position C. In the INT mode, the wiper operates on preset intervals.

The delay between each wipe can be varied by rotating the wiper speed intensity rotary switch (F).

8.11.5 Low Speed Wiping

Push the wipe control stalk down to the position (D) to operate the wiper at a fixed low speed.

8.11.6 High Speed Wiping

Push the wiper control stalk down to position (E) to operate the wiper at a fixed high speed.

8.11.7 Auto Wipe

The auto wipe feature works by sensing water (by the RLS) on the windshield. Based on this input, the wipers are turned ON/OFF. For E.g.: this feature will be helpful when the rain is inconsistent.

The RLS (Rain-Light Sensor) is located behind the interior rearview mirror on the windshield.

To turn ON the auto wipe feature, press the outer rotary switch side/edge on the wiper control stalk. This is indicated by the auto wipe tell-tale in the infotainment screen and the wiper performing one single wipe.

The sensitivity of the RLS can be varied by the wiper speed intensity rotary switch (F) on the wiper stalk.

To de-activate the auto wipe, switch OFF the ignition or press the auto wipe switch on the wiper stalk.

8.11.8 Wipe/Wash

Pull/Lift the wiper control stalk towards the steering wheel from any position to activate wipe/wash function. Washer fluid from front washer reservoir is pumped and sprayed onto the windshield. The wipers wipe the windshield 3 times after the washer spray is stopped and wipe once after 5 sec. Hold the stalk in position for continuous spray of washer fluid.

When wiper is in OFF or Interval mode:

After completion of the wipe/wash cycle, wipers return to their bottom position.

If the wipers are in interval mode and DWELL delay is less than or equal to 5 seconds, then the wiper will continue in the interval mode.

If the wipers are in interval mode, and DWELL delay is more than 5 seconds, then a further single wipe will be performed 5 seconds after the wash/wipe cycle. After the drip wipe (last wipe), wiper returns to normal interval wipe.

8.11.9 Rear Wiper

Rotate the outer rotary switch on the wiper control stalk to align the “arrow” on the stalk to the rear wipe “ON” position to operate the rear wiper.

8.11.10 Rear Wash

The rear windshield wash & wipe operates 3 to 4 times or as long as the stalk end is turned/rotated to the rear wash position. Wiping will continue for few seconds after releasing the stalk end switch.

If you switch OFF the ignition before switching OFF the wiper, the blades stop at random on the windshield. Switch ON the ignition and move wiper stalk to 'MIST' position to return the wipers to the park position, provided the wiper stalk is in OFF position.

With the front wipers ON and rear wipers OFF, engaging the reverse gear activates the rear wiper.

There are two nozzles with three adjustable washer jets in the front (below the wipers). Using a pin, the eye ball jets can be adjusted precisely for direction. Always direct the washer jet to hit middle of the windshield. This will enable the wiper blade to wipe the complete width of the windshield.

In the rear, two nozzles with twin adjustable washer jets are provided for the rear windshield wash. Adjust the nozzle to direct the washer jet to hit the middle of rear windshield using a pin. Rear windshield washer fluid is supplied from rear washer reservoir located in the back door.

8.12 Electric Sunroof (if equipped)

A sunroof will make the driving experience more enjoyable by bringing light and sunshine into the vehicle. It provides a real open air feeling along with pure driving fun. With fresh air, your driving experience automatically becomes significantly more relaxed. A sunroof allows air to flow evenly from above the driver, which is much quieter and less intrusive than wind blowing through a side window.

Press the sunroof control lever backward/open (B), both the sunshade and sunroof glass will slide all the way open. To stop the sunroof movement at any point, press the sunroof control glass lever (B) momentarily.

Press the sunroof glass control lever backward/open (B), the sunroof glass will slide all the way open. To stop the sunroof glass movement at any point, press the sunroof control lever (B) momentarily.

With the sunroof open, to close the sunroof glass, press the sunroof glass control lever forward/close (A).

After a vehicle is washed or in a rainstorm be sure to wipe off any water that is on the sunroof before operating it.

Tilt up- The sunroof is tilted up when the Sunroof Glass Control Lever - Forward/Close (A) is shortly pressed (in the sunroof closed condition).

Tilt down/close - The sunroof is tilted down/closed when the Sunroof Glass Control Lever - Backward/Open (B) is pressed (in the sunroof tilted up condition).

Anti-Pinch Function

To prevent any body parts from being trapped by the auto-closing sunroof, an Anti-Pinch Function automatically opens the sunroof when an object is trapped

Wind Buffeting

When you drive the vehicle with the window or sunroof open at a certain position, you may feel some pressure upon your ears or hear some noises similar to those from a helicopter. This happens because of an influx in air through the window or sunroof and its resonance effect. If this happens, adjust by opening the window or sunroof

Battery Discharge/Disconnect or Power Failure while Operating Sunroof

If the sunroof is stopped midway due to a discharged battery or power failure or battery has been disconnected, you need to recalibrate the starting point of the sunroof. In addition, the following cases need the re-calibration

• The sunroof does not completely close or open by operating the switch once
• The sunroof slides back to close. But the operation does not stop even after a complete close and tilts up the sunroof
• The opening gap remarkably decreases for the sliding open or tilt up
• Operation of the sunroof switch does not do anything or work properly

Re-Calibrating the Sunroof Starting Point

• Close the sunroof completely by using the Sunroof Glass Control Lever -Forward/Close (A). Release the lever
• Push the sunroof control lever forward/close in the direction of close (for about 10 seconds) until the sunroof moves a little. Then, release the lever
• Push the sunroof control lever forward/close in the direction of close, until the sunroof operates as follows: The sunshade and sunroof glass slide open → The sunroof glass slide close → The sunshade close
• Release the lever
• When this is completed, the sunroof system has been reset

8.13 Instrument Cluster

The instrument cluster comprises of the tachometer, speedometer, trip meter (A & B), Reset Button, Odometer, Fuel gauge, Coolant Temperature gauge, Warning lamps and Telltale indicators.

8.13.1 Tachometer

The tachometer indicates the real time engine speed in thousands of RPM (revolutions per minute). Each division is 500 RPM. Running the engine in very high RPM leads to excessive engine wear and poor fuel economy. Maintain steady engine speed below 2500 RPM and do not accelerate or decelerate abruptly.

8.13.2 Speedometer

The speedometer indicates the real time road surface speed of the vehicle in kilometers per hour.

The vehicle speedometer is affected by size of the tires used. If the size of the tires are changed from those fitted at the factory, the speedometer might not display the correct road surface speed and distance travelled.

8.13.3 Odometer

The odometer records and displays the total distance traveled in kms. Press the reset button (A) to cycle through odometer and tripmeter displays. Odometer cannot be reset.

8.13.4 Tripmeter and Reset Button

Tripmeter displays the elapsed distance travelled since the last trip reset. There are two tripmeter’s (A/B) which can be reset individually as necessary.

• To select trip A or B, press and release reset button (A) for a second
• To shift from trip A to trip B or vice versa, press and release the reset button (A) again for a second
• While on trip A or B, press and hold the reset button (A) for more than 1 second to reset the respective trip reading to zero\
• Pressing the reset button (A) while in trip B, displays the odometer reading. Again pressing the rest button (A) displays trip A

The engine coolant temperature gauge functions only when the ignition is switched ON. It indicates the instantaneous engine coolant temperature. The coolant temperature varies with changes in weather, load on engine and driving pattern. Temperature rises from Cold (C) (Blue color) to Hot (H) (Red Color).

When coolant temperature reaches the red zone, the high engine coolant temperature warning lamp illuminates.

In such situations switch OFF the AC and observe for any improvements in temperature gauge. If not, stop the vehicle and allow the engine to cool down. Check the coolant level in the coolant reservoir and top-up if required. If the engine is still heating up, contact your nearest Authorized Mahindra Dealer.

Never remove the radiator cap when the engine is hot. The engine coolant is under pressure and could splash on to skin/eyes causing severe burns. Wait for the engine to cool down before adding coolant to the reservoir.

8.13.6 Fuel Level Gauge

The fuel level gauge functions only when the ignition is switched ON. It gives the status of the fuel level in the fuel tank. F indicates the tank is full (70 liters), E indicates the tank in empty.

When the fuel level reaches the reserve, the last 2 bars are displayed. The last bar in the display blinks when the fuel in the tank reaches the low level (approx. 5 liters).

The amount of fuel required to fill the tank up may be less than the specified tank capacity, as a small amount of reserve fuel always remains in the tank.

On inclines or curves, due to the movement of fuel in the tank, the fuel level may fluctuate or the last bar may flash earlier than usual. Always check the fuel level when the vehicle is on level road.

If the last bar flashes even after filling sufficient fuel, contact your Authorized Mahindra Dealer as soon as possible.

8.14 Warning/Telltale Lamps in the Instrument Cluster

8.15.1 Seat Belt Warning Lamp

The seat belt warning lamp illuminates reminding the driver to fasten the seat belt when the ignition is ON. The lamp will continue to illuminate till the driver fastens the seat belt properly.

8.15.2 Turn Lamps

The turn lamp arrows in the instrument cluster flash showing the direction indicated by the turn signals. A sudden increase in the rate of flashing indicates failure of one or more of the lamp bulbs. Have them replaced as soon as possible.

8.15.3 Airbag Warning Lamp

The airbag warning lamp in the instrument cluster illuminates when the ignition is switched ON and goes OFF in about 2 seconds once the engine is running. If the lamp remains ON continuously or flash’s intermittently, contact an authorized Mahindra dealer immediately.

Following conditions indicate airbag malfunction:

• Lamp fails to go OFF after engine is started
• Lamp does not illuminate at all
• Illuminates while driving

Contact an authorized Mahindra dealer immediately when the airbag warning lamp indicates a system malfunction. The airbag may not deploy when needed, which could result in serious or fatal injury, or it might deploy unexpectedly or unnecessarily, which may result in personal injury.

8.15.4 Front Fog Lamp (if equipped)

8.15.5 Low Fuel Warning Lamp

8.15.6 Glow Plug Indicator

8.15.7 Vehicle Armed Status Lamp

Fast blinking indicates a malfunction in the engine immobilizer system. Contact an Authorized Mahindra Dealer immediately.

8.15.8 Rear Fog Lamp (if equipped)

8.15.9 High Engine Coolant Temperature Warning Lamp

Do not continue driving the vehicle with an overheated engine. This may result in engine damage, which will not be covered by the limited warranty.

8.15.10 Water-in-Fuel Warning Lamp

8.15.11 Cruise Indicator

8.15.12 Low Engine Oil Pressure Warning Lamp

Operating the vehicle with the low oil pressure warning lamp ON could cause sudden unexpected engine failure and loss of vehicle control, resulting in an accident and/or serious personal injury.

Do not run the engine with low oil pressure warning indicator ON. This may result in engine damage, which will not be covered by the limited warranty.

8.15.3 ESP System Warning Lamp

While driving, if the ESC system warning lamp blinks, it indicates that ESP has taken control of the vehicle stability. If the lamp remains ON, it indicates the malfunction in the ESP System. Contact the nearest Authorised Mahindra Dealer.

8.15.4 Front Fog Lamp (if equipped)

The front fog lamp telltale indicates the status of the front fog lamp. The front fog lamp can be switched ON only when the parking lamp is ON.

8.15.5 Low Fuel Warning Lamp

When the fuel level in the fuel tank falls below the reserve limit, the low fuel warning lamp is illuminated. Refuel sufficiently and the lamp goes out. If the lamp continues to remain ON even after refuelling, contact an Authorised Mahindra Dealer.

8.15.6 Glow Plug Indicator

When the fuel level in the fuel tank falls below the reserve limit, the low fuel warning lamp is illuminated. Refuel sufficiently and the lamp goes out. If the lamp continues to remain ON even after refuelling, contact an Authorised Mahindra Dealer.

8.15.7 Vehicle Armed Status Lamp

The vehicle armed status lamp flashes intermittently (few seconds frequency) once the ignition is switched OFF and the vehicle security system is armed (when locked using the RKE).

Fast blinking indicates a malfunction in the engine immobiliser system. Contact an Authorised Mahindra Dealer immediately.

8.15.8 Rear Fog Lamp (if equipped)

The rear fog lamp telltale indicates the status of the rear fog lamp. The rear fog lamp can be switched ON only when the front fog lamp is ON

8.15.9 High Engine Coolant Temperature Warning Lamp

The high engine coolant temperature warning lamp flashes when the coolant temperature is above 105ºC. It starts to flash at double the rate when the temperature reaches 110ºC and will be continuously ON with buzzer alert when the temperature reaches 114ºc

The “red” bars in the temperature gauge also flash in the same frequency as the high temperature warning lamp when the above set temperature thresholds are reached

8.15.10 Water-in-Fuel Warning Lamp

The water-in-fuel warning lamp illuminates when the accumulation of water in the fuel filter reaches the maximum permissible limit. The fuel filter needs to be drained. Contact an Authorised Mahindra Dealer

8.15.11 Cruise Indicator

The cruise control lamp illuminates when the ignition is switched ON and goes off in about 2 seconds indicating normal status. The lamp blinks if the accelerator is depressed, while in cruise mode.

When SET+ button in the steering wheel is pressed, cruise control is activated and the lamp illuminates indicating the vehicle is in cruise mode.

When CRUISE OFF button in the steering wheel is pressed, the cruise mode is deactivated and the lamp goes OFF indicating that the vehicle is not in cruise mode.

If the lamp does not illuminate when the vehicle is in cruise mode or does not go OFF when the vehicle is out of cruise mode, there is a possible malfunction in the lamp or the cruise control system. Have the vehicle checked by an Authorised Mahindra Dealer.

8.15.12 Low Engine Oil Pressure Warning Lamp

The low engine oil pressure warning lamp illuminates when the ignition is switched ON and goes off when the engine started. If the lamp remains ON even after starting the engine, or illuminates while driving, stop immediately.

check the oil level after 2-3 minutes. If low, add engine oil to the “MAX” level and check status. If problem persists, contact an Authorised Mahindra Dealer immediately.

8.15.13 ESP System Warning Lamp

While driving, if the ESC system warning lamp blinks, it indicates that ESP has taken control of the vehicle stability. If the lamp remains ON, it indicates the malfunction in the ESP System. Contact the nearest Authorised Mahindra Dealer.

8.15.14 ESP OFF Lamp

The ESP OFF lamp illuminates when the ESP has been switched OFF manually

8.15.15 Tiretronics

The Tiretronics lamp illuminates if there is a tyre pressure or temperature difference in one of the tyres. The Tiretronics lamp blinks (for approx. 75 sec.) and then illuminates continuously when there is a malfunction in the Tiretronics.

8.15.16 Check Engine Lamp

The check engine lamp illuminates when the ignition is switched ON and goes out in 2 seconds indicating normal status. The lamp blinks or illuminates continuously if there is a fault in the engine management system. Switch OFF the engine immediately. Contact the nearest Mahindra dealer for necessary repairs.

8.15.17 Parking Brake Lamp

The lamp illuminates when; Parking brake is engaged or when brake fluid level is low or when front brake pads are worn. If the lamp illuminates while driving, do the following:

• Check if the parking brake is engaged. If yes, disengage it
• Check if brake fluid level is low. If yes, top-up brake fluid to the required level
• If the brake lamp still continues to illuminate, immediately get the vehicle checked at an Authorized Mahindra Dealer.

8.15.18 OBD Check Lamp

The OBD check lamp illuminates when the ignition is switched ON and remains ON till the engine is started indicating normal status. If the lamp remains ON, it indicates a potential malfunction.

There may be a malfunction in:

• The fuel management system
• The emission control system
• Systems which affect emissions

Such malfunctions may result in excessive emissions. Contact an Authorized Mahindra Dealer immediately.

8.15.19 Head Lamp / High Beam Lamp

The head lamp high beam telltale illuminates whenever the head lamps are switched ON to high beam or when the head lamp flash is used.

8.15.20 Stop/Start Lamp

The Stop/Start - Stop/Start lamp flashes when the vehicle/engine is about to stop through the Stop/ Start System. The lamp illuminates continuously when the vehicle/engine has been switched OFF by the Stop/Start System. On restarting the vehicle/ engine again by using the clutch/key, the lamp goes out.

8.15.21 Anti-lock Brake System (ABS) Malfunction Lamp

The ABS malfunction lamp illuminates when the ignition is switched ON and goes OFF after about 2 seconds. If the ABS malfunction lamp continues to remain ON or illuminates while driving (and the brake system warning lamp is OFF), ABS will not operate. But the brake system will still operate conventionally. In this condition, the wheels can lock during severe braking. Have the vehicle checked by an authorized Mahindra dealer as soon as possible.

However, if ABS malfunction lamp and brake warning lamp are simultaneously glowing, there is a severe malfunction in the ABS. Operate the vehicle with extreme care and have the vehicle checked as soon as possible at an authorized Mahindra dealer.

8.15.22 Battery Charging System Warning Lamp

The battery charging system warning lamp illuminates when the battery is not being charged or when there is a malfunction in the alternator.

This lamp illuminates when the ignition is switched ON and goes out as soon as the engine is started. If the lamp continues to remain ON even after starting the engine, it is an indication that the battery is not being charged or there is a malfunction in the alternator. Check the alternator drive belt for looseness/breakage. If the drive belt is okay, switch OFF all unnecessary electrical equipment and recheck. Contact an Authorized Mahindra Dealer for further assistance.

8.15.23 Door Ajar Warning Lamp

The door ajar warning lamp illuminates and the buzzer chimes 3 times when any of the doors including the hood and back door are open during ignition ON. The lamp goes OFF when all the doors are closed properly.

8.16 FASTag (if equipped)

Your vehicle is fitted with a FASTag on front windshield. FASTag may be used for Electronic Toll Collection (ETC). Please connect with www.nhai.org site for updates and understanding.

9 STEERING AND BRAKES

9.1 Steering

Your vehicle is equipped with power steering. Power steering uses energy from the engine to decrease the driver's effort in steering the vehicle. The power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. If for some reason the power assist is interrupted, it will provide mechanical steering capability to steer the vehicle. Under these conditions, you will observe a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.

Upon initial start-up in cold weather, the power steering pump may produce noise for a short amount of time. This is due to the cold, thick fluid in the steering system. This noise should be considered normal, and it does not in any way damage the steering system.

• Never hold the steering wheel to the extreme right or the extreme left for more than a few seconds when the engine is running
• Heavy or uneven steering efforts may be caused by low power steering pump fluid level. Check for low power steering pump fluid level before seeking service by an Authorized Mahindra Dealer
• Do not fill the power steering pump reservoir above the MAX mark on the reservoir, this may result in leaks from the reservoir

• Under inflated tire(s) on any wheel(s)
• Uneven vehicle loading
• High crown in the centre of the road
• High crosswinds
• Wheels out of alignment
• Wheels out of balance
• Loose or worn suspension components

9.1.1 Tilt Steering

The steering wheel can be adjusted for both rake and reach as required using the lever in the steering shroud under the steering wheel.

To tilt/adjust the steering wheel;

1. Pull the tilt lever down to unlock.

2. Raise or lower the steering wheel to the desired position.
3. Pull or push the steering wheel to the desired position.
4. Push the tilt lever back up to its original position to lock the steering.

9.2 Steering Controls - Audio (if equipped)

The steering wheel also houses switches to control the main audio functions.

9.2.1 Steering Audio Operations

• TO TURN AUDIO ON/OFF - Press the mute button for 2 seconds
• SOURCE - Press SOURCE button to toggle between AUX, CD, TUNER & USB mode
• VOLUME CONTROL - Press ‘+’ and ‘-’ button to increase or decrease the volume
• MUTE - Press MUTE button to mute audio while in TUNER and AUX mode and pause the song while in CD, USB mode
• CD USB MODE - Press 'UP' / 'DOWN' button to go to next / previous track

TUNER MODE - Press 'UP' / 'DOWN' button to go to next / previous frequency. Press 'UP' / 'DOWN' button for 2 seconds to AUTO TUNE

9.3 Brakes

Your vehicle is equipped with disc brakes in the front and rear.

Disc brakes offer good braking capability and reduced stopping distance. Wet brake discs result in reduced braking efficiency. After a car wash or driving the vehicle through water, dab the brake pedal while driving to remove the film of water from the brake pads. Brake pads feature wear indicator. When the brake pad is worn, metallic squeal noise is heard indicating the pad wear. Have them replaced immediately.

Driving with wet brakes is dangerous. Stopping distance increases considerably when braking.

Dry the brakes by driving at very slow speed and applying the brakes lightly until the brake performance become normal.

9.3.1 Parking on a Hill/Incline

If you have to park facing uphill, select first gear and turn the front wheels away from the kerb. If you have to park facing downhill, select reverse gear and turn the front wheels towards the kerb. Always ensure the vehicle is in gear and parking brakes is engaged before leaving the vehicle.

9.3.2 Parking Brake

To apply the parking brake, pull the park brake lever up as firmly as possible. When the parking brake is applied with the ignition ON, the brake warning lamp in the instrument cluster illuminates. To release the parking brake, pull the parking brake lever up slightly, press the release button on the lever tip and lower the parking brake lever completely.

• The parking brake should be adjusted as per recommended maintenance schedule
• Always apply the parking brake when leaving the vehicle, and be certain to leave the transmission in gear. Failure to do so may allow the vehicle to roll and cause damage, hit a bystander resulting in serious personal injury
• Leaving unattended children in a vehicle is dangerous for a number of reasons. Children should be warned not to touch the parking brake or the gear lever. Do not leave the key in the ignition. A child could move the vehicle leading to accidents

Engaging the parking brake while the vehicle is in motion can cause the rear wheels to lock up. You could lose control of the vehicle and cause an accident.

Although the parking brake is not recommended to stop a moving vehicle, if the normal brakes fail, the parking brake can be used to stop your vehicle in an emergency. However the vehicle's stopping distance increases greatly affecting the handling of the vehicle adversely.

9.4 Hazard on Panic Braking

Hazard lamps are turned ON during panic braking for 5 secs when the following conditions are met

• Ignition is ON
• Vehicle speed is greater than 80 kmph
• Panic/sudden brake is applied and high deceleration rate is sensed

9.5 Anti-Lock Brake System (ABS) (if equipped)

The Anti-lock Brake System (also called as ABS) is designed to help prevent lock-up of the wheels and stable stopping of vehicle during a sudden, panic emergency braking or braking on slippery road surfaces. The ABS system takes input from wheel speed sensors and brake pedal switch to control the brake fluid pressures at the wheels to avoid wheel lock-up. It allows vehicle to be steered during braking.

The minimum speed for ABS to function is 12 kmph. ABS is activated only during wheel lock conditions where ABS takes over and prevents wheel lock.

During the ABS operation, a slight pulsation may be felt in the brake pedal to indicate ABS is active. You may also hear motor noise from the engine compartment. It is recommended to hold the brake pedal firmly while the ABS is active rather than pumping the brake pedal.

Depressing the brake pedal on slippery road surfaces as on a manhole cover, a steel plate at a construction site, a joint in a bridge, etc. on a rainy day, tends to activate the anti-lock brake system.

The ABS warning lamp lights up when you switch ON the ignition and should go out after a few seconds. If the ABS warning lamp does not go out or if it comes ON while driving, it means there is a fault in the ABS system. In both cases, the normal braking system remains efficient, exactly as on a vehicle without ABS. The vehicle should be examined as soon as possible by an authorized Mahindra dealer.

The Anti-lock brake system is not designed to shorten the stopping distance: Always drive at a moderate speed and maintain a safe distance from the vehicle in front of you. The stopping distance may be longer in the following cases:

• Driving on rough, gravel or snow covered roads.
• Driving with tyre chains installed.
• Driving over the steps such as the joints on the road.
• Driving on roads where the road surface is pitted or differences in surface height.

9.6 Electronic Brake Force Distribution (EBD) (if equipped)

EBD, as a subsystem of the ABS system, controls the effective adhesion utilization of the rear wheels. EBD aids in distributing the brake forces more evenly leading to better vehicle stability during braking.

Typically, the front end carries more weight and EBD distributes less braking pressure to the rear brakes avoiding a lock up/skid.

For example, under light loads EBD applies less effort to the rear brakes and for heavy loads it allows full braking effort to the rear wheels.

A fault with EBD is indicated by illumination of the brake as well as ABS warning lamps. The vehicle should be examined as soon as possible by an authorized Mahindra dealer.

9.7 Hydraulic Brake Assist (HBA) (if equipped)

ESP system recognises / identifies an emergency braking situation from the braking characteristics and thereby achieves a braking output equivalent to a full force demand at the controls. HBA automatically boosts the braking force to the maximum and helps to stop the vehicle as quickly as possible.

10 HEATING, VENTILATION AND AIR-CONDITIONING SYSTEM (HVAC)

HVAC system provided in the vehicle enables occupants to automatically/manually adjust air flow distribution pattern, air flow rate, air intake mode and air temperature inside passenger compartment. By appropriately adjusting the control knobs/switches provided on the HVAC control panel, located on centre console, occupant’s comfort can be ensured. HVAC system also helps in defrosting and defogging/ de-misting the windshield and windows.

Air flow direction can be further controlled by adjusting louvers of air vents. An air filter is provided at the inlet of HVAC blower.

Engine coolant is utilized to heat the cabin air. For cooling the cabin air, an air conditioning circuit based on the vapor compression refrigeration cycle is used. The air conditioning system uses a refrigerant along with a suitable lubricating oil. Although being non-ozone depleting, the refrigerant is a greenhouse gas, hence once allowed to escape in the atmosphere, it adversely affects the environment by contributing to global warming/climate change.

Refrigerant used in system is a hazardous liquefied gas and is under high pressure. The refrigerant is colorless and has ethereal or faint sweetish odor. Exposure of refrigerant to skin or eyes may cause irritation and frostbite. They can also cause suffocation, dizziness and loss of concentration. When mixed with compressed air or certain other refrigerants, it may form flammable mixture. Never try to service HVAC system yourself which would involve refrigerant handling.

Multiple vents are provided for distributing the air, being force-circulated by HVAC blower, throughout the passenger compartment.

To ensure sufficient air flow and hence adequate HVAC system performance, air flow path should be kept free of obstructions. Keep system’s air intake, located near plenum appliqué, free of snow, leaves and other debris. Also keep the area in front of air vents free of any obstruction inside the cabin.

10.1 HVAC Overview

10.1.1 Centre/Side Vents

Two centre vents are located on either side of the infotainment screen in the centre console. The two side vents are located one each at the left and right extreme ends of the instrument panel. Both the centre and side vents provide air flow to the front seat passengers.

Rotate the thumb wheel (B) left to close or right to open the air vent. Direct air to the desired direction by the adjusting louvers (A) up/down or left/right.

10.1.2 Defrost Vents - Side/Windshield

There are four defrost vents in your vehicle; two side defrost and two windshield defrost vents. They are located just below the windshield. The side defrost vents prevent the front windows from de-misting, whereas the windshield A Adjustable Louvers B Thumb Wheel defrost vents help in clearing the mist from windshield.

10.1.3 Second/Third Row Roof Vents

Two (LH & RH) vents for the second row are provided on the B-Pillars. The vents have adjustable louvers to direct the air flow and thumb wheels for vents open/close operations.

The third row vents (LH & RH) are located on side trims on either side of the third row seats.

10.2 Climate Control

There are two types of climate control depending on the variant:

Automatic Climate Control

Manual Climate Control

10.3 Temperature Control

By operating the temperature control knob, temperature of air being discharged from various vents can be adjusted to the desired level. Engine coolant is utilized to heat whereas the air conditioner is used to cool the air inside the AC unit. Based upon selected position of the temperature control dial, the desired discharged air temperature can be obtained.

By rotating the dial counter-clockwise and setting it to the extreme left position, cool air is discharged.

When the dial is rotated clockwise, the discharge air progressively starts getting warmer.

By rotating the dial further in the clockwise direction and setting it to the extreme right position, hot air is discharged.

10.4 Blower Speed Control

Blower force-circulates air through the HVAC unit and distributes it throughout the passenger compartment.

To increase the blower speed, rotate the control dial clockwise (B) and to reduce the blower speed, rotate the dial counter clockwise (A).

To switch OFF the blower, rotate the dial to “0”.

A blower control is provided below the third row (RH) vent to control the air flow to the third row vents.

10.5 Economy Button (ECon)

The ECON button turns ON economy mode. During ECON AC operation the system automatically cuts OFF at a higher temperature than normal AC. The operation can be used during mild weather conditions for better fuel efficiency. Comfort level may be compromised during this operation.

LED on the button indicates the status of the button. Press the ECON switch again to turn OFF economy mode.

10.6 Air-conditioner ON (AC ON)

This button turns the air-conditioner ON or OFF. Adjust the temperature control dial as per the temperature requirement. LED on the button indicates the status. Push the button to turn ON/OFF the AC.

When the air conditioner is functioning, air gets cooled and de-humidified before being circulated inside the cabin. In hot weather conditions, it will take a slightly longer time to cool the interior as compared to cooler weather. Fuel consumption will be relatively higher if the vehicle is being driven with the air conditioner ON.

• In certain operating conditions when the engine gets overheated, the engine management system may switch off the air conditioner intermittently.
• The air conditioner should be operated at least for ten minutes once every fortnight, even during winter months. This allows AC system components to get lubricated periodically and ensures optimum system
• During extreme cold weather conditions, the air conditioner may not function until temperature of the air near the evaporator rises above a predefined threshold.
• When air conditioner is ON, moisture is extracted from the air. The resulting condensate is drained off from the vehicle. It is therefore normal, if you see a small pool of water under your vehicle.

10.7 Re-circulation Mode

To set the HVAC system to recirculation mode, press the recirculation mode button. The LED on the button illuminates, indicating the recirculation mode is active.

In this intake mode, the air from inside the passenger compartment will be sucked by the blower and utilized further to ventilate/cool/heat the cabin.

For quick cabin cooling/heating or while driving through dusty/polluted region, re-circulation mode can be selected for short periods. Driving with this mode active may lead to better fuel economy and longer HVAC filter life.

However, running the air conditioner in re-circulation mode for long will make cabin air too dry and oxygen level drops inside cabin turning the air stale. On the contrary, keeping air intake control in recirculation mode for long, with air conditioner switched OFF, will make cabin air too humid and are more likely to become foggy. Hence never drive in recirculation mode for long, shift back to fresh air mode as soon as possible.

10.8 Fresh Air Mode

Automatic Climate Control

To set the HVAC system to fresh air mode, press the fresh air mode button. The LED on this button illuminates, indicating that fresh air mode is active.

In this intake mode, fresh air from outside the vehicle is sucked by the blower and utilised further to ventilate /cool / heat the cabin.

Manual Climate Control

To set the HVAC system to fresh air mode, press the re-circulation mode button again. The LED on this button switches OFF, indicating that re-circulation mode is active.

10.9 Rear AC

The rear AC provides cooling for the third row AC vents. Adjust the temperature control dial as per the temperature requirement. LED on the button indicates the status.

10.10 Auto Mode (Automatic Climate Control only)

The auto mode can be used to control the complete air conditioning operation of the vehicle automatically. The auto mode controls blower fan speeds, air intake mode, temperature and modes (vents) based on the set temperature.

10.11 Air Distribution Mode

Air distribution mode allows you to select the below air flow patterns;

• Face Mode
• Face and Floor Mode
• Floor Mode
• Floor Defrost Mode
• Defrost Mode

Depending on the variant, the operation of air distribution mode changes.

For Automatic Climate Control

Each press of mode switch changes the flow pattern accordingly.

The air distribution inside the vehicle can be chosen by the Mode button.

For Manual Climate Control

Press the required mode button on the switch bank.

10.11.1 Air Distribution - Face Mode

Air is discharged through the centre and side vents on the instrument panel, and through the second row B-pillar vents

10.11.2 Air Distribution - Face & Floor Mode

Air is discharged through the centre, side and foot vents on the instrument panel, and through the second row B-pillar vents.

Corresponding information is displayed on the infotainment screen.

10.11.3 Air Distribution - Floor Mode

Air is discharged through the foot/floor vents on the instrument panel.

Corresponding information is displayed on the infotainment screen.

10.11.4 Air Distribution - Floor Defrost Mode

Air is discharged through the foot/floor vents, windshield vents and side defrost vents on the instrument panel.

Corresponding information is displayed on the infotainment screen.

10.11.5 Air Distribution - Defrost Mode

Air is discharged through the windshield vents and side defrost vents on the instrument panel.

Corresponding information is displayed on the infotainment screen.

10.12 Rapid Cabin Cooling

1. Make sure that all the windows are fully closed
2. Set the blower to maximum speed
3. Fully open the vents and adjust louvers to direct air toward face
4. Set the air distribution control to face mode
5. Set air intake control to fresh air mode
6. Turn the air conditioner ON
7. Set the temperature control dial to extreme left (coolest) position

For faster cabin cooling you can select re-circulated air intake mode initially. Once passenger compartment reaches a comfortable temperature, shift to fresh air mode. Also blower speed and temperature control knob can be re-adjusted as desired.

10.13 Rapid Cabin Heating

1. Make sure that all the windows are fully closed
2. Set the blower to maximum speed
3. Set the air distribution control to foot mode
4. Set air intake control to fresh air mode
5. Set the temperature control dial to extreme right (hot) position
6. For de-humidified heating, switch the air conditioner ON

For faster cabin heating you can select re-circulated air intake mode initially. Once passenger compartment reaches a comfortable temperature, blower speed and temperature control knob can be re-adjusted as desired.

10.14 Front Windshield Defogging/De-misting

Front windshield glass defogger switch is located on the blower speed control dial in the central switch bank. Press the switch once to activate the defogger. The LED on the switch illuminates upon activation. Air is discharged through the windshield defroster vents, side defroster vents and side vents. Air intake mode is switched to fresh air mode automatically. The defogger heats the front windshield clearing the fog/ frost.

Switch OFF the defogger by pressing the switch again as soon as the fog/frost is cleared.

If the windshield defogger switch is not switched OFF manually, it will turn OFF automatically after a pre-defined time, based on ambient temperature.

If you want to switch the defogger ON again, press the defogger switch again.

On second and subsequent activations of the rear windshield defogger in the same ignition cycle, the defogger ON time will be half the duration of the first activation.

10.15 Rear Windshield Defogging/De-misting

Rear windshield glass defogger switch is located on the temperature control dial in the central switch bank. Press the switch once to activate the defogger. The LED on the switch illuminates upon activation and the defogger heats the rear windshield clearing the fog/ frost.

Switch OFF the defogger by pressing the switch once as soon as the fog/frost is cleared.

If the windshield defogger switch is not switched OFF manually, it will turn OFF automatically after a pre-defined time, based on ambient temperature.

If you want to switch the defogger ON again, press the defogger switch again.

On second and subsequent activations of the rear windshield defogger in the same ignition cycle, the defogger ON time will be half the duration of the first activation.

10.16 Points to Remember

• For quickly defogging/de-misting/defrosting outside of windshield, it is advisable to operate the windshield wiper/washer for few times intermittently.
• If snow has deposited on windshield, use ice scraper to remove ice deposited before using wiper.
• In freezing weather, warm the windshield with the defroster before using the windshield washer. Also use a washer fluid having anti-freezing properties. These will help prevent the washer fluid from freezing on your windshield.
• Dirty/contaminated windshield would make misting/ fogging-up worse. Always keep the inside and outside of windshield clean.
• Reduced air flow because of clogged HVAC filter or any other obstructions in air flow path may lead to in-adequate defogging/de-misting/defrosting performance. If air flow seems to have considerably reduced, get the filter cleaned or replaced immediately. Air flow path should be kept free of obstructions.
• Reduced cooling performance from air conditioner may lead to in-adequate defogging/de-misting/defrosting. If cooling effect seems to have dropped considerably, get the air conditioning system checked by an authorized Mahindra dealer.

11 Starting and Driving the Vehicle

11.1 Saftey Tips - Before Starting Your Vehicle

11.1.1 General

• Before starting the vehicle, inspect the inside and outside of the vehicle; look for any damages, leaks, loose parts, foreign objects/debris. Contact an Authorised Mahindra Dealer if required
• Before starting your journey, check the working of all safety devices/components especially brakes, steering, lamps, signals and tyres. In case you suspect any system/devices are not working properly, contact Authorised Mahindra Dealer
• Adjust the seat headrest, steering wheel and fasten the seat belt as described in this manual. Never perform any seat / steering adjustments when the vehicle is in motion
• Start the vehicle only when seated and belted in the driver's seat

11.1.2 Mirror Adjustment

Ensure that the rearview mirror and both the ORVM’s are adjusted for an unobstructed view of the road behind.

11.1.3 Exterior Lamps

Have someone observe and confirm normal operation of all exterior lamps while you work on the controls from the driver seat. Also, check functioning of all lamps in the instrument panel.

11.1.4 Door Latches

Check for positive closing, latching, and locking of all doors, both from inside and outside.

11.1.5 Fluid Leaks

Check the area under the vehicle after an overnight parking for fuel, power steering fluid, brake fluid, engine coolant, oil, or other fluid leaks. If leaks are observed, contact an Authorised Mahindra Dealer.

11.2 Starting the Engine

Make sure all vehicle occupants are properly seated in their seats and have buckled their safety belts. For more information on seat, headrest positioning, safety belts and their proper usage, refer to the “Seat Belts” section in this manual.

PKE If equipped

1. Shift the gear shift lever to Park or Neutral position
2. Apply parking brake
3. Turn the ignition ON by pressing the start stop button
4. Do not press the accelerator
5. Depress the brake pedal. and press the start stop button to start the engine

Non PKE If equipped

1. Shift the gear shift lever to neutral position.
2. Apply parking brake.
3. Turn the ignition ON.
4. Press the brake pedal.
5. Do not press the accelerator.
6. Turn the key momentarily to the START position to crank the engine.
7. Once the engine starts, release the key; it will return to the IGN position.

If the engine still fails to start, contact an Authorised Mahindra Dealer for assistance.The idle speed is controlled automatically and it will decrease as the engine warms up.

Observe the following when the engine is running:

• All warning lamps are OFF
• Low oil pressure lamp is OFF

After idling for a few seconds, release the parking brake, depress the clutch, shift the gear shift lever to 1st gear, release the service brake pedal, drive by releasing the clutch and depressing the accelerator pedal simultaneously

11.2.1 Engine Idling - In Cold Weather

Avoid full throttle operation when the engine is cold and prolonged idling at low ambient temperatures. Long periods of idling may be harmful to your engine. Combustion chamber temperatures can drop so low that the fuel may not burn completely. Incomplete combustion allows carbon and varnish to form on piston rings and injector nozzles. Also, the unburned fuel can enter the crankcase, diluting the oil and causing rapid wear to the engine.

You must fuel this vehicle with Ultra Low Sulfur Diesel. For smooth functioning and reliable operation of the engine during cold weather conditions, use winter diesel for refuelling which is available at filling stations during winter months. Check with your fuel retailer for details.

For sub zero conditions, contact the nearest Mahindra Dealer for recommendation regarding the fuel additive to be used

The recommended engine coolant mixture will work fine till ambient temperatures do not drop below -32ºC approx. For ensuring above performance, it is a must that you use only recommended engine coolant.

11.2.2 Engine Idling

The idle speed is controlled automatically and it will decrease as the engine warms up.

Observe that all warning lamps are OFF when the engine is running.

After idling for a few seconds, follow the below steps to drive away:

1. Release the parking brake.
2. Shift the gear lever to D.
3. Release the brake pedal.
4. Drive by depressing the accelerator pedal.

11.3 Stopping the Engine

Your vehicle is powered by a turbo diesel engine. Before turning the engine OFF, always allow the engine to return to normal idle speed and run for few seconds. This assures proper cooling and lubrication of the turbocharger. This is particularly necessary after any hard driving.

• Keep your right foot on the service brake pedal
• Turn front wheels towards the road curb

• Switch OFF the ignition, turn the key to the steering lock position and remove the key
• Firmly engage the parking brake
• Move the gear shift lever to 1st gear position (reverse gear if parking on an incline)
• Slowly release the service brake pedal
• Lock your vehicle when leaving

11.4 Exhaust Gases

Protection against exhaust gas entry into the vehicles interior is considered in the design of the exhaust system.

• Vehicle exhaust contains Carbon Monoxide, Carbon Dioxide, Nitrogen Oxides, Hydrocarbons and Particulate Matter. These are potential environmental and health hazards
• Avoid inhaling the exhaust gases. Carbon Monoxide is a colourless and odourless gas and can cause unconsciousness or even death
• If the exhaust system is damaged for any reason or you notice a change in the exhaust noise, have the vehicle checked by an Authorised Mahindra Dealer immediately
• Do not start the vehicle in a closed garage or in an enclosed area where ventilation is poor for the exhaust gases
• Since the engine compartment and exhaust system components are hot and can ignite a fire, do not park or leave the vehicle with the engine idling over dry grass, leaves, paper, rags or any combustible material

11.5 Driving Your Vehicle

11.5.1 General Driving Precautions

• Before you drive your vehicle, please read this manual carefully
• Before you start driving, check proper operation of the brakes and steering system
• If, while driving, you hear any strange noise or feel unusual vibration, or if you have any concerns whatsoever, or if any warning lamps illuminate or buzzers sound, park/stop the vehicle in a safe location as soon as possible. Identify the cause and take any necessary remedial action. Contact your Authorised Mahindra Dealer if necessary
• Never overload or improperly load your vehicle
• Always be attentive while driving and follow safe driving practices
• Always maintain the recommended inflation pressure in tyres
• Always drive at a safe speed appropriate for given driving conditions. You must follow the speed limits
• While backing up, keep a constant lookout for people, particularly children, or other obstructions or hazardous material that might be present behind the vehicle
• Avoid loading any items on the roof that will raise the vehicles centre of gravity and make your vehicle more unstable
• Loaded vehicles, with a higher centre of gravity, may handle differently than unloaded vehicles. Extra precautions, such as slower speeds and increased stopping distance, should be taken when driving a heavily loaded vehicle
• Always slow down in gusty crosswinds. Because of its profile and higher centre of gravity, your vehicle is more sensitive to side winds than an ordinary passenger car. Slowing down will allow you to have much better control
• When driving off-road or on rugged terrain, do not drive at excessive speeds, jump, make sharp turns, strike objects, etc. This may cause loss of control or vehicle rollover causing serious injury. You are also risking expensive damage to your vehicle's suspension and chassis
• Maintain steering wheel control at all times, especially on rough terrains. Sudden changes in terrain can result in abrupt steering wheel motion. Make sure you grip the steering wheel from the outside. Do not grip the spokes
• If the vehicle goes from one type of surface to another (e.g. from concrete to gravel/sand/mud/snow) there will be a change in the way the vehicle responds, especially the way it responds to steering, braking and accelerating input
• Be extremely careful when driving on pavements made slippery by loose sand, water, gravel, snow or ice
• If your vehicle goes off the edge of the pavement, slow down, but avoid severe brake or steering application. Ease the vehicle back onto the pavement only after reducing your speed. Do not turn the steering wheel too sharply while returning to the road surface
• It may be safer to stay on the apron or shoulder of the road and slow down gradually before returning to the pavement. You may lose control if you do not slow down or if you turn the steering wheel too sharply or abruptly
• In an unavoidable emergency situation where a sudden sharp turn must be made, turn the steering wheel only as rapidly and as far as required to avoid the emergency. Excessive steering will result in less vehicle control. Additionally, smooth variations of the accelerator and/or brake pedal pressure should be utilised if changes in vehicle speed are called for. Avoid abrupt steering, acceleration or braking which could result in an increased risk of loss of vehicle control, vehicle rollover and/or personal injury. Use all available road surfaces to return the vehicle to a safe direction of travel

11.5.2 Off-Road Driving Precautions

• When driving off-road or on rugged terrains, never overspeed or make sharp turns. This may cause loss of control or vehicle rollover causing serious injury .
• Maintain steering wheel control at all times. Sudden changes in terrain can result in abrupt steering wheel motion .
• Do not drive horizontally or diagonally across steep slopes, your vehicle can tip over sideways. Driving straight up or straight down is preferred .
• Drive cautiously to avoid vehicle damage from concealed objects such as rocks and stumps. You should either know the terrain or map-out your route before driving in the area .
• Always perform a maintenance inspection after each day of offroad driving that has taken you through rough terrain, sand, mud or water.

11.5.3 Driving Through Water

Although your vehicle is capable of driving through shallow water, there are a number of precautions that must be considered before entering the water.

• The ground under the water might not be firm which could result the water being deeper than expected when driving the vehicle through it
• Do not stop or shut OFF the engine while immersed in water. It helps in preventing water getting inside the exhaust pipes
• When backing down a ramp, do not allow the exhaust tail pipe to immerse in water
• Water can wash the grease from wheel bearings, causing rusting and premature failure. It may also enter the differentials, transmission and transfer case, reducing the oil's lubricating qualities. If these are submerged in water, the lubricants should be replaced as required
• Water entering the transmission will cause deterioration in shift quality, locking up of your transmission accompanied by vibration, and ultimately damaging the transmission
• Sand, mud/sludge that has accumulated in brake drums and around brake discs may affect braking efficiency. This may also damage brake system components. Wet brakes cannot stop the vehicle as effectively as dry brakes. Drying can be improved by driving the vehicle slowly while applying light pressure on the brake pedal
• When driving through water, traction or brake capability may be limited. Always perform a maintenance inspection after each day of off-road driving that has taken you through water

11.5.4 Flowing Water

If the water is swift flowing and rising (as in storm run-off) avoid crossing until the water level recedes and/or the flow rate is reduced

The flowing water can erode the streambed causing your vehicle to sink into deeper water.

Determine the exit point(s) that are downstream of your entry point to compensate for drifting.

11.5.5 After Driving Off-Road or through Water

Off-road operation puts more stress on your vehicle than does most on-road driving. Always perform a maintenance inspection after each day of off-road driving that has taken you through rough terrain, sand, mud, or water.

• After going off-road, it is always a good idea to check for damage. Completely inspect the underbody of the vehicle for any damages
• Check for accumulations of plants or bushes. or polyethylene / plastic. These could be a fire hazard. They might also hide damage to fuel lines, brake tubes/hoses, etc
• Inspect all the tubes/hoses and check for any fluid leakages
• Get heat exchangers (radiator and condenser) cleaned
• Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, suspension and brakes. Retighten them, if required, and torque to the values specified in the ‘Repair Manual’
• We also recommend that the vehicle be checked at the Authorised Mahindra Dealer for any water entry into the transmission/ axle or the engine
• If any unusual vibration is experienced, check the wheels for impacted material. Impacted material can cause a wheel imbalance. Get it inspected/corrected as soon as possible
• After driving through deep water, inspect your vehicle fluids and lubricants (engine oil, transmission/transfer case/axle oils) to ensure the fluids have not been contaminated

11.5.5 Driving in Snow

When ESP warning lamp is ON during driving in snow, Shift the TGS to “M” Mode then shift the gear to 2nd /3rd gear Manually. Accelerate the vehicle slowly and drive at reduced speed suitable to road conditions

Contact the nearest Authorised Mahindra Dealer for further assistance

11.6 Tips for Better Fuel Economy

Give due consideration to the points listed below for better performance of vehicle and enhance fuel economy.

• Smooth, moderate operation can yield savings in fuel
• Steady speeds without stopping will usually give the best fuel economy
• Idling for long periods of time may waste fuel
• Anticipate stopping; slowing down may eliminate the need to stop
• Sudden or hard accelerations may reduce fuel economy
• Slow down gradually
• Drive at moderate speeds
• Revving the engine before turning it off may reduce fuel economy
• Air conditioner may reduce fuel economy
• Warming up a vehicle on cold mornings is not required and may reduce fuel economy
• While idling put the gear lever in neutral position
• Resting your foot on the brake pedal while driving may reduce fuel economy
• Combine errands and minimize stop-and-go driving
• Keep tires properly inflated
• Use recommended engine oil. Refer to the Maintenance Section for specifications and capacities
• Follow the recommended maintenance schedule and perform owner maintenance checks recommended
• Heavily loading a vehicle or towing a trailer will reduce fuel economy
• Carrying unnecessary weight may reduce fuel economy
• Adding certain accessories to your vehicle may reduce fuel economy
• Four-wheel-drive operation (if equipped) is less fuel efficient than two-wheel-drive operation
• Driving on flat terrains offer improved fuel economy as compared to driving on hilly terrains
• Close windows during high speed driving for better fuel economy
• It is recommended to refuel in the mornings (cold weather condition)

11.6.1 How to Calculate Fuel Efficiency (Mileage)

• Ensure recommended tyre pressure is maintained
• Refuel your vehicle till the fuel gun at the fuel station is autocut-off
• Reset trip meter to zero
• Drive at a moderate speed for a minimum distance of 150 kms
• Refuel at the same fuel station till the auto-cut-off mode
• Assuming ‘a’ litres of fuel was filled and ‘b’ was the trip meter reading. Fuel Efficiency = b/a kmpl
• We recommend that point no. 2 and point no. 5 should be done in cold conditions (in mornings)

11.7 Ignition Switch

An illuminator ring is provided on the face of the ignition switch to help in locating the ignition switch at night. The ring will illuminate the moment the driver door is opened and will remain glowing till the driver door is closed.

LOCK - This is the ignition and steering lock position. The vehicle circuits and engine is completely switched OFF. The steering wheel is also locked and the key can be removed from the ignition only in this position.

ACC - The steering is unlocked and can be rotated. In this position all electrical circuits are enabled. Use this mode when you want to listen to music, etc., with the engine temporarily switched OFF.

ON - All electrical circuits are enabled. Some of the warning or information lamps illuminate in this position. While some of the lamps will go out after a few seconds, some will continue to remain ON till the engine is started. When the vehicle is being driven, ignition switch remains in the ON position.

START - This position is to start the engine by cranking the starter motor. This is a momentary position. When the key is turned to start position, the starter cranks the engine. Once the engine is running, release the key, and the key reverts back to ON position and the starter motor disengages from the engine.

11.8 TRANSMISSION

The first few shifts on a new vehicle may be somewhat rough. This is a normal phenomenon, and precision shifts will develop within the initial few hundred kilometers of running.

11.8.1 Gear Selector Lever

Your XUV500 is equipped with 6 speed automatic transaxle having electronic controls with an Adaptive Transaxle Control Strategy. This Adaptive Transaxle Control Strategy offers optimal transaxle operation and shift quality in different driving conditions. The transaxle electronics are self calibrating; therefore, the first few shifts on a new vehicle may be somewhat rough. This is a normal phenomenon, and precision shifts will develop within the initial few hundred kms of running.

1. P : Park position
2. R : Reverse position
3. N : Neutral position
4. D : Drive position
5. M : Manual Shift

11.8.2 P:Park Position

Use this position to park your vehicle, warm up the engine, or stay in a location for an extended length of time.

To shift into any other position, first depress the brake pedal. Then move the TGS to D or R as desired.

11.8.3 R: Reverse Position

Use this position to reverse the vehicle.

To shift into “R” from “P” or “N”, completely stop the vehicle and depress the brake pedal. When the shift lever is in “R”, parking aid system will be automatically activated.

11.8.4 N: Neutral Position

At this position, the engine does not transfer power to the wheels and the vehicle will not move on a flat road. However, for safety, apply the brake when the gear is in this position.

11.8.5 D:Drive Position

Use this position for normal driving conditions. The transaxle is automatically shifted from 1st gear up to 6th gear according to the level of depression on the accelerator pedal

11.8.6 M: Manual Shift

Driving gear can be adjusted by operating the tip switch after moving the gear selector lever from “D” to “M” position

In Manual shift mode, the user can upshift or downshift from 1 to 6 forward gears by moving the plus / minus switch, present in the gear shifter knob

Shift up: Move the knob switch forward in the plus direction and release once to shift up one gear.

Shift Down: Move the knob switch backward in the minus direction and release once to shift down one gear.

The gears can be shifted without requiring to release the Accelerator pedal.

In manual mode, downshifts are made automatically when the vehicle slows down. Similarly, upshifts are automatically made when the engine rpm exceeds the threshold.

When starting to drive on a snow or icy road, upshift of the gear to 2nd or 3rd is possible to avoid loss of traction.

When the shift is demanded the gear position indicator will blink to acknowledge the request. The actual demanded gear will be shown after the shift has been completed.

For safety reason maximum three shifts “+”/ ”-” can be allowed at given point of time.

Use of Engine Brake

To use the engine as a brake, change into the manual gear shift mode first, then operate the tip switch to next lower gear

11.8.7 Ignition Key Interlock system (If equipped)

The Ignition Key cannot be removed from the key barrel unless the shift lever is in the P (Park) position

• If the key is stuck in the key barrel due to any electric malfunction, press the Emergency Key release Switch located to the left of the driver foot-well lamp to release the key. Contact Authorised Mahindra Service Center at the earliest
• Always start the engine while the selector lever is in P & N with Brake pedal depressed

11.8.8 Gear Shift Interlock System

The Automatic Transaxle has a shift lock system which prevents shifting the transaxle from P or N into R unless the Brake Pedal is depressed

In case of malfunction of the Shift Lock system, press the Shift-Lock override switch as shown in the image, to move the shifter. Contact Authorised Mahindra Service Center at the earliest

11.8.9 Starting and Driving Off

1. Always start the engine while the selector lever is in “P”. For your safety, avoid starting the engine from “N” even though you can do so.
2. Check whether or not the engine idling speed is normal. Keep the brake pedal depressed and shift into “D” or “R”.
3. To move the vehicle, release the brake pedal and depress the accelerator pedal gradually.

11.8.10 Creep Function

Without any actuation of the accelerator pedal, your vehicle will move slowly if the selector lever is in any position other than “P” or “N”. This is called the creep effect. You can control your vehicle’s movement by only applying the brake in heavy traffic or narrow areas.

11.8.11 Kickdown Function

If you need to accelerate rapidly, depress the accelerator pedal to its travel end. Then, a lower gear will be automatically engaged. This is called the kickdown function

11.8.12 Engine Braking

When the accelerator pedal is released while the vehicle is in motion, the engine speed decreases. On a down hill, engaging a lower gear can generate a higher engine braking and eventually slow down the vehicle speed. By using engine behavior as a brake, you can decrease your vehicle speed without excessively using the brake system. The lower gear, the higher braking force.

11.8.13 Gear Indicator

The current gear lever position is indicated in the centre of the speedometer dial.

11.8.14 Neutral Position

This position stops the transmission of power from the engine to drive axle. With the gear lever in neutral and brakes released, the vehicle can move freely by pushing or towing. The engine can be started in this mode. It is always recommended to keep the brake pedal depressed in this position. It is advisable to shift into neutral when the vehicle is standstill for longer durations with the engine idling.

11.9 Limp Home Mode(LHM)

When there is a malfunction in the transaxle, it goes into Limp Home Mode to maintain minimum driving conditions and also to prevent critical transaxle damage. This status is indicated by the transaxle check lamp illumination in the instrument cluster. Contact the nearest Authorised Mahindra Dealer for further assistance

11.10 Safety Mode

When the transmission has an electrical or mechanical fault, the transmission operates in the safety mode to maintain minimum driving conditions and to prevent the transmission from being damaged

When the transmission is defective, the symptoms that can occur are as follows

• Heavy shock when moving the selector lever
• Decreased driving force while driving at high speed
• Fixed gear position during driving (cannot accelerate the vehicle)

If you find any symptoms caused by mechanical or electrical defects in the transmission, stop the vehicle immediately and reset the safety mode.

If abnormal operation of the transmission (fixed at the 3rd or 5th forward gear in “D” or reverse gear in “R”) still exists, have the system checked by a Mahindra dealer.

If the mechanical or electrical problem still exists, have the system checked by a Mahindra dealer.

Resetting the Safety mode when the Gear is fixed

How to reset the safety mode:

• Park the vehicle and place the selector lever to “P”.
• Stop the engine and switch off the Ignition and take out the key
• Wait for 30 seconds and do the Ignition On and Start the engine.

Symptoms after resetting the safety mode

1. If the vehicle operates normally after resetting, the problems gets rectified
2. If, still the gear is fixed at the 3rd or 5th forward gear in the “D” position or the reverse gear in “R” position, have the system checked by a Mahindra dealer.

11.11 All Wheel Drive (AWD) Operation (if Equipped)

In an AWD vehicle, power is transmitted to all the wheels. This is managed by the AWD System which intelligently transfers torque to all four wheels. AWD system includes electromagnetically operated clutch which is controlled by an ECU. According to the driving conditions, this system automatically delivers torque to the rear wheels

11.13.1 AWD System

AWD system is available in two operating positions viz., AUTO mode and AWD LOCK mode.

Once the ignition key is turned ON, AWD system by default turns into AUTO mode. In AUTO mode, whenever a slippage is detected in the FRONT wheels (slippery surfaces like icy roads, wet surfaces, etc.) the torque is transferred to the REAR wheels by the AWD system.

11.13.2 AWD Lock

AWD LOCK button is located on the central bezel switch bank. The LED on the switch turns ON when the AWD Lock is activated. In this mode, fixed amount of torque is transferred to the rear wheels irrespective of the driving condition

11.12 Hill Descent Control (HDC) (If equipped)

Assists the driver to descend a steep hill (max. 50% inclination) by means of brake intervention limiting the vehicle speed is without driver's input.

During HDC, if the wheel slip becomes excessive, ABS will be activated automatically.

HDC is a user-intended function. To activate, press HDC button on the central bezel switch bank. The LED on the button illuminates indicating the status. Press the button again to deactivate HDC.

During a descent, if the vehicle speed is more than the rated speeds (refer recommended shift speeds), HDC (if selected) automatically operates the brakes to slow the vehicle and maintain a speed relative to the selected gear and the accelerator pedal position.

HDC will also work in neutral gear, and maintains the vehicle rolling speed by operating brakes automatically. HDC will deactivate automatically, if the vehicle speed is more than 45 kmph.

While HDC is controlling the vehicle speed, descent speeds can be varied using cruise control switches mounted on the steering wheel.

To decrease speed, press and hold “SET -” button. The vehicle speed at the point of switch release will become the new descent speed.

To increase, press and hold “SET +” button. The vehicle speed at the point of switch release will become the new descent speed. Alternatively, descent speeds can be adjusted by tapping the “SET _” or “SET +” buttons. Each press of the button will adjust the speed by approximately 0.5 kmph.

If the brake pedal is depressed when HDC is active, HDC is overridden and the brakes will perform as normal (a pulsation might be felt through the brake pedal). If the brake pedal is then released, HDC will recommence operating, if necessary.

HDC system monitors the brake temperature continuously. If brake application is continuous and brake temperatures are too high, HDC deactivates automatically. This is to ensure that the brake pads are not worn due to continuous brake application.

11.13 Hill Hold Control (HHC) (if equipped)

Hill Hold Control with acceleration sensor identifies gradients and holds the vehicle for about three to four seconds after the brakes have been released in order to prevent the vehicle from accidentally rolling backwards during a hill start.

Imagine a situation where your vehicle is stopped on an uphill incline. If you release the brake while moving off, there are chances that your vehicle may roll back. HHC helps in such situations by holding the vehicle from rolling back.

11.14 Cruise Control (if equipped)

Cruise control allows you to maintain a set speed without the need to keep your foot on the accelerator pedal. It should be used for cruising on straight, open highways. Never use it for city driving, inclines, winding roads, slippery roads, heavy rain or in bad weather conditions.It works on the closed loop system principle to maintain the set speed of the vehicle; the system controls the fuel injection of the engine in order to maintain the set speed.

Cruise control will function only under the following conditions:

• The vehicle is cruising above 20 kmph
• Engine RPM above 1200 RPM
• Vehicle is in any gear except 1st and reverse
• Clutch pedal released
• Brake pedal released
• Cruise is activated first time in an ignition cycle by SET + / SET button
• Subsequent cruise engagements can be done by RESUME SET+ /SET- buttons in the same ignition cycle

Cruise control is deactivated under the following conditions:

• CRUISE OFF button is pressed
• Brake or clutch pedal depressed. If the vehicle speed exceeds the cruise set speed by 30 kmph by accelerator pedal intervention
• If vehicle speed is increased by 10 kmph for more than 30 secs. by pressing the accelerator pedal

When Set+/Set- switch is pressed for more than 12 secs. (In this case, vehicle will not go into cruise mode in that ignition cycle. In order to restore the cruise function, switch OFF the ignition, wait for 30 secs. and switch ON the ignition.

Cruise influencing error indicated by Check Engine Lamp, OBD lamp, etc

11.14.1 Cruise ControlActivation

Drive the vehicle to the desired cruising speed (any value greater than 20 kmph), press and hold the SET+ button until the cruise lamp in the instrument cluster illuminates.

If cruise is deactivated (e. g. by depressing brake to handle an intervention in the road etc.) in current driving cycle, reactivate the Cruise to the last active Cruise Speed by pressing the RESUME button.

Cruise control may not hold the set speed when you are going up or down hills, and the vehicle may come out of cruise control. This is indicated by the cruise lamp going OFF in the instrument cluster.

11.14.2 Cruise Control De-activation

You can cancel cruise control in any of the following ways:

• Press the CRUISE OFF button in the steering wheel
• Press the brake pedal
• Gear selector moved into neutral
• HDC or ESP becomes active

11.14.3

SET + button is used to activate cruise control and also to increase the cruise set speed.

To increase the speed in very small amounts, press the SET + button. Each time you press, the cruise set speed increases by about 2 kmph. When you wish to continuously increase the cruising speed, press and hold the SET + button and release when the desired speed is reached.

11.14.4 SET - Button

To decrease the speed in small amounts, press the SET - button. Each time you press, the cruise set speed decreases by about 2 kmph.When you wish to continuously decrease the cruising speed, press and hold the SET- button. When the desired speed is reached, release the button.

11.14.5 Override Function

This function enables user to ramp up the cruising speed to overtake front vehicle.

The cruising speed can be increased by using accelerator pedal. User has to complete this action within 30 seconds, to maintain the cruise mode. If user exceeds the 30 seconds limit, cruise mode will be deactivated.

11.15 Stop/Start System

Stop/Start system automatically “stops” and “starts” the engine when idle at signals or long traffic jams. This in turn gives a better fuel efficiency. Stop/Start system is activated by the “Stop/Start” button in the central bezel switch bank. The LED on the button indicates the status of the button.

11.15.1 How does the Stop/Start System Work?

Let’s take a simple example of driving in traffic conditions within your city. Assume that your vehicle has stopped at a traffic junction due to a red signal. The following steps illustrate how the system functions:

• The vehicle has come to a halt at a traffic signal, is in the neutral gear and the clutch pedal is released.
• Accelerator pedal and clutch pedal are fully released .
• Vehicle battery should be in healthy condition .
• Engine is warm (Engine coolant temperature is between 250C and 100C). This is an extra precaution to ensure safe working of the engine .
• Fuel temperature is less than 60C .
• Gear in neutral .

For auto start to happen, the following conditions are to be met:

• Vehicle should have been stopped by the Stop/Start System .
• Gear lever is in the neutral position, Clutch pedal is fully depressed .
• Vehicle speed is zero .
• Stop/Start System is in active state .
• Bonnet should be closed.

11.16 Overview of the Stop/Start System

12.12.3 Frequently Asked Questions (FAQ)

1. What is the advantage of the system?
2. The Stop/Start System aids in attaining better fuel efficiency on your vehicle and thus reducing your running costs. However, the mileage improvement will depend upon various parameters such as prevailing traffic, driving patterns, etc.
3. What are the other advantages of the system?
   • Since the engine is switched off during traffic signals/ jams, considerable amount of CO2 release to the atmosphere is avoided. This reduces global warming and thus provides us with a cleaner atmosphere to live
   • Ability to start the engine by pressing the clutch pedal
   • Reduces noise pollution at traffic signals
4. Is it possible to start the engine through the clutch pedal for the first time?

   No, the engine can be cranked only with the ignition key for the first time. If the engine is stopped automatically by the system, only then it is possible to start the engine through clutch pedal.

5. How to activate/deactivate the system?

   The system is activated by default during every ignition cycle. The LED indication on the Stop/Start switch indicates the status of the system. The system can be turned OFF or back ON using the Stop/Start switch.

6. Whether the system will get activated as soon as the engine is started the first time with the ignition key?

   No, the Stop/Start system can be activated only by the Stop/Start switch, provided all listed conditions (in the previous section) are met. This is to ensure better performance of the engine in terms of fuel economy and durability.

7. What is to be done, if I don’t want the system to stop my engine at traffic signals/Jams?

   The system can be turned OFF by the Stop/Start button in the central bezel switch bank.

8. Whether the A/C will function, if the engine is switched off?

   No, the A/C will not work. However the blower will be in operation when the ignition is ON.

9. What will happen if I keep the clutch continuously pressed at traffic signals/jams?

   The system will not stop the engine if the clutch is continuously pressed since it indicates the driver’s intention of moving the vehicle immediately.

10. When the battery charge is low, whether the engine will be switched off?

    If the battery charge drops below a certain threshold level, the system will not stop the engine so as to preserve the battery from further draining.

11. Whether I will be able to operate the engine with the normal ignition key?

    Yes, normal operation with the ignition key is always possible.

12. Whether the vehicle will start (or) stop in gear?

    The vehicle will not start or stop automatically in gear to ensure safety. It will do so only in the neutral position of the gear lever.

13. Whether the system will stop my engine in moving traffic?

    No, the engine will be stopped only when the vehicle speed is zero.

14. Whether the audio system will be switched OFF, when the engine shuts down?

    No, the audio system will not be switched OFF and you can continue to enjoy the music.

15. Whether the engine will re-crank whenever the clutch pedal is pressed?

    No, when the engine is running, the starter motor will not attempt to re-crank.

16. If any component involved in the system fails, what will happen?

    The system has a built-in diagnostic module which understands the failure and immediately goes to bypass mode. In the bypass mode the engine can be turned ON and OFF by ignition key as usual.

11.18 Fuel

Use only commercially available vehicular Ultra-low Sulfur Highway Diesel that meets the BIS standard (Conforming to IS 1460;2010 BSIV/BSIII specification or equivalent). Information on diesel quality can normally be found in the fuel pump. Please contact filling station personnel in case labels in the pump cannot be found.

11.18.1 Fueling during Winter

During freezing weather if fuel is not winterized or is insufficiently winterized, waxing/gelling may start in fuel, leading to interruption in fuel supply to engine. For smooth functioning and reliable operation of the engine during cold weather conditions, use winterized ULSD which are available at the filling stations during winter months. Check with your fuel retailer for further details.

11.18.2 Minimum Fuel Requirement

It is recommended maintaining a minimum of 10 liters of fuel in the fuel tank. Driving the vehicle till the fuel tank is empty is not recommended. Always have sufficient fuel in the tank. Check the fuel level prior to starting your journey.

11.18.3 Fuel-Lid Opening and Closing

The remote fuel-lid can be opened by gently pressing the fuel lid button (adjacent to the head lamp leveling switch) on the instrument panel driver side.

Turn the fuel cap counter-clockwise to open. Refuel and put the cap back in its place and tighten in the clockwise direction till three distinct clicks are heard. Close the fuel lid shut.

11.18.4 Mechanical Override for Fuel Lid Opening

In the unlikely event of remote switch not opening the fuel lid, a mechanical over ride release is provided. It is located in the luggage compartment LH trim area behind the third row seats. Turn the knob anti-clockwise to open the fuel lid.

12 WHEELS AND TYRES

12.1 Tyre Information

12.2 Tyre Rating

Your vehicle is originally equipped with tyres supplied by a reputable manufacturer. If you ever have any questions regarding your tyres, please refer to literature supplied by the tyre manufacturer, or to the separate tyre warranty provided by the tyre manufacturer. You may also contact Mahindra directly, or the tyre manufacturer.

The tyre rating of XUV500 is;

• 235/65 R17 104H

Tyre rating is explained as below;

Callout (A): 235 (Three-digit number): This number gives the width in millimeters of the tyre from sidewall edge to sidewall edge. This is called as “Section Width”.

Callout (B): 65 (Two-digit number): This number, known as the aspect ratio, gives the tyres ratio of height to section width.

Callout (C): R: This is the Tyre Construction Code. The “R” stands for Radial.

Callout (D):17 (Two-digit number): This number is the wheel or rim diameter in inches.

Callout (E):104 (Two or three digit number): This number is the tyres load index. It is a measurement of how much weight each tyre can support.

Callout (F): H: Tyre speed rating or speed symbol. Never drive the vehicle faster than the tyre speed rating. The speed rating denotes the speed at which a tyre is designed to be driven for extended periods of time under a standard condition of load and inflation pressure.

12.2.1 Speed Rating

12.3 Tyre Label (Vehicle Placard)

Tyre Label (Vehicle Placard) is located on the driver side inner B-pillar. This placard tells you important information about tyre size designed for your vehicle, and the tyre inflation pressures for the front & rear tyres.

12.4 Tyre Pressure

Proper tyre inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tyre pressure;

• Safety
• Economy
• Ride Comfort and Vehicle Stability

Proper tyre inflation contributes to a comfortable and safe ride. Overinflating produces a jarring and uncomfortable ride. Both underinflation and overinflation affect the stability of the vehicle and can produce a feeling of sluggish response or over responsiveness in the steering. Unequal tyre pressures can cause erratic and unpredictable steering response or may cause the vehicle to drift left or right.

Improper inflation pressures can cause uneven wear patterns to develop across the tyre tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tyre replacement. Underinflation also increases tyre rolling resistance and results in higher fuel consumption.

12.4.1 Inspection and Adjustment Procedure

The tyre pressure should be checked and adjusted, as well as inspected for signs of tyre wear or visible damage, at least once a month. Use a good quality pressure gauge to check tyre pressure. Do not make a visual judgement when determining proper inflation. Radial tyres may look properly inflated even when they are under-inflated. At the same time, each tyre should be inspected for signs of tyre wear or visible damage.

Inflation pressures specified on the placard are always cold tyre inflation pressures. Cold tyre inflation pressure is defined as the tyre pressure after the vehicle has not been driven for at least three hours, or driven less than 1 km after a three-hour period. Check tyre pressures more often if subject to a wide range of outdoor temperatures, as tyre pressures vary with temperature changes. Tyre pressures change by approximately 1 psi (7 kPa) per 7°C of air temperature change. Keep this in mind when checking tyre pressure inside a garage, especially in the winter.

When it was new, the spare tyre in your vehicle was fully inflated. However, a spare tyre can lose pressure over time. In order to avoid being stranded, check the spare tyre air pressure frequently.

12.4.2 Inflating Your Tyres

Safe operation of your vehicle requires that your tyres are properly inflated. Remember that a tyre can lose up to half of its air pressure without appearing flat.

At least once a month or before long trips, inspect each tyre and check the tyre pressure with a tyre gauge (including spare tyre). Inflate all tyres to the recommended inflation pressure.

You are strongly urged to buy a reliable tyre pressure gauge, as automatic service station gauges may be inaccurate. Mahindra recommends the use of a digital or dial-type tyre pressure gauge rather than a stick-type tyre pressure gauge.

Use the recommended cold inflation pressure for optimum tyre performance and wear. Under-inflation or over-inflation may cause uneven tread wear patterns.

12.5 Tyre Rotation Recommendations

Tyres on the front and rear axles of vehicles operate at different loads and perform different steering, handling, and braking functions. For these reasons, they wear at unequal rates and develop irregular wear patterns.

Rotation will increase tread life, help to maintain mud, snow, and wet traction levels, and contribute to a smooth, quiet ride. Follow the recommended tyre rotation frequency for your type of driving.

It is recommended rotating the tyres as per the "Maintenance Schedule".

The suggested rotation method is the "forward-cross" shown in the diagram. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on On/Off-road type tyres.

Rotation will increase tread life, help to maintain mud, snow, and wet traction levels, and contribute to a smooth, quiet ride. Follow the recommended tyre rotation frequency for your type of driving. More frequent rotation is permissible if

desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being performed.

12.5.1 Changing a Flat Tyre

Refer to “If you have a Flat Tyre” section in the General chapter for details.

12.5.2 Wheel Tightness

when you change a wheel, remove all rust and dirt at all locations where the wheel contacts the wheel hub. Use a scraper or wire brush to be sure that you remove all rust and dirt.

12.6 Tiretronics (if equipped)

Tiretronics is an electronic system designed to monitor the air pressure inside the pneumatic tyres. This system will alert the driver if the tyre pressure falls below the low pressure or raises above high pressure warning limit for any reason, including low temperature effects and natural pressure loss through the tyre.

The Tiretronics will continue to alert the driver and will not turn off until the tyre pressure is inflated to the recommended pressure.

12.6.1 Operation of Tiretronics

Tiretronics uses wireless technology with wheel rim mounted electronic sensors to monitor tyre pressure levels. Sensors mounted to the valve stem of each wheel, transmit tyre pressure readings to the receiver module. Receiver module in turn will communicate this information to the instrument cluster and infotainment system. Tyre locations will display as OK, if all tyre pressure and temperature are in the recommended range.

The Tiretronics has been customised only for the manufacturer’s genuine tyres and wheels. Tiretronics pressure limits and warning messages have been established for the tyre size equipped on your vehicle.

Replacement of manufacturer’s parts with a different size, type or style of components may damage the sensor and lead to incorrect readings.

Do not use aftermarket tyre sealants or balance beads if your vehicle is equipped with Tiretronics. Failure to comply may lead to sensor damage.

The Tiretronics is not intended to replace normal tyre care and maintenance or to provide warning of a tyre failure or condition.

The Tiretronics should not be used as a tyre pressure gauge while adjusting vehicle tyre pressure.

Driving with under-inflated tyres cause the tyres to overheat and may lead to tyre failure.

Under-inflated tyres reduce fuel efficiency, tyre tread life and may affect the vehicle's manoeuvrability & braking ability.

The Tiretronics is not a substitute for tyre maintenance, it is the driver's responsibility to maintain correct tyre pressure using an accurate pressure gauge, even if under-inflation has not reached the level to trigger illumination of the Tiretronics warning indicator.

12.6.2 Tiretronics Warning Lamp

Tiretronics warning lamp will blink for 75 seconds (approx.) and remain ON in the instrument cluster, if any of the below mentioned condition occurs in the tyres:

• Sensor signal missing
• Sensor faulty

The error is also displayed on the infotainment screen as below. If above condition occurs, contact the nearest Authorised Mahindra Dealer for further assistance.

Examples of Tiretronics warning lamp illumination and corresponding infotainment screen display;

Low Pressure

High Pressure

Air Leakage

12.6.3 Tiretronics Learning

After a tyre rotation or Tiretronics sensor replacement, the receiver must be learnt, else the Tiretronics warning lamp indicates a malfunction.

Tiretronics learning button (A) is located to the left hand side of the instrument cluster.

12.6.4 Tiretronics Learning Procedure

1.Press the Tiretronics button in the cluster and turn ignition ON along with the button pressed. The infotainment screen displays as below and Tiretronics warning lamp in the cluster starts blinking.

2.Start removing air from front left tyre, once the tyre gets learnt, vehicle alarm and hazard lamps flash once. The infotainment screen display is as below:

3.Repeat the above step for front right tyre, rear right tyre and rear left tyre (in the same order). Corresponding infotainment screen displays are as below:

4. Start removing air from spare tyre. Once the tyre gets learnt, vehicle alarm and hazard lamps flashes to indicate all the tyres were learnt. The infotainment screen display is as below indicating all tyres were learnt successfully.

If there were any problem in learning, the alarm and hazard lamps flash 3 to 5 times to indicate the tyre learning was not complete.

12.6.5 Tyre Swap

If a tyre was swapped with the spare tyre, system alerts the user through infotainment as below:

Please note, if swapping is done for more than one tyre or with the other running tyres, system cannot identify the same and the system needs to be relearned

14.2 Opening and Closing the Hood

The hood release lever is located in the driver side footwell area, below the instrument panel. To open hood equipped with gas struts, follow the steps below:

1. Pull the lever below the driver side instrument panel to release the hood.

2. Lift the hood a little to access the safety latch holding the hood striker. This safety latch is located below the hood at the centre.

3. Lift the safety latch and lift the hood.

4. The hood will lift automatically and will be supported by the gas struts.

5. In some variants, the hood is supported by a stay rod.

14.3 Engine Compartment

Maintenance is classified as below;

• General Maintenance
• Scheduled Maintenance

14.4 General Maintenance

Listed below are the general maintenance items that should be performed frequently. In addition to checking the items listed below, if you notice any unusual noise, fluid leakages, smell or vibration, you should investigate the cause or take your vehicle to your Authorized Mahindra Dealer or a qualified service shop immediately.

• Front windshield washer fluid level
• Engine coolant level
• Battery condition
• Brake/Clutch fluid level
• Engine oil level
• Power steering fluid level
• Fluid leaks
• Hoses, joints and pipes for any abnormalities

• Lights
• Warning lamps
• Windshield wipe and wash
• Steering wheel
• Seats
• Seat belts
• Accelerator pedal
• Brake pedal
• Brakes
• Parking brake
• Gear lever shift mechanism

• Lamps
• Fluid leaks
• Doors and engine hood latches
• Tyre inflation pressure
• Tyre surface/thread and wheel nuts

14.9 Wiper Blades

Lift the wiper arm from its position. Expose the blade lip for inspection. Clean the wiper blade lips with water applied with a soft sponge. If the wiper blade is not wiping the glass satisfactorily or is worn-out, cut, cracked or bulging, get it replaced at an Authorised Mahindra Dealer.

14.9.1 Changing the Wiper Blade

1. Lift the arm and position the wiper blade at right angles to the wiper arm.

2. Press the retaining clip in the opposite direction, disengage the wiper blade and pull it off the arms

3. Hold the end of the rubber and pull until the tabs are free of the metal support.

4. Carefully insert the new blade rubber. Then instal the blade assembly in the reverse order of removal.

14.15 Projector Head Lamp - Type 1

14.16 Projector Head Lamp Type 2